產品(46,000+)

MAX3232EEWE+ - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEWE+

MAX3232EEWE+ - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EEWE+ is a dual-driver, dual-receiver RS-232 transceiver operating from 3.0V to 5.5V, supporting data rates up to 1Mbps in a 16-pin SOIC package. The device provides ±15kV ESD protection and a low-power design with shutdown current down to 10nA. It is a production-status, true RS-232 interface suitable for industrial control, instrumentation, data acquisition, and embedded serial communication systems. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 levels and converts incoming RS-232 signals back into logic-level signals. The MAX3232 belongs to the RS-232 transceiver family within interface ICs, where the dual-driver and dual-receiver arrangement provides two complete point-to-point serial channels. Its charge-pump-assisted implementation supports both 3.0V and 5.5V systems without requiring a negative supply. Key features include operation across a 3.0V to 5.5V supply range, data rates up to 1Mbps, ±15kV ESD protection, and shutdown current down to 10nA. Two transmitters and two receivers allow simultaneous bidirectional communication on separate RS-232 links. The 16-pin SOIC package supports conventional surface-mount PCB assembly, while the manufacturer designates the MAX3232 family as production and provides the associated data sheet with a revision number of 10. The MAX3232EEWE+ is identified as a full-duplex, 2/2 RS-232 transceiver. Its integrated charge-pump circuitry generates the voltage levels required by true RS-232, while the receiver side restores usable logic levels for the host controller. This combination allows a microcontroller, programmable logic controller, or UART-equipped processor to communicate with legacy RS-232 equipment through a compact two-channel interface. Typical uses include factory automation equipment, industrial sensors, barcode and test instruments, serial adapters, and embedded control boards. The 1Mbps capability is useful when a system needs more link bandwidth than conventional low-speed serial interfaces provide. The ±15kV ESD rating adds protection at connector-facing pins, although board-level grounding, shielding, and signal-routing practices remain necessary in electrically noisy installations. Designers should follow the manufacturer pin-description table when assigning connector and logic signals, and should place required charge-pump and bypass capacitors close to their designated pins. The unused driver output or receiver input should be handled according to the manufacturer guidance so that an unused channel does not float. Keep the RS-232 traces away from sensitive analog nodes and route chassis and signal-ground connections according to the system grounding strategy. This page combines the manufacturer's device identification with practical interface guidance, package details, sourcing information, and drop-in alternatives. It is intended to help engineers evaluate the MAX3232EEWE+ for a new RS-232 design or identify a compatible substitute for an existing 16-pin SOIC assembly.

詢價 聯絡我們
MAX3232EEWE+G1Z - 2/2 RS-232 Transceiver | Analog Devices
MAX3232EEWE+G1Z

MAX3232EEWE+G1Z - 2/2 RS-232 Transceiver | Analog Devices

Analog Devices MAX3232EEWE+G1Z is a 2/2 true RS-232 transceiver with two drivers and two receivers, operating from 3.0V to 5.5V and supporting data rates up to 1Mbps. The device is housed in a 16-pin SOIC package and provides ±15kV ESD protection on its RS-232 interface pins. Its low-power design operates down to 10nA, making it suitable for low-power serial equipment. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic-compatible signals. The MAX3232EEWE+G1Z belongs to the transceiver class of interface ICs, combining two transmit channels and two receive channels in one package. This integrated arrangement reduces board area and simplifies design of point-to-point serial links, industrial control equipment, data-acquisition systems, and service interfaces. Key features include a 3.0V to 5.5V supply range, operation at up to 1Mbps, ±15kV ESD protection, and a low-power specification extending down to 10nA. The 2/2 channel arrangement allows two serial links to be implemented with one package. Its true RS-232 implementation is intended for systems whose connected equipment uses unbalanced RS-232 signaling rather than differential RS-485 or RS-422. The transceiver translates between modern CMOS logic levels and the voltage levels used by RS-232 equipment. Because RS-232 uses positive and negative signal voltages, the interface requires appropriate charge-pump circuitry and external charge-pump capacitors. The Analog Devices datasheet provides the recommended capacitor values, electrical characteristics, timing information, and pin configuration needed to design the interface correctly. Typical applications include industrial serial controllers, test and measurement equipment, point-of-sale terminals, data loggers, instrument interfaces, and embedded systems communicating with legacy RS-232 peripherals. It is especially useful where two serial channels are required and a protected 16-pin SOIC footprint is preferable to larger transceiver packages. PCB layout should keep the charge-pump capacitor connections short, provide an uninterrupted ground path, and route RS-232 traces away from sensitive analog and high-speed digital circuits. External protection or filtering may be needed when cables are long, ports are frequently disconnected, or the interface is exposed to severe industrial transients. This product page combines the manufacturer interface information with practical selection, layout, and replacement guidance. It also distinguishes the verified electrical characteristics from parameters that require confirmation in the MAX3232E datasheet, helping engineers shorten component qualification without overlooking package and ordering-code differences.

