產品(46,000+)

MAX318CPA+ - 35 Ohm SPST CMOS Analog Switch | Analog Devices
MAX318CPA+

MAX318CPA+ - 35 Ohm SPST CMOS Analog Switch | Analog Devices

The Analog Devices MAX318CPA+ is a precision, normally open, single-pole single-throw CMOS analog switch with an on-resistance of 35 ohms, housed in an 8-pin PDIP package. It routes one analog signal using a 1:1 SPST topology and is designed for precision signal-selection and test systems. An analog switch is a semiconductor interface device that connects or disconnects an analog signal path under digital control. The MAX318CPA+ belongs to the analog switch hierarchy within interface ICs and multiplexers, providing a simpler alternative to a multi-channel multiplexer when only one signal path must be selected. Its normally open configuration keeps the switched node disconnected until the control input activates the path. Key characteristics include a maximum on-resistance of 35 ohms, operation from 4.5 V to 20 V, and normally open SPST behavior. The device is specified as a precision CMOS analog switch with low on-resistance that remains substantially flat across the analog signal range. According to the Analog Devices MAX318 product page, on-resistance is guaranteed below 35 ohms and is matched within 2 ohms between channels in the associated precision-switch family. The MAX318CPA+ is intended for precision instrumentation, signal routing, test and measurement equipment, industrial control interfaces, and data acquisition systems. Its single-channel architecture simplifies control logic while preserving the low resistance required to transfer low-level or precision analog signals. The 8-pin PDIP package also supports conventional through-hole assembly and prototype boards where fine-pitch surface-mount routing would be inconvenient. Designers should verify the control logic, supply voltage, allowable signal voltage, and switching transients against the manufacturer data sheet before use. Because an analog switch can introduce small resistance variation, channel resistance matching, charge injection, off leakage, and bandwidth determine whether it is suitable for a particular signal path. Input and output protection may also be required when external voltages exceed the device ratings. This page combines the manufacturer specifications, verified sourcing links, application guidance, comparison information, and practical design notes to support component selection and PCB implementation. The MAX318CPA+ is best suited to designers who need a simple, normally open, precision SPST switch rather than a multi-channel multiplexer.

詢價 聯絡我們
MAX318CSA+ - SPST NO CMOS Analog Switch, 35 Ohm | Maxim
MAX318CSA+

MAX318CSA+ - SPST NO CMOS Analog Switch, 35 Ohm | Maxim

The Maxim Integrated MAX318CSA+ is a precision, single-pole single-throw (SPST) normally-open CMOS analog switch with a maximum on-resistance of 35 Ohm, packaged in an 8-pin SOIC (NSOIC) surface-mount package. It is a 1:1 multiplexer: one independent switch, one signal path, complementary-family sibling to the MAX317 (normally closed) and MAX319 (SPDT) parts in the same series. An analog switch is a solid-state, MOSFET-based signal router that connects or disconnects an analog signal path under digital control, sitting in the interface IC layer between sensors, converters and a system microcontroller. Unlike a mechanical relay, it switches in nanoseconds with negligible off-state leakage, making it the standard building block for sample-and-hold front ends, programmable gain stages, test-point muxes and isolated-signal routing. Key characteristics of the MAX318CSA+ include a maximum on-resistance of 35 Ohm, on-resistance matching held within 2 Ohm between channels and variation of only 3 Ohm maximum across the analog signal range, and very low leakage of less than 250 pA at +25 degC rising to less than 6 nA at +85 degC. The part is listed in production by Analog Devices and is specified over a 0 degC to +70 degC commercial temperature range in the SOIC package. Internally the device uses CMOS transmission gates, so the signal path is symmetrical and the switch behaviour does not depend on the control polarity in the same way a bipolar multiplexer does. The small, flat on-resistance curve preserves signal integrity for low-frequency analog signals, while the low leakage keeps the off-state contribution to system error negligible when a single measurement or sensor node is selected. Typical uses include routing sensor outputs into a single ADC input, multiplexing discrete resistive networks into a programmable gain amplifier, isolating a precision reference from a measurement node, selecting between test points during board bring-up, and building small sample-and-hold front ends in instrumentation equipment. Any of these functions can also be handled with a relay, but the CMOS switch removes the slow mechanical switching time and the contact bounce that plague relay-based solutions at higher cycle rates. When laying out the MAX318CSA+, place the device close to the source and destination of the analog path so that the switched trace stays short and the 35 Ohm series resistance has the least effect on signal settling. Keep the supply decoupling capacitor adjacent to the V+ and ground pins, and route control traces away from the analog node where board area allows, because charge injection through the control line can create a transient step at the moment of switching. This page consolidates the distributor availability picture, the family-level drop-in alternatives in the same 8-SOIC footprint, and the practical routing and layout notes that engineers usually have to piece together from the manufacturer data sheet and application experience.

詢價 聯絡我們
MAX319CSA+ - Precision 35Ω CMOS SPDT Switch | Analog Devices
MAX319CSA+

MAX319CSA+ - Precision 35Ω CMOS SPDT Switch | Analog Devices

The Analog Devices MAX319CSA+ is a precision, single-pole double-throw CMOS analog switch with one normally open and one normally closed path, a maximum on-resistance of 35Ω, and an 8-pin SOIC package. It is designed for precision signal routing where low on-resistance, low charge injection, low power consumption, and high electrostatic-discharge withstand are important. An analog switch is a semiconductor interface that routes an analog signal between circuit nodes under digital control. Unlike a relay, it operates electronically at low voltage and can switch signals rapidly without mechanical wear. The MAX319 belongs to the broader analog-switch hierarchy, which sits alongside multiplexers, demultiplexers, and interface ICs used to connect sensors, test equipment, measurement systems, and signal-processing electronics. Key electrical characteristics include on-resistance below 20Ω typical and 35Ω maximum, guaranteed channel matching within 2Ω, and on-resistance variation of no more than 3Ω maximum across the analog signal range. Charge injection is low at 10pC, while power consumption is 35µW. These characteristics help preserve signal fidelity when the switch is used in measurement, control, or data-acquisition paths. The MAX319 family uses an improved silicon-gate CMOS process and rail-to-rail analog signal handling capability associated with a 44V maximum breakdown voltage. Its precision configuration is useful when signal-source impedance, leakage, or switch resistance could otherwise influence the measurement result. The MAX319CSA+ ordering code identifies the 8-pin SOIC package and the manufacturer's standard production configuration. Typical uses include battery-powered instrumentation, automated test equipment, analog measurement systems, signal-path routing, sample-and-hold circuits, and industrial control interfaces. Its low 35µW power consumption is particularly useful in portable equipment, while the 35Ω maximum on-resistance is suitable for moderate-impedance analog signals rather than ultra-low-impedance precision dividers. When designing a circuit around the MAX319CSA+, account for the switch's on-resistance, leakage, charge injection, and off-state behavior when calculating signal attenuation and timing. Place the device close to sensitive signal paths, maintain adequate grounding, and use the manufacturer pin-description table when assigning PCB tracks. Verify the logic levels and control polarity against the actual device documentation before finalizing the layout. This product page combines the manufacturer's device specifications with practical design guidance, package information, sourcing details, and a conservative drop-in assessment. It emphasizes verified distinctions between electrically similar devices so engineers can determine whether a replacement preserves both the board footprint and the required switch behavior.

