XMC1100-T016X0064AAXUMA1 - 32MHz Cortex-M0 64KB MCU | Infineon
MPN: XMC1100-T016X0064AAXUMA1 ✗ Cuối đờiXMC1100-T016X0064AAXUMA1 Tóm tắt
A microcontroller is a programmable system-on-chip that integrates a processor core, nonvolatile program memory, volatile data memory, peripherals, and interface circuitry into one component. The XMC1100 belongs to the XMC1000 family of Cortex-M0 microcontrollers, a low-complexity branch of 32-bit embedded processing. This family targets entry-level industrial and consumer designs and can support cost-sensitive replacements for conventional 8-bit and 16-bit microcontroller systems.
The target device combines a 32 MHz Arm Cortex-M0 core with 64 KB of flash and a six-channel ADC. Its 32-bit architecture supports efficient handling of firmware, control loops, communications, and general-purpose peripheral tasks while retaining a compact 16-pin package. The six-channel ADC provides multiple analog input paths for sensing applications, allowing several physical measurements to be handled by one microcontroller rather than requiring separate analog front-end devices.
The XMC1100 series is positioned for applications that require basic embedded control without the memory and peripheral complexity of a higher-end microcontroller. Its operating concept combines deterministic embedded execution with integrated analog acquisition and serial peripherals. The 64 KB flash configuration also leaves a defined code-storage footprint for compact control firmware, bootloader functions, and application-specific routines.
Typical uses include industrial sensor modules, compact motor-control nodes, small appliance controllers, building equipment, communication peripherals, and consumer products that need several analog inputs. The part is especially relevant where board area is constrained but a 16-pin package can still provide access to the required digital and analog signals. A suitable application should map every required signal, peripheral, power rail, and programming interface to the available TSSOP-16 footprint before design release.
The principal design consideration is pin-budget allocation. In a 16-pin package, power pins, ground connections, clocking, programming, reset, and communication signals can constrain the number of application I/O pins. Place the decoupling capacitors adjacent to their supply pins, route programming and debug access for reliable field updates, and confirm signal directions and analog limits against the manufacturer pin-description table before laying out the PCB.
This page consolidates the XMC1100 device identity, verified manufacturer documentation, package information, replacement options, and practical design guidance. It also distinguishes exact memory configurations and silicon-step options so engineers can evaluate drop-in choices without confusing a lower-memory variant or a different revision with an equivalent 64 KB AA-step device.
Bộ thay thế dễ dàng lắp đặt cho XMC1100-T016X0064AAXUMA1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với XMC1100-T016X0064AAXUMA1 (cùng hình factor và footprint) — khác nhau ở Flash Memory, Package, Architecture, Core, Supply Voltage.
XMC1100T016X0064ABXUMA1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →XMC1100-T016F0064-AB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
XMC1100T016F0064ABXUMA1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →XMC1100-T016F0016AAXUMA1
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
XMC1100-T016F0064AAXUMA1
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
XMC1100-T016X0064AAXUMA1 Tỷ lệ tối đa & tính chất điện
| Processor Core | Arm Cortex-M0 |
| CPU Frequency | 32 MHz |
| Architecture | 32-bit |
| Core Count | 1 core |
| Flash Memory | 64 KB |
| Flash Organization | 64K x 8 bits |
| ADC Channel Count | 6 channels |
| Hộp | PG-TSSOP-16-8, 16 pins |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân XMC1100-T016X0064AAXUMA1 pg-tssop-16-8, 16 pins
Cấu hình chân cho XMC1100-T016X0064AAXUMA1 (pg-tssop-16-8, 16 pins gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho XMC1100-T016X0064AAXUMA1.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
XMC1100-T016X0064AAXUMA1 phù hợp cho 6 Áp dụngs: Industrial Sensor Module, Compact Motor Control Node, Building Equipment Controller, Small Appliance Controller, Communication Peripheral, Consumer Control Product.
Industrial Sensor Module
The XMC1100-T016X0064AAXUMA1 fits compact industrial sensor modules because it combines a 32-bit Cortex-M0 core, 64 KB of flash, and a six-channel ADC in a 16-pin package. The ADC can acquire multiple analog sensor signals while local firmware performs filtering, thresholding, compensation, and digital communication. Placing the MCU close to the sensors reduces wiring complexity and helps keep the analog path compact. The design must allocate pins carefully because the TSSOP-16 package also requires power, ground, programming, and clock functions. Verify the analog input limits and pin assignments in the manufacturer datasheet, and provide local filtering close to each sensor input to preserve signal quality.
Được đề xuất
Compact Motor Control Node
The XMC1100-T016X0064AAXUMA1 is appropriate for a small motor-control or actuator node that benefits from 32-bit processing without requiring a larger microcontroller package. Its 32 MHz Cortex-M0 core can execute position, speed, or duty-cycle control routines, while the six-channel ADC can monitor command inputs or analog feedback conditions. The 64 KB flash accommodates local control firmware and calibration logic. Because the device has only 16 pins, external drivers may be required for power switching, level translation, or high-current output. Keep high-current or fast-switching paths away from sensitive analog inputs, and confirm timer outputs and alternate-function mappings against the pin-description table.
Được đề xuất
Building Equipment Controller
The XMC1100-T016X0064AAXUMA1 can serve as the controller in a compact building-equipment module such as a sensor, actuator, or local supervisory node. The 32-bit Cortex-M0 core supports event handling and communication firmware, while 64 KB of flash provides space for application logic and field-update functions. The six-channel ADC is useful when the equipment exposes several analog measurements through a common connector. A practical design should isolate field-wired inputs from the microcontroller through appropriate protection, maintain predictable grounding between sensor and power domains, and account for temperature and supply variations. Confirm electrical limits, reset behavior, and communication assignments from the Infineon manufacturer datasheet before production release.