詢價 聯絡我們
MAX3232EEWE+T - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEWE+T

MAX3232EEWE+T - 1Mbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3232EEWE+T is a dual-channel true RS-232 transceiver with one driver and one receiver per channel, supporting data rates up to 1Mbps. It operates from 3.0V to 5.5V, features ±15kV ESD protection, and provides a shutdown supply current as low as 10nA. The device is packaged in a 16-pin wide SOIC and supplied on tape and reel with the +T ordering suffix. A true RS-232 transceiver is an interface circuit that converts logic-level signals between a host or embedded controller and an RS-232 link. The MAX3232 family uses charge-pump circuitry to generate the positive and negative voltage levels required by true RS-232, while integrated level translation allows the logic-side interface to operate from a low-voltage supply. This makes the device useful at the boundary between modern microcontrollers, industrial controllers, and legacy serial equipment. Key features include a 3.0V to 5.5V operating range, operation up to 1Mbps, ±15kV ESD protection, and shutdown current down to 10nA. Each channel includes a driver and receiver, allowing two communication paths in one package. The 16-pin wide SOIC footprint supports conventional surface-mount assembly and thermal design without requiring a high-pin-count package. The MAX3232E architecture is intended for systems where a compact true RS-232 interface, low standby consumption, and higher data-rate capability are important. Its 1Mbps maximum rate exceeds the common 250kbps operating point of many older RS-232 transceivers, while the 3.0V minimum supply supports direct operation from modern 3.3V system rails. The ±15kV protection rating improves robustness when exposed cables connect to exposed equipment or industrial control ports. Typical uses include industrial serial controllers, instrumentation, data-acquisition equipment, point-of-sale terminals, and embedded systems that need to connect to an RS-232 host. It is also appropriate for configuration and service ports in communications equipment. When paired with a microcontroller UART, the transceiver can provide bidirectional serial connectivity without implementing the RS-232 voltage levels externally. PCB design should place the charge-pump capacitors and bypass capacitors close to their specified pins. Keep the logic-side and RS-232-side routing paths separated to reduce coupling between fast switching nodes and sensitive receiver inputs. Follow the Analog Devices MAX3232E data sheet for the exact capacitor values, pin assignment, and layout pattern rather than substituting generic RS-232 layouts. This page combines manufacturer specifications, exact-ordering information, compatible alternatives, application guidance, and design notes to support component selection and PCB implementation. It is intended to answer practical engineering questions about voltage compatibility, data rate, ESD protection, pin compatibility, and replacement decisions.

詢價 聯絡我們
MAX3232EEWE+TG1Z - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EEWE+TG1Z