詢價 聯絡我們
MAX3221CAE+ - 3 to 5.5V RS-232 Transceiver | Analog Devices
MAX3221CAE+

MAX3221CAE+ - 3 to 5.5V RS-232 Transceiver | Analog Devices

Analog Devices MAX3221CAE+ is a one-driver, one-receiver RS-232 transceiver designed for +3V to +5.5V operation and supplied in a 16-pin SSOP package. It provides 1 µA supply current when AutoShutdown is active, while integrating the charge-pump circuitry required to generate RS-232-compatible driver levels from a low-voltage supply. The MAX3221CAE+ is suitable for portable equipment, industrial controls, data acquisition systems, and other equipment that requires a compact, low-power serial interface. An RS-232 transceiver is an interface IC that combines a transmitter and receiver for communicating between a logic-level device and an RS-232 port. The transmitter converts low-voltage TTL or CMOS signals into RS-232 levels, while the receiver converts incoming RS-232 signals back into logic-compatible levels. The MAX3221 family belongs to the interface IC hierarchy and provides a practical way to bridge modern embedded systems with legacy RS-232 equipment. The MAX3221CAE+ includes Maxim's AutoShutdown feature, allowing the on-board power supply and driver circuitry to shut down when the receiver does not detect a valid signal. According to the Analog Devices MAX3221 product page, the device operates from +3V to +5.5V and reaches a supply current of 1 µA. These characteristics are particularly valuable in battery-powered instruments where a permanently active RS-232 interface would increase standby power consumption. The MAX3221 is a 1-driver/1-receiver 16-pin SSOP version of the 2-driver/2-receiver MAX3223. Its integrated RS-232 supply uses charge-pump circuitry to develop the voltage swing needed by the transmitter. The C designation denotes the family's capacitor configuration, while the E designation provides shutdown-control functionality. The A suffix identifies the package and temperature-related ordering configuration used in the MAX3221CAE+ ordering code. Typical applications include battery-powered test equipment, handheld configuration tools, serial adapters, industrial instrumentation, point-of-sale equipment, and embedded systems that must communicate with a host computer through an RS-232 port. The 16-pin SSOP footprint is useful for compact designs, although engineers should verify connector protection, cable length, logic levels, and supply compatibility against the system requirements. The principal design consideration is signal integrity. RS-232 is a single-ended, unbalanced interface, so cable routing and ground quality can materially affect noise immunity. Place the transceiver close to the interface connector, provide a low-impedance ground path, use suitable protection for exposed cables, and observe the manufacturer's recommended charge-pump capacitor values. External circuitry may also be required for hardware handshaking or for conditioning signals on long or electrically noisy cables. This page organizes the MAX3221CAE+ specifications, application guidance, package information, and verified same-package alternatives into an engineering-focused reference. It also highlights the practical trade-offs among shutdown, supply-voltage, capacitance, and temperature variants so designers can make a replacement decision based on actual circuit requirements rather than package similarity alone.

詢價 聯絡我們
MAX3221CAE+T - 1/1 RS-232 Transceiver | Analog Devices
MAX3221CAE+T

MAX3221CAE+T - 1/1 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221CAE+T is a one-driver, one-receiver RS-232 transceiver with AutoShutdown, operating from a 3 V to 5.5 V supply and drawing 1 µA when the charge-pump circuit is inactive. The device is packaged in a 16-pin SSOP and is designed for compact, low-power serial-interface equipment. Its principal characteristics are one RS-232 driver, one RS-232 receiver, 3 V to 5.5 V operation, and automatic supply shutdown when no valid receiver signal is detected. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the product hierarchy, the MAX3221 belongs to the RS-232 transceiver class of interface ICs, which sits between computer serial ports or control equipment and external communication links. The MAX3221 is the one-driver, one-receiver member of the MAX3221 family and is smaller than two-channel RS-232 transceivers such as the MAX3223. AutoShutdown is the device's principal power-management feature. When the receiver does not detect a valid signal level, the onboard power supply and driver shut down, reducing supply current to 1 µA as stated on the manufacturer product page. This behavior is valuable in battery-powered or intermittently connected equipment because a permanently connected serial port no longer needs to retain a full charge-pump load when communication is inactive. The 3 V to 5.5 V supply range supports integration with both 3.3 V and 5 V system rails. The MAX3221 integrates the RS-232 line driver, receiver, and onboard charge-pump circuitry in one compact package. This integration eliminates a separate external power-supply circuit while providing the voltage conversion required by the RS-232 interface. Unlike designs requiring a ±12 V supply, the MAX3221 generates RS-232-compatible levels from a single low-voltage supply. Its 16-SSOP construction supports conventional surface-mount assembly while conserving board area in embedded control, industrial, and communications systems. Typical applications include single-port serial-control links in industrial equipment, point-of-sale terminals, data-acquisition systems, instrumentation, and battery-operated peripherals. In each case, the device handles one unidirectional data path with the driver and the opposite direction with the receiver. Because it provides only one driver and one receiver, a design needing two physical RS-232 channels should evaluate a two-channel transceiver rather than adding a second MAX3221 unnecessarily. The primary design consideration is external bypass capacitance. Place the supply bypass capacitor and charge-pump capacitor close to their associated pins, with short ground paths to reduce supply disturbance and improve interface stability. Confirm the external capacitor values and connection details in the manufacturer datasheet before layout release, especially in designs operating from 3.3 V where charge-pump headroom and startup behavior affect system margins. This page combines the manufacturer product information with practical interface guidance, structured specifications, verified pin-compatible family alternatives, and design considerations that help engineers evaluate the MAX3221CAE+T for low-power RS-232 implementations.

詢價 聯絡我們
MAX3221CAE+TG1Z - 1/1 RS-232 Transceiver | Analog Devices
MAX3221CAE+TG1Z

MAX3221CAE+TG1Z - 1/1 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221CAE+TG1Z is a single-driver, single-receiver RS-232 line transceiver designed for true +3V to +5.5V operation. It provides one driver and one receiver in a 16-pin SSOP package, supports the full RS-232 interface standard, and draws only 1 µA through the AutoShutdown feature when no valid receiver signal is detected. The commercial-temperature, tape-and-reel ordering designation is MAX3221CAE+TG1Z. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into CMOS-compatible logic. The MAX3221 belongs to the hierarchy of RS-232 interface transceiver, serial interface IC, interface controller, and semiconductor. It is intended for equipment that needs bidirectional or unidirectional point-to-point serial connectivity without relying on a modern multi-standard transceiver family. The principal features of the MAX3221 include one RS-232 driver, one RS-232 receiver, operation from 3V to 5.5V, and a 1 µA AutoShutdown supply current. AutoShutdown reduces supply demand when the receiver does not detect a valid signal level. This makes the device useful in portable equipment and systems where a permanently connected serial port would otherwise waste power. Its 16-terminal gull-wing SSOP construction supports compact surface-mount assemblies. The device uses Maxim's low-power RS-232 interface architecture to support systems that cannot tolerate excessive supply current. The on-board charge-pump and driver circuitry provide the voltage swings required by RS-232 while the receiver converts the line-level input into a digital output. Designers should still account for the voltage difference between logic-side ground and the RS-232 line reference when integrating the device with another circuit board. Typical uses include industrial serial adapters, test equipment, data acquisition modules, point-of-sale terminals, instrument-control links, and legacy peripheral interfaces. The MAX3221 is especially appropriate where a compact single-channel interface is required rather than the multiple drivers and receivers offered by larger RS-232 families. For battery-powered instruments, its 1 µA shutdown current can reduce standby consumption. A key design consideration is ensuring that the logic supply, charge-pump capacitors, driver connection, receiver input, and signal ground are routed according to the manufacturer application guidance. Keep the interface connector and transceiver return path together where practical, and use suitable protection for exposed cables. Review the manufacturer's pin description and application circuit before assigning the 16 SSOP terminals or selecting external bypass capacitors. This product record combines the official MAX3221 family information, exact package attributes, commercial sourcing information, pin-compatible alternatives, comparison parameters, and application guidance to support component selection and board-level implementation.

