XC7Z045-1FFG676C - 350K Zynq SoC, 667MHz | AMD | FPGA
MPN: XC7Z045-1FFG676C ✓ Hoạt độngXC7Z045-1FFG676C Tóm tắt
A Zynq-7000 system-on-chip is an FPGA with programmable logic integrated with a hard processor subsystem. Unlike a conventional processor, the FPGA fabric can implement parallel data paths, custom interfaces, accelerators, and real-time control logic. The integrated dual-core Arm Cortex-A9 subsystem executes software, operating systems, networking functions, and control code, allowing one device to combine sequential processing and hardware parallelism.
Key features include 350K FPGA logic cells, dual-core Arm Cortex-A9 processing, CoreSight debug support, and 130 user I/Os. The Kintex-7 programmable logic fabric supports parallel sensor processing, video pipelines, high-speed data acquisition, and hardware-assisted control. A 676-ball FCBGA provides the high pin count needed for interfaces, memory connectivity, power, ground, and differential I/O in compact embedded systems.
The part is manufactured on a 28 nm process and uses a mixed architecture in which software controls system behavior while programmable logic accelerates data-intensive workloads. The processor side supports operating-system-based designs, and the programmable side can implement interfaces whose timing and parallelism would be inefficient using the processor alone. This architecture is particularly useful when deterministic response, low-latency transfers, or concurrent real-time processing are required.
Typical applications include industrial machine vision, industrial automation, robotics, communications equipment, embedded control, high-speed data acquisition, and defense or aerospace electronics. The 667 MHz dual-core subsystem is appropriate for protocol handling and supervisory control, while the FPGA fabric can accelerate image processing, filtering, packet inspection, or sensor fusion without excessive processor overhead.
Design considerations include confirming the FCBGA land pattern, power rails, decoupling strategy, DDR memory interface, and pin constraints before layout. Because this is a high-pin-count BGA, escape routing, via distribution, and thermal performance require careful PCB planning. The commercial-grade C suffix should be checked against the final ambient-temperature range and system qualification requirements.
This page combines the device architecture, package details, engineering-use guidance, and same-footprint replacement analysis to support faster selection and board-level planning for Zynq-7000 designs.
Bộ thay thế dễ dàng lắp đặt cho XC7Z045-1FFG676C — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với XC7Z045-1FFG676C (cùng hình factor và footprint) — khác nhau ở Device Type, Package, Architecture, FPGA Family, Supply Voltage.
XC7Z045-1FFG676I
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →XC7Z045-2FFG676I
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →XC7Z045-2FFG676E
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →XC7Z045-2FBG676I
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →XC7Z045-3FFG676E
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →XC7Z045-1FFG676C Tỷ lệ tối đa & tính chất điện
| Device Type | Zynq-7000 system-on-chip |
| FPGA Family | Kintex-7 |
| Processor Core | Dual-core Arm Cortex-A9 |
| Processor Maximum Frequency | 667 MHz |
| FPGA Logic Cells | 350K |
| User I/O Count | 130 |
| Debug Support | CoreSight |
| Architecture | Zynq-7000 first-generation architecture |
| Hộp | 676-FCBGA, 27 x 27 mm |
| Package Ball Count | 676 balls |
| Process Technology | 28 nm |
| Điện áp cung cấp | 1.2 V / 3.3 V |
| Operating Temperature Grade | 0C to 85C |
| Architecture Instruction Set | ARMv7-A, Thumb-2, 32-bit |
| Debug Interface | ARM CoreSight |
| Programmable Logic Type | Kintex-7 FPGA |
Hướng dẫn cấu hình chân XC7Z045-1FFG676C 676 balls
Cấu hình chân cho XC7Z045-1FFG676C (676 balls gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho XC7Z045-1FFG676C.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
XC7Z045-1FFG676C phù hợp cho 6 Áp dụngs: Industrial Machine Vision, Industrial Automation and Robotics, High-Speed Data Acquisition, Communications and Network Equipment, Aerospace and Defense Control, Embedded Control and Sensor Fusion.
Industrial Machine Vision
The XC7Z045-1FFG676C is well suited to industrial camera and inspection systems that combine high-volume pixel processing with embedded supervisory control. Its 350K Kintex-7 logic cells can implement parallel stages such as correction, color conversion, thresholding, and feature extraction, while the dual-core 667 MHz Arm Cortex-A9 subsystem manages sensors, image buffers, networking, and operator interfaces. The 130 user I/Os support camera, trigger, storage, and communications connectivity. A designer should use the manufacturer ball map and DDR interface constraints to partition data paths, and should confirm that the enclosure remains inside the device's 0C-to-85C commercial operating range.
Được đề xuất
Industrial Automation and Robotics
The XC7Z045-1FFG676C can combine deterministic FPGA logic with a programmable processor for robot controllers, motion systems, and factory automation equipment. The Kintex-7 fabric can implement timing-critical interfaces, encoder processing, or deterministic data paths, while the dual-core Arm subsystem executes control software, diagnostics, and industrial-network protocols. Its 350K logic cells provide substantial parallel-processing capacity without requiring a separate FPGA. Engineering teams should partition latency-critical functions into programmable logic, reserve processor resources for supervisory control, and validate timing and thermal margins against the actual actuator drive, switching noise, and enclosure environment.
Được đề xuất
High-Speed Data Acquisition
The XC7Z045-1FFG676C supports acquisition systems that must move and process parallel sensor data while also performing control and communication functions. Its FPGA fabric can accommodate capture logic, filtering, triggering, and data-format conversion, and the dual-core 667 MHz Arm processor can organize buffers, control transfers, and communicate with a host. The 130 user I/Os and 676-ball package offer extensive connectivity, but the achieved sample rate depends on the selected I/O standards, memory topology, timing constraints, and board-level signal integrity. Designs should use the manufacturer pin descriptions and interface timing specifications rather than assuming generic BGA connectivity.