Được đề xuất
Small Appliance Controller
The XMC1100-T016X0064AAXUMA1 suits small appliance controllers where a compact package, local flash, and analog measurement capability are needed. A 32 MHz Cortex-M0 core can handle motor timing, button logic, sensor evaluation, and communication tasks in one device, while the six-channel ADC supports temperature, level, or feedback measurements. The 64 KB flash configuration allows a more capable application program than the 16 KB XMC1100 option. Designers should identify which loads require external transistors or drivers and keep switching nodes away from analog traces. Use the manufacturer pin table to validate functions after routing, and review startup, reset, and brownout requirements for appliance mains-related modules.
Được đề xuất
Communication Peripheral
The XMC1100-T016X0064AAXUMA1 can be used in a small communication peripheral or protocol adapter where local framing, configuration, and status handling are required. Its 32-bit Cortex-M0 architecture provides a straightforward execution environment for packet processing, while 64 KB of flash supports protocol firmware and a bootloader. The six-channel ADC can also monitor a supply rail or external analog condition when the design requires telemetry. Serial-interface pins, programming access, and supply pins must be prioritized when selecting the package because alternate-function multiplexing can limit available I/O. Confirm the supported interface set and electrical characteristics in the manufacturer datasheet, and provide a stable clock and decoupling arrangement for reliable communication timing.
Được đề xuất
Consumer Control Product
The XMC1100-T016X0064AAXUMA1 is suitable for compact consumer products that need programmable control, local storage, and limited analog sensing. The XMC1000 family targets general-purpose consumer as well as industrial applications, and this ordering option provides 64 KB of flash in a small TSSOP-16 package. Typical products include accessory controllers, compact timers, and simple condition-monitoring products. The implementation should minimize external components where practical, but decoupling and signal conditioning remain necessary for stable operation. Confirm package pin directions and exposed alternate functions, provide accessible programming or recovery provisions for production, and verify EMC behavior in the final enclosure because cable or connector transitions can disturb sensitive ADC measurements.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho XMC1100-T016X0064AAXUMA1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | XMC1100T016X0064ABXUMA1 | XMC1100-T016F0064-AB | XMC1100T016F0064ABXUMA1 | XMC1100-T016F0016AAXUMA1 | XMC1100-T016F0064AAXUMA1 |
|---|---|---|---|---|---|---|
| Package | PG-TSSOP-16-8, 16 pins | PG-TSSOP-16-8, 16 pins | PG-TSSOP-16-8, 16 pins | PG-TSSOP-16-8, 16 pins | PG-TSSOP-16-8, 16 pins | PG-TSSOP-16-8, 16 pins |
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Processor Core | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 |
| CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 64 KB | 64 KB | 64 KB | 64 KB | 16 KB | 64 KB |
| Architecture | 32-bit single-core | 32-bit Cortex-M0 | 32-bit Cortex-M0 | 32-bit Cortex-M0 | 32-bit Cortex-M0 | 32-bit Cortex-M0 |
| Silicon Step | AA step | AB step | AB step | AB step | AA step | AA step |
| Ordering Configuration | T016X0064AAXUMA1 | T016X0064ABXUMA1 | T016F0064-AB | T016F0064ABXUMA1 | T016F0016AAXUMA1 | T016F0064AAXUMA1 |
| Special Features | General-purpose XMC1100 with 64 KB flash | General-purpose XMC1100 with 64 KB flash | General-purpose XMC1100 with 64 KB flash | General-purpose XMC1100 with 64 KB flash | General-purpose XMC1100 with 16 KB flash | General-purpose XMC1100 with 64 KB flash |
Bảo phân biệt quan trọng
- Full 64 KB flash in the same 16-pin footprint (vsXMC1100-T016F0016AAXUMA1)
- Direct AA-step family configuration (vsXMC1100T016X0064ABXUMA1)
- Six-channel analog acquisition in a compact package (vsXMC1100-T016F0016AAXUMA1)
Ghi chú thiết kế
Allocate the 16 pins before committing to the schematic. Power, ground, reset, programming access, clocking, communications, and six-channel ADC demand can leave fewer application I/O pins than the package count suggests. Cross-check alternate functions in the manufacturer pin-description table, keep debug or programming access reachable for production, and verify that every selected alternate function does not conflict with an ADC or communication channel.
Place the required supply decoupling capacitors as close as practical to the corresponding device pins, with the shortest possible supply and ground paths. Use the manufacturer datasheet to determine the exact capacitor values, tolerances, voltage ratings, and power-up sequence. Do not infer a single capacitor value from generic MCU practice, because the datasheet may distinguish core, analog, and external supply requirements.
Keep analog sensor inputs away from switching nodes, high-current outputs, and clock traces. Route the ADC input path directly to the MCU pin through the intended analog network, avoid sharing narrow return paths with noisy loads, and provide a quiet ground reference where the application permits. The six-channel ADC makes input multiplexing and pin assignment important, so verify each analog channel against its alternate-function limitations.
Do not treat an ordering-code variant as interchangeable solely because it uses the same package. Confirm memory capacity, silicon step, temperature rating, qualification status, and orderable package code for every replacement. In particular, XMC1100-T016F0016AAXUMA1 has 16 KB rather than 64 KB of flash, while AB-step options require a review of device-specific documentation and firmware support.
Thông tin tuân thủ
Exact compliance declarations and automotive qualification must be confirmed for the specific ordering code with Infineon. General family positioning does not establish qualification for XMC1100-T016X0064AAXUMA1.