詢價 聯絡我們
MAX3221CDB - 250kbps RS-232 Transceiver | Texas Instruments
MAX3221CDB

MAX3221CDB - 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3221CDB is a 3 V to 5.5 V, single-channel RS-232 line driver and receiver supporting data rates up to 250 kbps in a 16-pin SSOP package. The transceiver combines one driver, one receiver with a dedicated enable input, and a dual charge-pump circuit, while providing ±15 kV ESD protection on the serial-port connection pins, including ground. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a RS-232 serial link. The MAX3221 belongs to the line-driver and line-receiver hierarchy within interface ICs and interface transceivers. It is useful where a compact embedded system must communicate with legacy serial equipment, industrial controllers, service consoles, or other RS-232 endpoints without using a higher-voltage ±5 V supply rail. Key electrical features include a 3 V to 5.5 V supply range, operation at up to 250 kbps, one full-duplex driver, one full-duplex receiver, and ±15 kV ESD protection. The integrated dual charge-pump circuit provides the RS-232 level-shifting function needed by the line driver, while the receiver provides inversion and thresholding appropriate for noisy serial environments. A dedicated receiver-enable input supports controlled receiver operation in systems where the serial line must be disabled temporarily. The MAX3221 architecture is intended for low-voltage systems that cannot conveniently support a traditional RS-232 supply. Operating the charge-pump and transceiver from 3 V to 5.5 V reduces system-voltage requirements, while the single-channel structure avoids the channel count and pin requirements of multi-driver RS-232 devices. The 16-pin SSOP package is suitable for compact industrial, communications, instrumentation, and embedded-control equipment. Typical applications include RS-232 configuration ports, programmable-instrument control, industrial serial adapters, point-of-sale equipment, and maintenance interfaces. Its 250 kbps capability is more than adequate for many legacy control protocols, while the receiver enable function is useful in systems that share, isolate, or periodically disconnect a serial port. A key design consideration is that the external RS-232 connector, cable, and ground path determine much of the real-world ESD and noise immunity. Place the transceiver close to the connector, route the interface ground appropriately, and use the datasheet-recommended charge-pump capacitor and driver-load arrangements to preserve signal integrity. This page consolidates the device specifications, pin-compatible family comparisons, application guidance, and design cautions needed to evaluate the MAX3221CDB alongside other single-channel RS-232 transceivers.

詢價 聯絡我們
MAX3221CDBR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3221CDBR

MAX3221CDBR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)

Texas Instruments MAX3221CDBR is a 3 V to 5.5 V, single-channel RS-232 line driver and receiver supporting data rates up to 250 kbps in a 16-pin SSOP package. The transceiver combines one driver, one receiver with a dedicated enable input, and a dual charge-pump circuit, while providing ±15 kV ESD protection on the serial-port connection pins, including ground. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and a RS-232 serial link. The MAX3221 belongs to the line-driver and line-receiver hierarchy within interface ICs and interface transceivers. It is useful where a compact embedded system must communicate with legacy serial equipment, industrial controllers, service consoles, or other RS-232 endpoints without using a higher-voltage ±5 V supply rail. Key electrical features include a 3 V to 5.5 V supply range, operation at up to 250 kbps, one full-duplex driver, one full-duplex receiver, and ±15 kV ESD protection. The integrated dual charge-pump circuit provides the RS-232 level-shifting function needed by the line driver, while the receiver provides inversion and thresholding appropriate for noisy serial environments. A dedicated receiver-enable input supports controlled receiver operation in systems where the serial line must be disabled temporarily. The MAX3221 architecture is intended for low-voltage systems that cannot conveniently support a traditional RS-232 supply. Operating the charge-pump and transceiver from 3 V to 5.5 V reduces system-voltage requirements, while the single-channel structure avoids the channel count and pin requirements of multi-driver RS-232 devices. The 16-pin SSOP package is suitable for compact industrial, communications, instrumentation, and embedded-control equipment. Typical applications include RS-232 configuration ports, programmable-instrument control, industrial serial adapters, point-of-sale equipment, and maintenance interfaces. Its 250 kbps capability is more than adequate for many legacy control protocols, while the receiver enable function is useful in systems that share, isolate, or periodically disconnect a serial port. A key design consideration is that the external RS-232 connector, cable, and ground path determine much of the real-world ESD and noise immunity. Place the transceiver close to the connector, route the interface ground appropriately, and use the datasheet-recommended charge-pump capacitor and driver-load arrangements to preserve signal integrity. This page consolidates the device specifications, pin-compatible family comparisons, application guidance, and design cautions needed to evaluate the MAX3221CDBR alongside other single-channel RS-232 transceivers.

詢價 聯絡我們
MAX3221CDBRG4 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3221CDBRG4

MAX3221CDBRG4 - 250kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3221CDBRG4 is a single-channel RS-232 line driver and receiver with a 3 V to 5.5 V supply, 250 kbit/s operation, and ±15 kV ESD protection, housed in a 16-pin SSOP package. The transceiver integrates one driver, one receiver with a dedicated enable input, and a dual charge-pump circuit for generating the bipolar voltage levels required by RS-232. An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a RS-232 link. Within the signal-chain hierarchy, it belongs to the RS-232 interface, line-driver and receiver, communications-interface, and semiconductor categories. The MAX3221CDBRG4 is intended for equipment that needs one bidirectional serial port while operating from a 3 V to 5.5 V system supply. Key features include a maximum data rate of 250 kbit/s, ±15 kV ESD protection on the serial-port connection pins, and a low shutdown supply current. According to the manufacturer datasheet, the device provides AutoShutdown operation and supports true +3 V to +5.5 V supplies. Its integrated charge pumps reduce the external component count compared with a discrete RS-232 interface implementation. The MAX3221 family combines a driver and receiver with internal level-shifting circuitry. The charge-pump section develops positive and negative voltage rails from the single device supply, allowing the line interface to produce RS-232-compatible output levels. The receiver converts the bipolar serial signal back to a logic-compatible signal, while the dedicated receiver-enable control can place the receiving path in a reduced-power state when it is not required. Typical uses include industrial serial-port adapters, point-to-sale equipment, test and measurement instruments, embedded control systems, and legacy peripheral connections. The single-channel arrangement is especially suitable for compact systems that need one RS-232 port but no multi-port RS-232 expansion. When designing around the MAX3221CDBRG4, preserve the charge-pump capacitor and bypass-capacitor placement recommended in the manufacturer datasheet. Confirm that the host interface uses the correct logic voltage and that the receiver-enable polarity matches the controller firmware. The 16-pin SSOP footprint also requires careful solder-joint inspection because lead pitch and package density can complicate rework. This product page consolidates the electrical limits, interface function, packaging information, and practical design considerations for the MAX3221CDBRG4. It also identifies verified drop-in alternatives and organizes the selection trade-offs by speed, supply range, temperature grade, and interface configuration.