MAX3232EEWE+TG1Z - 1Mbps RS-232 Transceiver | Analog Devices

Analog Devices MAX3232EEWE+TG1Z is a dual transmitter and dual receiver RS-232 interface IC operating from a 3.0V to 5.5V supply. It supports data rates up to 1Mbps, provides ±15kV ESD protection, and is offered in a 16-SOIC package. The device is designed for bidirectional serial data links that require true RS-232 signal levels rather than logic-level UART connections. An RS-232 transceiver is an interface IC within the broader communications-interface and semiconductor hierarchy. Its transmitters convert logic-level UART signals into RS-232 voltage levels, while its receivers convert incoming RS-232 signals back into logic-compatible levels. This allows equipment with different logic voltage domains to communicate across a wired serial interface while adding the electrical characteristics required by RS-232. The MAX3232EEWE+TG1Z provides two transmit channels and two receive channels, a maximum data rate of 1Mbps, and an operating supply range of 3.0V to 5.5V. Its ±15kV ESD protection improves tolerance of electrostatic discharge at connector-facing pins. The low-power design is specified with supply current down to 10nA, making it suitable for systems that need a low-overhead serial interface. The MAX3232 family uses integrated level-shaping circuitry to generate the bipolar voltage levels expected by RS-232 links from a single low-voltage supply. Designers still need to observe the recommended charge-pump capacitor values, connect supply and ground properly, and account for the voltage and current limitations of the RS-232 interface. The manufacturer states that MAX3232E devices are pin, package, and functionally compatible with the industry-standard MAX232, subject to verification of the exact ordering variant. Typical uses include industrial serial consoles, data-acquisition equipment, point-of-sale systems, instrumentation, embedded-control links, and service interfaces. The 16-SOIC package is also convenient for repairs and redesigns of legacy RS-232 equipment because the family maintains compatibility with established MAX232-class interfaces. When designing around this IC, confirm that the host UART uses the correct logic voltage and that the RS-232 cable is connected with the proper signal-to-ground relationship. Place the charge-pump capacitors and bypass capacitance close to their assigned pins, and keep connector protection and chassis-ground strategy separate from the sensitive receiver path. This product page consolidates electrical characteristics, package information, documented drop-in alternatives, and application-focused design guidance. It also distinguishes verified ordering variants from broader MAX3232-family options so engineers can assess PCB reuse, channel count, temperature grade, and lifecycle requirements before approving a substitution.

詢價 聯絡我們
MAX3232EID - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX3232EID

MAX3232EID - 250kbps Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EID is a dual-channel RS-232 line driver and receiver transceiver rated for 250 kbps, operating from a 3 V to 5.5 V supply and providing ±15 kV ESD protection. It is packaged in a 16-pin SOIC package. The device is intended for portable and industrial equipment that converts logic-level UART signals into RS-232 levels and converts received RS-232 signals back to logic levels. An RS-232 transceiver is an interface IC within the broader class of interface semiconductors. It combines a line driver, line receiver, and charge-pump voltage converter in one package. The MAX3232EID provides two driver and two receiver channels, allowing two simultaneous RS-232 links or one bidirectional port when the driver and receiver channels are paired. Its single 3 V to 5.5 V supply simplifies integration with modern 3.3 V and 5 V digital systems. The principal features include two RS-232 drivers, two RS-232 receivers, a maximum signaling rate of 250 kbps, and ESD protection to ±15 kV on the serial-port connection pins. According to the Texas Instruments MAX3232 product page, the MAX3232 family is recommended for new designs. The MAX3232E is an improved direct drop-in replacement for the original MAX3232, while the MAX3232EID suffix identifies the specified device ordering configuration. Internally, the charge-pump circuit develops the positive and negative voltage levels required by the RS-232 signaling standard. Transmit drivers convert CMOS/TTL-compatible input signals to RS-232 levels, while receive channels detect bipolar RS-232 inputs and produce CMOS/TTL-compatible outputs. The architecture makes this device appropriate for equipment with a host UART, an embedded controller, or an industrial data-acquisition system that must communicate with a legacy serial port. Typical uses include barcode scanners, instrumentation, industrial control links, point-of-sale equipment, and service-console connections. The 250 kbps maximum data rate supports conventional serial communication while the ±15 kV ESD rating helps protect exposed connector inputs. In battery-powered or space-constrained equipment, its single-supply operation can simplify voltage planning and reduce the number of external rails. When laying out the circuit, place charge-pump capacitors and the charge-pump flyback capacitor close to their associated device pins, and route RS-232 connector traces away from sensitive analog and high-speed digital paths. Confirm that the selected transceiver supports the baud rate, cable length, logic levels, and connector protection required by the target RS-232 environment. The IC-level ESD rating does not replace correct signal routing and appropriate external protection. This page combines the device specifications, sourcing workflow, family-level alternatives, and application guidance into a practical engineering resource. It also distinguishes verified device characteristics from package-ordering details and highlights the checks needed when evaluating a pin-compatible replacement for an existing MAX3232EID design.