Được đề xuất
Communications and Network Equipment
The XC7Z045-1FFG676C fits communication equipment that benefits from concurrent packet processing, protocol control, and programmable interfaces. The 350K FPGA fabric can implement parallel packet classification, filtering, or custom transport logic, while the dual-core Arm Cortex-A9 subsystem runs networking services, management code, and operating-system tasks. The 667 MHz -1 processor grade is suitable for many supervisory and control workloads when maximum software throughput is not the primary constraint. Board designers should define the DDR memory interface carefully, isolate high-speed routing according to the manufacturer layout guidance, and verify protocol timing with the intended Vivado design configuration.
Được đề xuất
Aerospace and Defense Control
The XC7Z045-1FFG676C can serve as the programmable foundation for embedded control, signal processing, and mission-data handling systems. Its dual-core Arm processor supports conventional software, while the Kintex-7 fabric allows critical pipelines and interfaces to be implemented as deterministic hardware. The 350K logic cells and 130 user I/Os provide substantial resources, and the 676-ball FCBGA supports complex board-level connectivity. The commercial C suffix has a 0C-to-85C range, so an aerospace or defense program must verify whether an appropriate temperature-qualified ordering option is required and complete program-specific qualification and environmental testing before deployment.
Được đề xuất
Embedded Control and Sensor Fusion
The XC7Z045-1FFG676C is suitable for embedded systems that combine sensor interfaces, local processing, and application-level control. The programmable logic can handle concurrent sampling, sensor timing, filtering, and data preparation, while the dual-core Arm subsystem executes algorithms, manages storage, and presents local or network interfaces. This division of work can reduce processor bottlenecks and provide more predictable latency for time-sensitive measurements. A robust implementation should define memory bandwidth and DDR timing early, constrain interfaces through the Vivado tool flow, and review thermal performance because the 676-pin FCBGA concentrates power delivery and signal routing requirements into a compact 27 x 27 mm package.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho XC7Z045-1FFG676C — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | XC7Z045-1FFG676I | XC7Z045-2FFG676I | XC7Z045-2FFG676E | XC7Z045-2FBG676I | XC7Z045-3FFG676E |
|---|---|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| Package | 676-FCBGA (27x27) | 676-FCBGA (27x27) | 676-FCBGA (27x27) | 676-FCBGA (27x27) | 676-FCBGA (27x27) | 676-FCBGA (27x27) |
| Processor Core | Dual-core Arm Cortex-A9 | Dual-core Arm Cortex-A9 | Dual-core Arm Cortex-A9 | Dual-core Arm Cortex-A9 | Dual-core Arm Cortex-A9 | Dual-core Arm Cortex-A9 |
| FPGA Logic Cells | 350K | 350K | 350K | 350K | 350K | 350K |
| Processor Speed Grade | -1, 667 MHz | -1, 667 MHz | -2, approximately 1 GHz | -2, approximately 1 GHz | -2, approximately 1 GHz | -3, 1 GHz |
| Temperature Grade | C commercial, 0C to 85C | I industrial | I industrial | E extended | I industrial | E extended |
| Process Technology | 28 nm | 28 nm | 28 nm | 28 nm | 28 nm | 28 nm |
| FPGA Family | Kintex-7 | Kintex-7 | Kintex-7 | Kintex-7 | Kintex-7 | Kintex-7 |
Bảo phân biệt quan trọng
- Commercial temperature grade with a 667 MHz processor speed rating (vsXC7Z045-1FFG676I)
- Lower processor speed grade supports a different timing and power design point (vsXC7Z045-3FFG676E)
- Combines 350K logic cells with a dedicated dual-core processor subsystem (vsXC7Z045-2FBG676I)
Ghi chú thiết kế
Use the manufacturer power-decoupling recommendations for every voltage rail and preserve the placement of bulk and high-frequency capacitors at the device pins. The 1.2 V and 3.3 V rails serve different sections of the SoC, so treat them as separate distribution networks and validate steady-state and transient current against the selected design. For dense FPGA activity, monitor voltage droop during processor and logic execution rather than estimating adequacy from average current alone.
The 676-ball FCBGA requires a carefully assigned escape-routing strategy with adequate via arrays, uniform power distribution, and short return paths. Follow the AMD package drawing for land pattern, ball locations, and exposed thermal requirements. DDR memory connections and high-speed interfaces are especially sensitive to routing geometry, so establish constraints in the FPGA design tool and verify length, skew, return-path continuity, and via transitions before release.
Thermal performance depends on the PCB stack-up, copper distribution, airflow, and adjacent heat sources, so the compact 27 x 27 mm FCBGA should not be evaluated by package size alone. Provide continuous copper beneath and around the device where the package design permits, maintain the manufacturer's via requirements, and run the intended worst-case processor and FPGA workload. Validate the resulting junction-temperature margin under the final enclosure rather than at board level.
Do not treat a similarly named XC7Z045 ordering code as interchangeable without checking speed grade and temperature suffix. The -1 and -3 grades can change timing and power behavior, while C, E, and I suffixes define different operating environments. Also confirm the FFG versus FBG package details against the manufacturer package drawing, because changing the suffix without verifying the ball map can create package or connectivity errors even when the device family is the same.
Thông tin tuân thủ
Compliance attributes were not identified in the cited device records and must be confirmed from the current AMD product documentation or the supplier's material declaration.