詢價 聯絡我們
MAX3221CPW - 250kbps Single-Channel RS-232 Transceiver | TI
MAX3221CPW

MAX3221CPW - 250kbps Single-Channel RS-232 Transceiver | TI

Texas Instruments MAX3221CPW is a single-channel RS-232 line driver/receiver with a 3 V to 5.5 V supply, operation up to 250 kbit/s, and ±15 kV ESD protection on the serial-port connection pins. The device is packaged in a 16-pin TSSOP package and includes one line driver, one line receiver with a dedicated enable pin, and a dual charge-pump circuit. It is designed to provide the electrical interface between an asynchronous communication controller and a serial-port connector while operating from a single supply voltage. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 voltage levels and converts received RS-232 signals back into logic-level signals. The MAX3221 belongs to the RS-232 interface IC hierarchy, which includes line drivers, line receivers, and charge-pump-assisted transceivers used for serial communications equipment, industrial controls, instrumentation, and point-of-sale terminals. The dual charge-pump circuit generates the positive and negative voltage levels required by the RS-232 interface without requiring a separate negative supply. The MAX3221 operates from 3 V to 5.5 V, accepts 5 V logic input with a 3.3 V supply, and supports data rates to 250 kbit/s. Its low standby current of 1 µA typical and use of external 0.1 µF capacitors help support compact, power-conscious interface designs. The dedicated receiver enable pin allows the receiver to be disabled when the host does not need to monitor the serial link. The device meets TIA/EIA-232-F requirements and is also associated with ITU V.28 operation, providing a standard RS-232 electrical interface for asynchronous communication systems. The ±15 kV ESD protection is specified pin to pin, including the serial-port connection pins and ground. This protection helps improve system robustness when cables are exposed to electrostatic discharge during installation, servicing, or normal handling. Typical uses include single-channel serial console links, industrial serial adapters, programmable instrument interfaces, barcode and point-of-sale equipment, and embedded systems that require one bidirectional RS-232 channel. The 250 kbit/s capability is appropriate for legacy serial peripherals and control links, while the 3 V to 5.5 V operating range supports both 3.3 V and 5 V system rails. When laying out the circuit, place the charge-pump capacitors and the driver and receiver interface capacitors close to their associated pins, and route the RS-232 traces away from sensitive analog or high-speed digital signals. Confirm that the transceiver enable state matches the host controller’s serial-port requirements before relying on low-power standby operation. This page combines the manufacturer’s RS-232 interface specifications with package and application guidance, verified comparison candidates, and practical design notes for engineers evaluating the MAX3221CPW in compact serial-interface designs.

詢價 聯絡我們
MAX3221CPWE4 - 3-5.5V Single RS-232 Transceiver | Texas Instruments
MAX3221CPWE4

MAX3221CPWE4 - 3-5.5V Single RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3221CPWE4 is a single-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply. The device provides one transmit channel, one receive channel, integrated charge-pump circuitry, and ±15 kV ESD protection in a 16-pin TSSOP package measuring 4.40 mm wide. Its interface operates at the voltage levels required by RS-232 while the low-voltage supply supports modern embedded systems. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts incoming RS-232 signals back into logic-level voltages. In the broader semiconductor hierarchy, the MAX3221CPWE4 belongs to the interface IC family and provides the physical signaling layer between a host controller and a serial peripheral. The integrated dual charge pump generates the positive and negative voltage levels required by the RS-232 standard without external discrete capacitors. The principal electrical characteristics visible in the manufacturer documentation include a 3 V to 5.5 V operating supply, single-channel driver and receiver operation, and ±15 kV ESD protection. The single-channel arrangement reduces board area and power consumption compared with multi-channel RS-232 transceivers. The 16-pin TSSOP package is also compatible with surface-mount manufacturing and supports compact serial-interface implementations. The MAX3221CPWE4 uses an RS-232 line driver to convert TTL-compatible transmit data into bipolar line signaling and an RS-232 receiver to recover logic-compatible receive data. A dedicated receiver-enable function provides control over the receive path. Internal dual charge-pump circuitry supports the positive and negative voltage swings associated with RS-232 signaling while operating from a single low-voltage supply. Typical applications include industrial serial-port equipment, data-acquisition systems, service-console interfaces, programmable instrumentation, and embedded control systems that need a compact RS-232 connection. It is particularly suitable when the logic system operates from 3.3 V or 5 V and an RS-232 port must be added without designing a separate high-voltage transmitter circuit. A critical implementation consideration is the distinction between the low-voltage supply and the bipolar voltages generated on the RS-232 side. Decoupling must be placed close to the supply pins, and external charge-pump capacitors must follow the values and layout guidance in the manufacturer datasheet. The PCB should also provide appropriate isolation and return-path planning for the externally accessible serial connector. This product page consolidates the exact-orderable part information, operating limits, package details, replacement guidance, and design-focused guidance that engineers need when evaluating the MAX3221CPWE4. It also provides a structured comparison with same-footprint MAX3221 variants so that temperature-grade, suffix, and sourcing decisions can be made without confusing electrical equivalence with PCB compatibility.

詢價 聯絡我們
MAX3221CPWRE4 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3221CPWRE4

MAX3221CPWRE4 - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3221CPWRE4 is a single-channel RS-232 line driver and receiver with a dual charge-pump circuit, a 3 V to 5.5 V supply range, operation up to 250 kbit/s, and ±15 kV ESD protection on the serial-port connection pins. It is packaged in a 16-pin TSSOP and includes a receiver with a dedicated enable input. The device provides the electrical interface between TTL-compatible logic and an RS-232 port while requiring external charge-pump capacitors of 0.1 µF. An RS-232 transceiver is an interface IC that converts low-voltage digital logic levels into the positive and negative voltage swings used by RS-232 equipment. In the broader semiconductor hierarchy, the MAX3221 belongs to the interface IC family, where line drivers and line receivers bridge computer, industrial-control, instrumentation, and communications equipment. Its single-channel architecture is useful when a system needs one bidirectional RS-232 connection rather than the multiple channels found on multi-channel transceiver families. The MAX3221 operates from 3 V to 5.5 V and accepts 5 V logic input when operated from a 3.3 V supply. Its 250 kbit/s data rate supports legacy serial-port, point-to-point control, and embedded equipment links. Pin-to-pin ESD protection of ±15 kV applies to the RS-232 connection pins, including ground, helping protect the interface against electrostatic discharge encountered during installation or handling. Internally, the device combines one line driver, one line receiver with a dedicated enable input, and a dual charge-pump circuit. The charge pumps generate the positive and negative voltages required for compliant RS-232 signaling. The receiver enable function allows a system to place the receive side in a controlled state, while the low standby current supports power-conscious designs where the interface must remain present without continuously receiving data. Typical uses include single-port RS-232 equipment interfaces, industrial controller serial links, programmable-instrument connections, and embedded systems that communicate with legacy peripherals. Because the logic side operates from 3 V to 5.5 V, the device can be used in both 3.3 V and 5 V systems. The 16-pin TSSOP also supports compact board layouts where a larger multi-channel transceiver would be unnecessary. Designers should place the 0.1 µF charge-pump capacitors close to their designated pins and observe the connector-side voltage and polarity requirements of RS-232. The interface does not create isolation, so an exposed or long cable run may require additional surge and ground-management measures. Input and output logic levels must also be checked against the connected controller rather than assumed from the serial-port standard. This page organizes the technical specifications, source links, interface applications, drop-in alternatives, and PCB considerations for engineers evaluating the MAX3221CPWRE4. It also distinguishes exact electrical matches from variants that change package details or feature sets, helping prevent a nominal substitution from creating an unintended PCB or firmware incompatibility.