詢價 聯絡我們
MAX3232EIDB - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX3232EIDB

MAX3232EIDB - 250kbps Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIDB is a dual-channel RS-232 line driver and receiver operating from a single 3 V to 5.5 V supply at data-signaling rates up to 250 kbit/s. The device is housed in a 16-pin SSOP package and provides ±15 kV IEC ESD protection on the serial-port connection pins. It interfaces a host UART or asynchronous controller with an RS-232 connector while the integrated dual charge pump supplies the required bipolar line voltage. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 levels and receives RS-232 signals before returning them to the host. In the broader hierarchy, the MAX3232EIDB is an RS-232 transceiver, a line-driver and receiver interface, an interface IC, and ultimately a semiconductor. It is useful where longer cable runs, noise immunity, or compatibility with legacy serial equipment matters more than the low operating voltage and compact size of a modern LVTTL UART. Key features include two transmit channels, two receive channels, a 3 V to 5.5 V single-supply operating range, and operation up to 250 kbit/s. The integrated charge-pump design permits operation from one supply rail, while the four small external charge-pump capacitors support the bipolar voltage required by TIA/EIA-232-F. The MAX3232E also limits driver output slew rate to a maximum of 30 V/µs, helping reduce electromagnetic interference and ringing on connected cables. The device architecture separates the host-facing supply and logic interface from the high-voltage RS-232 line pins. This arrangement allows a low-voltage 3.3 V system to communicate with a conventional RS-232 port without a separate negative supply rail. The charge-pump circuitry generates positive and negative voltages internally, and the receiver converts the bipolar line voltage back to a compatible digital signal. Pin-to-pin and supply arrangement should still be checked against the exact alternative being considered. Typical applications include industrial equipment serial consoles, laboratory instrumentation, point-of-sale terminals, security systems, and service-port connections to legacy computers or controllers. The 250 kbit/s ceiling is suitable for many asynchronous control and diagnostic protocols, although designers should verify that the connected system does not require a faster RS-232 rate. The integrated ESD protection also adds useful robustness at exposed connector pins. For implementation, place the charge-pump capacitors close to their specified pins and route the RS-232 line traces away from sensitive analog and high-speed digital signals. Keep external protection and chassis-ground decisions separate from signal ground to avoid injecting surge current into the transceiver. Confirm the connector's logic polarity and signal direction against the truth tables in the manufacturer datasheet before final PCB routing. This page combines device specifications, drop-in alternatives, package details, application guidance, and design considerations to support faster component selection and implementation. It also identifies which parameters require confirmation from the manufacturer datasheet, helping engineers distinguish documented drop-in options from broader functional equivalents.

詢價 聯絡我們
MAX3232EIDBE4 - 3-5.5V 2/2 RS-232 Transceiver | Texas Instruments
MAX3232EIDBE4