詢價 聯絡我們
MAX3221CUE+ 3V-5.5V RS-232 Transceiver | Analog Devices
MAX3221CUE+

MAX3221CUE+ 3V-5.5V RS-232 Transceiver | Analog Devices

Analog Devices MAX3221CUE+ is a production RS-232 transceiver for single-driver, single-receiver communications links. It operates from +3V to +5.5V and is specified for EIA/TIA-232 and V.28/V.24 interfaces. The device includes one line driver, one receiver with a dedicated enable input, and a dual charge-pump circuit that supplies the RS-232 bipolar signal levels required by the communications interface. The MAX3221 family also uses Maxim’s AutoShutdown feature, allowing the on-board supply and drivers to shut down when no valid receiver signal is present, reducing supply consumption in systems where the interface is intermittently active. The MAX3221CUE+ is packaged in a 16-pin TSSOP and is identified by the C suffix and E-grade temperature designation in the manufacturer’s product family documentation. An RS-232 transceiver is an interface IC that translates between single-ended logic-level signals and the voltage-defined, bipolar signaling used by RS-232 equipment. In the transmit direction, the line driver converts logic-level data into an RS-232 signal; in the receive direction, the receiver converts the incoming RS-232 signal into a logic-level output. The dual charge-pump circuit supports the voltage translation required by the RS-232 standard without requiring a separate negative supply. The receiver enable pin gives the system designer a way to control whether the receiver is active, while AutoShutdown provides an additional power-management mechanism for ports that may be idle. The key verified characteristics of the MAX3221CUE+ include its +3V to +5.5V supply range, 1 µA-class shutdown current as described by the manufacturer family documentation, RS-232 transceiver operation, and its 16-pin TSSOP package. The Newark distributor listing identifies the part as an RS-232 transceiver with 120 Kbps signaling and a 70°C operating-temperature listing. The Analog Devices product page identifies the MAX3221 family as production and lists a starting list price of $2.52. Additional operating, electrical, and environmental details are available in the manufacturer datasheet and should be confirmed against the specific ordering code before design release. Typical uses include legacy serial-port equipment, industrial control links, data-acquisition equipment, and embedded systems that require a compact RS-232 port. The MAX3221CUE+ can be used when a design needs a low-voltage digital supply while retaining conventional RS-232 signaling at the connector. Its single-driver and single-receiver organization is appropriate for point-to-point links rather than multi-drop RS-232 networks. The dedicated receiver enable and AutoShutdown functions are useful in systems where the interface must remain available without continuously powering the complete driver and receiver circuitry. The primary design consideration is verifying the exact pinout, capacitor values, and signal-termination requirements from the MAX3221 manufacturer datasheet. Charge-pump capacitors must be placed close to their associated pins, and the RS-232 connector-side circuit should be designed for the voltage and ESD requirements of the application. The MAX3221CUE+ is appropriate when the required interface is one driver and one receiver in a 16-pin TSSOP footprint; designers needing multiple drivers or receivers should select a larger RS-232 transceiver family instead. This page combines manufacturer family information, distributor pricing, verified cross-reference results, application guidance, and design cautions to support practical sourcing and comparison of the MAX3221CUE+ rather than reproducing only the basic distributor description.

詢價 聯絡我們
MAX3221CUE+T - 3V RS-232 Transceiver | Analog Devices
MAX3221CUE+T

MAX3221CUE+T - 3V RS-232 Transceiver | Analog Devices

Analog Devices MAX3221CUE+T is a one-driver, one-receiver RS-232 transceiver designed for operation from a 3.0 V to 5.5 V single supply. The device combines a dual charge-pump supply, automatic shutdown, and a low-dropout line driver in a 16-pin TSSOP package. Its RS-232 line-driver output and receiver input are intended for serial-port connections, while the integrated charge pumps generate the bipolar voltage required to transmit RS-232 signals from a low-voltage supply. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts incoming RS-232 signals into logic-level inputs. In the product hierarchy, the MAX3221 belongs to the RS-232 transceiver class, interface IC category, and broader semiconductor family. It is appropriate where a modern controller operates from 3.0 V or 5.0 V but the attached equipment still uses the voltage range and signaling conventions of the RS-232 standard. The MAX3221 uses AutoShutdown to reduce supply consumption when no valid receiver signal is detected. According to the manufacturer, this feature can reduce onboard supply and driver current to approximately 1 µA when the receiver inputs are inactive. The MAX3221CUE+T ordering code identifies the temperature-range and package configuration, while the +T suffix denotes the tape-and-reel shipping format shown for this part. Internally, the proprietary dual charge-pump circuit produces the elevated voltage used by the driver from one 3.0 V to 5.5 V supply. This architecture avoids a separate negative power rail in equipment using a single positive supply. The receiver converts the RS-232 input into CMOS-compatible logic, and the driver presents the required RS-232 output levels to the connector-side interface. Typical uses include industrial control panels, point-of-sale terminals, serial adapters, embedded instrumentation, and service equipment that must connect a low-voltage processor to an RS-232 port. The 16-pin TSSOP package also suits compact boards where connector spacing and component height are important. The AutoShutdown behavior is particularly useful in battery-powered or intermittently connected portable systems. Layout should place charge-pump capacitors and interface-path components close to the device, keep the RS-232 traces away from sensitive analog and high-speed digital nets, and provide a low-impedance ground return. The external interface must also satisfy the applicable RS-232 voltage, grounding, and ESD requirements. Because this integrated circuit generates only a small number of RS-232 channels, a multiport design may require multiple transceivers or a higher-channel-count device. This product page combines the manufacturer specifications, package information, RS-232 application context, practical layout guidance, and a pin-compatible comparison focused on helping engineers determine whether the MAX3221CUE+T can be used without redesigning an existing 16-pin TSSOP circuit.

詢價 聯絡我們
MAX3221EAE+ - 3V RS-232 Transceiver with AutoShutdown | Analog Devices
MAX3221EAE+

MAX3221EAE+ - 3V RS-232 Transceiver with AutoShutdown | Analog Devices

The Analog Devices MAX3221EAE+ is a 3V-powered, 1-driver/1-receiver RS-232 transceiver with AutoShutdown, operating from 3V to 5.5V and reaching 120 kbps in a 16-pin SSOP package. It provides one transmit driver, one receive path, automatic shutdown and wake-up, and enhanced ESD protection according to the verified manufacturer description. The device is intended for low-voltage serial interfaces where power efficiency, compact footprint, and reliable RS-232 signal translation are required. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 links. The MAX3221 family uses an internal charge-pump circuit to generate the RS-232 transmitter voltage from a single low-voltage supply. In the system hierarchy, it is a communication interface IC, a line-interface device, and a voltage-level translator used between host controllers and external serial equipment. Key verified characteristics include a 3V to 5.5V supply range, 120 kbps data-rate capability, 1 microamp supply-current operation in shutdown, one RS-232 driver, and one receiver. AutoShutdown reduces power use when the receiver does not detect a valid signal. The 16-SSOP package is specified as approximately 5.30 mm wide in the distributor result, making the device suitable for compact equipment designs. The MAX3221EAE+ is appropriate for embedded serial-console connections, industrial control links, point-of-sale systems, instrumentation, and USB-to-RS-232 adapters. The internal charge pump removes the need for a separate bipolar supply, while the receiver and driver provide the basic signal path between a low-voltage controller and an RS-232 connector. The tradeoff is that RS-232 is a single-ended, point-to-point interface with limited cable distance and no multidrop capability. For layout, place charge-pump capacitors and the receiver/transmitter interface components close to their associated pins, and follow the manufacturer's recommended capacitor values. Keep the RS-232 connector-side traces away from sensitive low-level logic where practical. Confirm line rates, cable length, ground continuity, and the system supply level before finalizing the design. This page combines the verified manufacturer description, distributor package information, application guidance, and comparison-oriented design notes to provide practical RS-232 transceiver information beyond a basic catalog listing.

詢價 聯絡我們
MAX3221EAE+T - 3V RS-232 Transceiver | Analog Devices
MAX3221EAE+T

MAX3221EAE+T - 3V RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221EAE+T is a 1-driver, 1-receiver RS-232 transceiver with a 3 V to 5.5 V single-supply range, AutoShutdown behavior, and enhanced electrostatic-discharge protection. It is packaged in a 16-pin SSOP and is intended for systems that require a single power rail while exchanging data with an RS-232-compatible equipment. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received line-level signals back into logic levels. The MAX3221 belongs to the broader RS-232 interface, communication interface, and interface IC hierarchy. Its integrated charge-pump supply generates the bipolar voltage required by the RS-232 transmitter, allowing operation from a single low-voltage supply rather than a separate positive and negative power rail. The MAX3221E family features automatic shutdown and wake-up behavior. When no valid signal is detected at the receiver inputs, the on-board power supply and drivers can shut down, reducing supply current to approximately 1 µA according to the manufacturer product information. This behavior is useful in battery-powered and intermittently connected equipment because the interface does not need to remain fully powered between communication sessions. The E version adds enhanced electrostatic-discharge protection. The manufacturer lists ±15 kV ESD protection for the MAX3221E, while the MAX3221 product family is designed for EIA/TIA-232 and V.28/V.24 communications. The MAX3221E product page also identifies IEC 61000-4-2 ESD protection for the RS-232 pins. These ratings should be evaluated against the connector placement and system grounding strategy rather than treated as a substitute for external surge protection. Typical uses include industrial serial-port equipment, point-of-sale terminals, data acquisition equipment, configuration interfaces, and legacy peripheral connectivity. The 16-pin SSOP footprint suits compact designs where space is constrained, although connector routing and exposed-charge-pump behavior still require careful PCB planning. The MAX3221E/MAX3223E/MAX3243E family is available from a 3 V supply, with the exact model selection determined by the required number of drivers and receivers. Designers should follow the manufacturer’s recommended charge-pump capacitor connections, place the four external capacitors close to their associated pins, and route the RS-232 traces away from sensitive analog and high-speed digital paths. Receiver and driver enable functions provide local control, while AutoShutdown can reduce power when the remote device is disconnected. The MAX3221EAE+T is therefore best suited to compact, single-supply RS-232 links that require automatic power saving and improved ESD resilience. This page combines the manufacturer family information with practical interface-selection guidance, package-specific implementation considerations, and qualified comparison options for engineers evaluating replacements for the MAX3221EAE+T.

詢價 聯絡我們
MAX3221EAE+TG1Z - 250kbps RS-232 Transceiver | Analog Devices
MAX3221EAE+TG1Z

MAX3221EAE+TG1Z - 250kbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3221EAE+TG1Z is a single-channel RS-232 transceiver with one driver and one receiver, 3 V to 5.5 V single-power operation, a maximum data rate of 250 kbps, and enhanced ±15 kV IEC ESD protection in a 16-pin SSOP package. The device also provides automatic shutdown and wakeup functions for power-conscious serial-interface designs. An RS-232 transceiver is an interface IC that converts logic-level signals between a computer or embedded controller and the voltage levels used by an RS-232 communications link. Within the interface hierarchy, the MAX3221EAE+TG1Z belongs to the RS-232 transceiver class, where it integrates the line driver, line receiver, charge-pump support, and low-power control functions needed to implement a complete single-channel serial port. Key operating characteristics include a 3 V to 5.5 V supply range, 250 kbps maximum signaling rate, and ±15 kV IEC ESD protection. The automatic shutdown and wakeup features help reduce supply consumption when the associated system is inactive. A low-power supply-current specification of 1 µA is associated with the MAX3221EAE family, supporting battery-operated and energy-conscious equipment designs. The MAX3221EAE+TG1Z uses the MAX3221E 1-driver/1-receiver architecture. Its 16-pin SSOP construction keeps the interface compact while providing the external components and connections required for RS-232 operation. The 250 kbps capability makes it suitable for moderate-speed control links, configuration ports, data acquisition equipment, and service interfaces that do not require modern multi-gigabit serial communication. Typical applications include industrial control and instrumentation, data acquisition systems, test and measurement equipment, embedded serial adapters, and point-of-sale or peripheral interfaces. Automatic shutdown is particularly useful in portable and remotely powered systems where the serial transceiver can remain present on the board without maintaining a continuously active internal state. The integrated ESD protection improves interface robustness when cables connect the board to external equipment. A key design consideration is the distinction between the logic-side supply and the RS-232 line-side operating requirements. Confirm capacitor selection, charge-pump operation, logic levels, and shutdown-control polarity against the manufacturer datasheet before layout release. Place the required charge-pump and bypass capacitors close to their designated pins, and keep the RS-232 connector and interface traces physically separated from sensitive analog or high-speed digital nets. This page consolidates the verified electrical identity, package details, interface characteristics, drop-in alternatives, and application guidance for the MAX3221EAE+TG1Z. It also highlights practical distinctions among same-family and cross-brand RS-232 interface options so engineers can select a part based on package fit, supply range, data rate, shutdown behavior, and protection requirements rather than by partial parameter similarity alone.

詢價 聯絡我們
MAX3221ECAE+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3221ECAE+T

MAX3221ECAE+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221ECAE+T is a single-driver, single-receiver RS-232 transceiver operating from 3.0V to 5.5V at up to 250kbps in a 16-pin SSOP package. It integrates a charge-pump voltage converter, automatic shutdown and wake-up, and ±15kV ESD protection for compact, low-power serial-interface designs. An RS-232 transceiver is a semiconductor interface that converts logic-level TTL or CMOS signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic levels. Positioned within the interface IC and power-management hierarchy, the MAX3221 supports point-to-point serial links in industrial control, instrumentation, data acquisition, and legacy peripheral equipment. The MAX3221 uses one transmitter and one receiver, making it suitable for serial links requiring a single bidirectional channel. Its 3.0V to 5.5V supply range permits operation from both 3.3V and 5V systems. AutoShutdown reduces supply current to approximately 1µA when the receiver detects no valid signal, helping conserve power in intermittently connected equipment. The integrated charge-pump circuitry develops the positive and negative voltages required by RS-232 without a separate power supply. Enhanced electrostatic-discharge protection is rated at ±15kV, an important consideration for exposed cables and connectors. The interface also operates at up to 250kbps, covering conventional asynchronous RS-232 communication rates while providing margin for modern firmware-based protocols. Typical uses include RS-232 configuration ports on industrial controllers, test and measurement equipment, POS terminals, serial adapters, and embedded systems communicating with legacy peripherals. Because RS-232 is a single-ended, unbalanced standard, cable routing and grounding remain important, and long cables should be treated as potential sources of noise and ESD events. Place the charge-pump capacitors and transceiver-side bypass capacitor close to their associated pins. Keep the RS-232 connector interface path physically separate from sensitive logic, and route the ground return appropriately for the installed cable. Verify baud-rate, logic-level, and supply compatibility before replacing another transceiver. This page combines the manufacturer's RS-232 interface specifications, package information, sourcing guidance, and practical implementation considerations. It also organizes pin-compatible alternatives and explains where their ESD, power-management, and temperature-grade differences matter during component selection.