MAX3232EIDBE4 - 3-5.5V 2/2 RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIDBE4 is a 3 V to 5.5 V multichannel RS-232 line driver and receiver with two drivers, two receivers, and ±15 kV IEC ESD protection, housed in a 16-SSOP package. It supports the RS-232 interface for industrial-control, communications, and embedded systems while operating across the extended temperature range of −40°C to +85°C. An RS-232 transceiver is an interface IC that combines differential signal generation and reception for serial communications. It belongs to the line-driver/receiver hierarchy within interface ICs, bridging a host UART or processor logic-level port and a wired RS-232 connection. The MAX3232EIDBE4 is intended for designs that need both transmit and receive functions on one compact, surface-mount device. Key features include a 3 V to 5.5 V supply range, a 2/2 driver-and-receiver configuration, and bus-pin ESD protection rated to ±15 kV using the IEC 61000-4-2 contact-discharge and air-gap-discharge protection referenced in the product description. The 16-SSOP package measures approximately 5.30 mm in width and 0.209 inch in body width. The part is packaged in a tube according to the product listing. The E designation identifies the enhanced MAX3232E family, which Texas Instruments describes as an improved direct drop-in replacement for the original MAX3232. Its integrated charge-pump circuitry supports level translation between low-voltage digital logic and RS-232 signal levels without requiring a separate ±12 V supply. This simplifies interface implementation while retaining the voltage ranges and peripheral arrangement expected in MAX3232-class designs. Typical applications include RS-232 connections between embedded controllers and test equipment, industrial serial consoles, point-of-sale terminals, instrumentation, and legacy peripheral adapters. The two-driver and two-receiver arrangement supports full-duplex point-to-point links, provided the system designer accounts for the directional nature of each channel and applies appropriate interface protection where cables leave an enclosure. When designing a board around the MAX3232EIDBE4, preserve the manufacturer-recommended charge-pump capacitor connections and place the associated ceramic capacitors close to their pins. Confirm that the external connector, cable, and grounding strategy match the intended RS-232 application, because the integrated IC protects its bus pins but cannot compensate for an inadequate enclosure or cable shield. This page combines the device specifications, verified source links, package identification, application guidance, and confirmed same-package alternatives needed to evaluate the MAX3232EIDBE4. It also highlights where a replacement can be used without changing the 16-SSOP land pattern and where temperature, packing, or parameter differences still require engineering review.

詢價 聯絡我們
MAX3232EIDBG4 - Dual RS-232 Transceiver | Texas Instruments
MAX3232EIDBG4

MAX3232EIDBG4 - Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIDBG4 is a dual RS-232 line-driver and line-receiver transceiver with a 3 V to 5.5 V supply, two drivers, two receivers, and ±15 kV IEC ESD protection on the serial-port pins. It is packaged in a 16-pin SSOP and is designed to connect a modern low-voltage controller to an RS-232 serial-port connector. An RS-232 transceiver is an interface IC within the broader semiconductor and interface-controller hierarchy. It converts logic-level signals from an asynchronous communication controller into RS-232 line levels, while receiving and translating remote RS-232 signals back into logic levels. The MAX3232EIDBG4 supports both directions on one compact package, reducing board area compared with separate driver and receiver ICs. The device operates from 3 V to 5.5 V, so it can be powered directly from common 3.3 V or 5 V systems. Its two line drivers and two receivers suit point-to-point serial links, including industrial controllers, POS terminals, data-acquisition equipment, and service interfaces. The integrated dual charge-pump generates the positive and negative voltage levels required by RS-232 without a separate supply. The MAX3232E family is designed to meet TIA/EIA-232-F requirements. According to the manufacturer datasheet, the serial-port pins, including ground, provide ±15 kV IEC ESD protection pin to pin. This protection is valuable when cables connect the board to external equipment through uncontrolled connector environments. The improved MAX3232E is also described by Texas Instruments as a direct drop-in replacement for the original MAX3232. Typical uses include RS-232 adapters for embedded processors, configuration links on industrial automation equipment, instrument-control ports, and legacy peripheral connections. The 3 V to 5.5 V operating range makes the interface suitable for both 5 V industrial systems and modern 3.3 V controller platforms. Place the charge-pump capacitors and the interface bypass capacitor close to their designated pins, and route the exposed connector-side signals away from sensitive clock and analog traces. Confirm polarity and signal direction at the RS-232 connector because the logic-side and line-side pin functions are not interchangeable. This page organizes the electrical limits, package information, replacement options, comparison parameters, and practical layout guidance needed to evaluate the MAX3232EIDBG4 before integrating it into an RS-232 interface design.

詢價 聯絡我們
MAX3232EIDBR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3232EIDBR

MAX3232EIDBR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3232EIDBR is a dual-channel RS-232 line driver and receiver operating from a single 3 V to 5.5 V supply at data-signaling rates up to 250 kbit/s. The device is housed in a 16-pin SSOP package and provides ±15 kV IEC ESD protection on the serial-port connection pins. It interfaces a host UART or asynchronous controller with an RS-232 connector while the integrated dual charge pump supplies the required bipolar line voltage. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 levels and receives RS-232 signals before returning them to the host. In the broader hierarchy, the MAX3232EIDBR is an RS-232 transceiver, a line-driver and receiver interface, an interface IC, and ultimately a semiconductor. It is useful where longer cable runs, noise immunity, or compatibility with legacy serial equipment matters more than the low operating voltage and compact size of a modern LVTTL UART. Key features include two transmit channels, two receive channels, a 3 V to 5.5 V single-supply operating range, and operation up to 250 kbit/s. The integrated charge-pump design permits operation from one supply rail, while the four small external charge-pump capacitors support the bipolar voltage required by TIA/EIA-232-F. The MAX3232E also limits driver output slew rate to a maximum of 30 V/µs, helping reduce electromagnetic interference and ringing on connected cables. The device architecture separates the host-facing supply and logic interface from the high-voltage RS-232 line pins. This arrangement allows a low-voltage 3.3 V system to communicate with a conventional RS-232 port without a separate negative supply rail. The charge-pump circuitry generates positive and negative voltages internally, and the receiver converts the bipolar line voltage back to a compatible digital signal. Pin-to-pin and supply arrangement should still be checked against the exact alternative being considered. Typical applications include industrial equipment serial consoles, laboratory instrumentation, point-of-sale terminals, security systems, and service-port connections to legacy computers or controllers. The 250 kbit/s ceiling is suitable for many asynchronous control and diagnostic protocols, although designers should verify that the connected system does not require a faster RS-232 rate. The integrated ESD protection also adds useful robustness at exposed connector pins. For implementation, place the charge-pump capacitors close to their specified pins and route the RS-232 line traces away from sensitive analog and high-speed digital signals. Keep external protection and chassis-ground decisions separate from signal ground to avoid injecting surge current into the transceiver. Confirm the connector's logic polarity and signal direction against the truth tables in the manufacturer datasheet before final PCB routing. This page combines device specifications, drop-in alternatives, package details, application guidance, and design considerations to support faster component selection and implementation. It also identifies which parameters require confirmation from the manufacturer datasheet, helping engineers distinguish documented drop-in options from broader functional equivalents.

詢價 聯絡我們
MAX3232EIDR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3232EIDR

MAX3232EIDR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3232EIDR is a dual-channel RS-232 line driver and receiver transceiver rated for 250 kbps, operating from a 3 V to 5.5 V supply and providing ±15 kV ESD protection. It is packaged in a 16-pin SOIC package. The device is intended for portable and industrial equipment that converts logic-level UART signals into RS-232 levels and converts received RS-232 signals back to logic levels. An RS-232 transceiver is an interface IC within the broader class of interface semiconductors. It combines a line driver, line receiver, and charge-pump voltage converter in one package. The MAX3232EIDR provides two driver and two receiver channels, allowing two simultaneous RS-232 links or one bidirectional port when the driver and receiver channels are paired. Its single 3 V to 5.5 V supply simplifies integration with modern 3.3 V and 5 V digital systems. The principal features include two RS-232 drivers, two RS-232 receivers, a maximum signaling rate of 250 kbps, and ESD protection to ±15 kV on the serial-port connection pins. According to the Texas Instruments MAX3232 product page, the MAX3232 family is recommended for new designs. The MAX3232E is an improved direct drop-in replacement for the original MAX3232, while the MAX3232EIDR suffix identifies the specified device ordering configuration. Internally, the charge-pump circuit develops the positive and negative voltage levels required by the RS-232 signaling standard. Transmit drivers convert CMOS/TTL-compatible input signals to RS-232 levels, while receive channels detect bipolar RS-232 inputs and produce CMOS/TTL-compatible outputs. The architecture makes this device appropriate for equipment with a host UART, an embedded controller, or an industrial data-acquisition system that must communicate with a legacy serial port. Typical uses include barcode scanners, instrumentation, industrial control links, point-of-sale equipment, and service-console connections. The 250 kbps maximum data rate supports conventional serial communication while the ±15 kV ESD rating helps protect exposed connector inputs. In battery-powered or space-constrained equipment, its single-supply operation can simplify voltage planning and reduce the number of external rails. When laying out the circuit, place charge-pump capacitors and the charge-pump flyback capacitor close to their associated device pins, and route RS-232 connector traces away from sensitive analog and high-speed digital paths. Confirm that the selected transceiver supports the baud rate, cable length, logic levels, and connector protection required by the target RS-232 environment. The IC-level ESD rating does not replace correct signal routing and appropriate external protection. This page combines the device specifications, sourcing workflow, family-level alternatives, and application guidance into a practical engineering resource. It also distinguishes verified device characteristics from package-ordering details and highlights the checks needed when evaluating a pin-compatible replacement for an existing MAX3232EIDR design.