詢價 聯絡我們
MAX3221ECDBR - 3V-5.5V 250kbps RS-232 | Texas Instruments
MAX3221ECDBR

MAX3221ECDBR - 3V-5.5V 250kbps RS-232 | Texas Instruments

The Texas Instruments MAX3221ECDBR is a 3V to 5.5V single-channel RS-232 line driver/receiver with 250kbps data-rate capability, ±15kV IEC ESD protection, and a 16-pin SSOP package. It provides the electrical interface between an asynchronous communications controller and an RS-232 port while operating from a 3V to 5.5V supply. An RS-232 transceiver is an interface IC that converts logic-level transmit and receive signals into RS-232-compatible line levels and converts incoming RS-232 signals back into logic levels. It belongs to the RS-232 interface transceiver category, connects digital controllers to serial ports, and belongs to the broader interface IC and semiconductor hierarchy. The MAX3221ECDBR integrates one driver and one receiver for a single RS-232 channel. Its principal operating characteristics include a 3V to 5.5V supply range, a maximum data rate of 250kbps, and ±15kV IEC ESD protection. The device is specified for a 0°C to 70°C operating-temperature range and is offered in a compact 16-pin SSOP package measuring approximately 0.209 inches, or 5.30mm, wide. These characteristics make it suitable for equipment that must generate or receive RS-232 signals from a low-voltage digital system. The MAX3221ECDBR is identified as a full RS-232 single-channel transceiver and is designed around the A/EIA-232-F interface requirements described by the manufacturer. Its integrated driver, receiver, charge-pump support components, and protection features reduce the external circuitry required around a conventional asynchronous serial controller. The 3V minimum supply operation permits use with modern 3.3V system logic without requiring a 5V-only interface rail. Typical uses include single-port RS-232 adapters, industrial serial controllers, point-of-sale equipment, test instruments, data-acquisition systems, and embedded equipment that still uses an RS-232 physical interface. In these systems, the IC receives logic-level serial data for transmission and converts a remote RS-232 signal into a logic-level receive signal. The 250kbps capability supports substantially faster asynchronous links than legacy low-speed serial ports. PCB design should preserve the pin assignments and decoupling recommendations in the manufacturer datasheet. Keep the charge-pump capacitor connections, driver and receiver traces, and exposed circuit paths compact, and provide suitable protection at an accessible connector because the internal ±15kV IEC ESD rating does not remove the need for an appropriate system-level surge and ESD strategy. This page combines the verified device identity, package information, operating limits, interface characteristics, replacement candidates, and application-specific design guidance to support component selection and PCB implementation without treating the manufacturer datasheet as a substitute for careful signal-integrity and protection review.

詢價 聯絡我們
MAX3221ECDBRG4 - 3V-5.5V Single RS-232 Transceiver | TI
MAX3221ECDBRG4

MAX3221ECDBRG4 - 3V-5.5V Single RS-232 Transceiver | TI

The Texas Instruments MAX3221ECDBRG4 is a 3 V to 5.5 V single-channel RS-232 line driver and receiver with ±15 kV IEC 61000-4-2 ESD protection, housed in a 16-SSOP package measuring 5.30 mm wide. The device combines one driver and one receiver in a compact interface suitable for bidirectional serial-port connections. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible voltage levels and restores incoming RS-232 signals to logic-compatible levels. It belongs to the interface IC hierarchy, where it connects digital logic or microcontrollers to legacy peripheral ports. The MAX3221E family also uses on-chip charge-pump circuitry to generate the bipolar voltage levels required by RS-232 without a separate negative supply. Key features include operation from 3 V to 5.5 V, one driver and one receiver, ±15 kV human-body-model ESD protection, ±8 kV IEC 61000-4-2 contact discharge protection, and ±15 kV air-gap discharge protection. The device uses four external 0.1 µF charge-pump capacitors. Its 16-SSOP surface-mount package supports compact industrial-control, instrumentation, and embedded equipment layouts. The MAX3221E architecture provides the electrical interface required by asynchronous serial systems. A single external capacitor at each charge-pump node supports the internal voltage conversion, while the driver presents the bipolar voltage levels expected by an RS-232 port and the receiver converts those levels back to digital logic. This integration simplifies PCB area compared with discrete level-shifting and charge-pump networks. Typical applications include debug-console connections, industrial serial adapters, point-of-sale equipment, test and measurement instruments, and embedded systems that retain an RS-232 port. For new designs, an RS-232 transceiver is most useful when an existing host or peripheral expects the physical RS-232 interface rather than USB, RS-485, or a proprietary differential link. Place the four 0.1 µF charge-pump capacitors close to their designated pins and route the driver output and receiver input traces away from sensitive analog or high-speed digital nodes. Confirm the board ground and cable shield arrangement before field deployment because connector-level ESD protection alone does not eliminate conducted noise entering through the cable. This product record combines the MAX3221ECDBRG4 electrical characteristics, package information, interface ratings, drop-in alternatives, comparison parameters, and practical layout guidance in one engineering-focused reference. It supports component selection, PCB footprint review, and RS-232 interface design without relying on a generic interface-IC overview.

詢價 聯絡我們
MAX3221ECPWG4 - 3V RS-232 Transceiver | Texas Instruments
MAX3221ECPWG4

MAX3221ECPWG4 - 3V RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3221ECPWG4 is a single-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply, with one driver, one receiver, and enhanced ±15 kV IEC ESD protection in a 16-pin TSSOP package. The MAX3221ECPWG4 is designed for compact serial-interface equipment requiring a single RS-232 channel and a low-voltage digital supply. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic levels. The MAX3221ECPWG4 belongs to the line-transceiver hierarchy within interface ICs. Its integrated charge-pump circuitry supports single-supply operation, while the driver and receiver provide the physical layer required to connect a host, controller, or embedded system to an RS-232 port. The device operates across a 3 V to 5.5 V supply range and includes one line driver and one line receiver. According to the manufacturer description, its RS-232 pins provide protection of ±15 kV under the IEC human-body model, ±8 kV under the IEC 61000-4-2 contact-discharge test, and ±15 kV under the IEC 61000-4-2 air-gap-discharge test. These ratings are intended for protecting exposed serial-port connectors against electrostatic discharge. The MAX3221ECPWG4 uses a 16-terminal gull-wing surface-mount package with a 0.65 mm terminal pitch. The package body is identified as 4.40 mm wide, and the manufacturer markets the device as a commercial-temperature-grade part. Its single-channel architecture makes it appropriate where only one transmit and one receive path is needed, avoiding the extra drivers, receivers, and package area associated with a multi-channel transceiver. Typical uses include single-port RS-232 console connections, industrial equipment interfaces, point-of-sale terminals, data-acquisition equipment, and service or configuration ports. The 3 V to 5.5 V operating range allows the transceiver to share power with 3.3 V or 5 V system logic, reducing the need for a separate 5 V-only interface supply in many designs. PCB design should preserve the manufacturer-recommended connection and bypass layout, place charge-pump capacitors close to their associated pins, and route the RS-232 driver outputs toward the connector. The communication lines should remain away from sensitive analog or high-speed digital traces where practical. Confirm every pin function and capacitor value against the manufacturer pin description and application schematic before releasing a layout. This product page combines the MAX3221ECPWG4 electrical ratings, package characteristics, RS-232 application context, and qualified drop-in alternatives with practical PCB and protection guidance. It is structured to help engineers identify whether the single-channel 16-pin TSSOP device fits a connector, industrial-control, or embedded serial-interface design.

詢價 聯絡我們
MAX3221ECPWR - 250kbps Single RS-232 Transceiver | Texas Instruments
MAX3221ECPWR

MAX3221ECPWR - 250kbps Single RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3221ECPWR is a 3 V to 5.5 V single-channel RS-232 line driver and receiver capable of signaling at 250 kbps, with plus or minus 15 kV ESD protection across the serial-port pins. It is packaged in a 16-pin TSSOP and includes one line driver, one line receiver with a dedicated enable function, and a dual charge-pump circuit. The MAX3221ECPWR provides the electrical interface between an asynchronous communication controller and a serial-port connector while meeting the requirements of TIA/EIA-232-F. An RS-232 transceiver is an interface IC that converts logic-level signals from a UART or microprocessor into RS-232 voltage levels and converts incoming RS-232 signals back into CMOS-compatible logic. The RS-232 interface belongs to the interface IC hierarchy, where it bridges digital controllers, embedded systems, industrial equipment, and external serial peripherals. The MAX3221E family is designed for single-channel links where a second driver and receiver would add cost and board area without improving the application. The device operates from a single 3 V to 5.5 V supply, making it suitable for both 3.3 V and 5 V systems. Its internal dual charge-pump circuit generates the positive and negative voltages required by the TIA/EIA-232-F interface without a separate bipolar supply. Data rates up to 250 kbps support legacy serial communication, industrial control links, data acquisition equipment, configuration ports, and service interfaces. Plus or minus 15 kV ESD protection strengthens the serial connector against electrostatic discharge. The receiver includes a dedicated enable function that can place the receiver in a high-impedance state, while the driver-side enable structure supports controlled interface operation. The MAX3221ECPWR combines these functions in a compact 16-pin TSSOP, allowing a complete RS-232 port to be implemented with a small PCB footprint. Its single-channel architecture is appropriate for point-to-point serial links rather than multi-drop RS-485 networks. Typical uses include industrial equipment interfaces, laboratory instrumentation, cash-register systems, embedded control panels, and legacy peripheral connections. The 250 kbps maximum data rate exceeds the throughput of many legacy RS-232 ports while retaining compatibility with established TIA/EIA-232-F designs. The 3 V to 5.5 V operating range also allows the same interface topology to be used across mixed-voltage systems. When laying out the circuit, place the charge-pump capacitors and supply bypass capacitor close to their corresponding pins, and route the driver output and receiver input away from noisy digital signals. Use the manufacturer datasheet pin-description table to verify signal assignments and the exposed ground connection before assigning PCB tracks.

詢價 聯絡我們
MAX3221ECTE+ - 3V/5V RS-232 Transceiver | Maxim Integrated
MAX3221ECTE+

MAX3221ECTE+ - 3V/5V RS-232 Transceiver | Maxim Integrated

The Maxim Integrated MAX3221ECTE+ is a 3 V to 5.5 V RS-232 transceiver supporting data rates up to 250 kbps in a 16-pin TQFN package measuring 5 mm by 5 mm. The device combines one RS-232 transmitter, one receiver, ±15 kV ESD protection, and automatic shutdown and wakeup functions in a single integrated interface IC. It is designed for compact equipment requiring a standards-compliant EIA/TIA-232 connection between a host UART and an external data cable. An RS-232 transceiver is an interface IC that converts logic-level UART signals into differential, bipolar RS-232 levels and converts received RS-232 levels back into logic-compatible signals. The MAX3221ECTE+ operates from a single 3.0 V to 5.5 V supply, making it suitable for systems using either 3.3 V or 5 V logic. Its automatic shutdown circuitry reduces supply demand when the interface is inactive, while wakeup support allows operation to resume when valid serial data arrives. The principal electrical features include a maximum data rate of 250 kbps, ±15 kV ESD protection, and a shutdown current of 1 µA. The integrated protection is particularly valuable in industrial control, instrumentation, and data-acquisition equipment where an RS-232 connector may be exposed to electrostatic discharge. The device also supports EIA/TIA-232 and V.28/V.24 communication requirements while presenting a compact, board-space-efficient interface to the host controller. MAX3221ECTE+ combines a transmitter and receiver in one package, avoiding separate logic-level conversion devices for each direction. The 5 mm by 5 mm TQFN footprint supports dense control boards, but its exposed pad requires careful PCB layout and adequate thermal dissipation. Charge-pump circuitry internally develops the positive and negative RS-232 voltage levels needed by the transmitter, so the application circuit requires the external components and connections specified by the manufacturer datasheet. Typical uses include industrial serial controllers, test and measurement equipment, POS terminals, embedded serial bridges, and isolated or long-distance RS-232 links. At 250 kbps, the interface is fast enough for moderate-speed telemetry and configuration traffic while maintaining compatibility with conventional RS-232 ports. For designs operating from 5 V, the wide 3.0 V to 5.5 V supply range also provides flexibility when the host uses a lower-voltage rail. Use the manufacturer pin description and application circuit when assigning the TQFN land pattern, connecting the exposed pad, and placing bypass or charge-pump capacitors. Keep the interface path away from sensitive analog signals, provide a low-impedance ground connection, and keep external cables and connectors as short as practical. ESD protection reduces connector risk but does not replace correct grounding, shielding, and surge-protection design. This page consolidates the device specifications, verified package information, sourcing guidance, drop-in alternatives, and practical RS-232 layout considerations. It also distinguishes the electrically useful alternatives from package or temperature options that require additional design review before substitution.

詢價 聯絡我們
MAX3221ECTE+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3221ECTE+T

MAX3221ECTE+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3221ECTE+T is a single-channel RS-232 transceiver rated for data rates up to 250 kbps, operating from a 3.0 V to 5.5 V supply in a 16-pin TQFN package. It provides ±15 kV ESD protection and uses the MAX3221 family AutoShutdown feature to reduce supply current to 1 µA when no valid receiver signal is detected. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals between a host or controller and a RS-232 port. Within the interface hierarchy, the MAX3221ECTE+T belongs to the RS-232 transceiver class, then to line-driver and line-receiver circuits, and ultimately to the broader communication-interface and semiconductor categories. Its charge-pump circuitry generates the bipolar voltage levels required by the RS-232 standard without a separate negative supply. Key features include a 250 kbps maximum data rate, a 3.0 V to 5.5 V operating range, ±15 kV ESD protection, and 1 µA shutdown supply current. The device provides one transmit channel and one receive channel, making it suitable for compact point-to-point serial links. AutoShutdown reduces power consumption when the receiver detects no valid RS-232 activity, while automatic wakeup permits the circuit to resume operation when a valid signal returns. The MAX3221 architecture integrates the transmitter, receiver, interface control, and charge-pump functions into one package. This consolidation simplifies PCB design by reducing the number of external interface components. The transmitter converts TTL/CMOS logic levels into RS-232 levels, while the receiver converts bipolar RS-232 inputs into a CMOS-compatible output. Internal protection and controlled slew behavior support reliable communication over cable connections exposed to electrostatic discharge. Typical applications include industrial serial consoles, data-acquisition equipment, point-of-sale terminals, test and measurement instruments, and embedded control systems that require an RS-232 port with automatic power management. The 3.0 V minimum supply voltage also makes the device suitable for mixed 3.3 V and 5 V systems when the interface requires full RS-232 electrical levels rather than TTL signaling. When laying out the circuit, place the charge-pump capacitors and the interface bypass capacitor close to their associated pins, and route the RS-232 connector traces away from sensitive analog or high-speed digital nets. Confirm the logic levels and polarity of the connected host because RS-232 is a single-ended, inverted bipolar interface and is not directly interchangeable with TTL UART signaling.

詢價 聯絡我們