詢價 聯絡我們
MAX3232EIDWG4 - Dual RS-232 IC | Texas Instruments
MAX3232EIDWG4

MAX3232EIDWG4 - Dual RS-232 IC | Texas Instruments

The Texas Instruments MAX3232EIDWG4 is a dual-channel RS-232 line driver and receiver interface IC with a 3 V to 5.5 V supply range, ±15 kV IEC ESD protection, and a 16-pin SOIC package. It converts CMOS/TTL logic levels to RS-232 levels and converts incoming RS-232 signals back to logic levels. An RS-232 interface transceiver is a semiconductor that bridges the voltage-domain difference between digital logic and the bipolar RS-232 serial interface. The MAX3232EIDWG4 belongs to the interface IC hierarchy, where a transceiver integrates one or more line drivers and receivers with charge-pump circuitry and electrostatic-discharge protection. It is commonly placed between a microcontroller UART and an external serial connector. Key features include two driver and two receiver channels, operation from 3 V to 5.5 V, and ±15 kV IEC ESD protection. The E suffix identifies the enhanced ESD-capable family, while the G4 ordering code denotes the green, standard industrial-temperature version associated with a −40 °C to +85 °C operating range. The 16-pin SOIC package supports conventional surface-mount assembly and is compatible with automated PCB production. The MAX3232E uses on-chip charge-pump circuitry to generate the positive and negative voltage swings required by RS-232 without a negative supply input. This architecture allows the logic side to operate from a single 3 V to 5.5 V rail. The interface includes integrated protection for external connector signals, reducing the need for separate low-capacitance TVS devices when the board layout and routing follow the manufacturer's recommendations. Typical applications include industrial serial controllers, test and measurement equipment, computer peripherals, point-of-sale terminals, embedded service ports, and legacy RS-232 equipment connected to modern microcontrollers. The dual-channel arrangement is useful when one system must support bidirectional communication, multiple RS-232 devices, or separate transmit and receive data paths. PCB design should place the device near the RS-232 connector, route driver outputs and receiver inputs away from sensitive logic, and connect the charge-pump capacitors and supply-decoupling capacitor close to their specified pins. Keep unprotected external leads short and follow the datasheet's ESD layout guidance so that system-level transient performance is not limited by long copper traces. This product page combines the exact ordering information, electrical limits, interface characteristics, package details, drop-in alternatives, comparison parameters, and practical PCB guidance needed to evaluate and implement the MAX3232EIDWG4 in a new design.

詢價 聯絡我們
MAX3232EIPW - 250kbps RS-232 Transceiver | Texas Instruments
MAX3232EIPW

MAX3232EIPW - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIPW is a dual-channel RS-232 line driver and receiver operating from a single 3 V to 5.5 V supply at data rates up to 250 kbps, housed in a 16-pin TSSOP package. It provides two transmit channels, two receive channels, an integrated dual charge pump, and ±15 kV IEC ESD protection on the serial-port pins. An RS-232 transceiver is an interface IC that converts logic-level signals from a controller or microcontroller into RS-232 voltage levels, while converting received RS-232 signals back into logic-compatible outputs. Within the broader hierarchy, the MAX3232EIPW is an RS-232 transceiver, serial-interface IC, interface IC, and semiconductor designed for asynchronous serial communications. The MAX3232E family operates without a separate 5 V-only supply, making it suitable for mixed-voltage systems with 3.3 V or 5 V logic. Its charge-pump circuitry develops the positive and negative voltages required by RS-232 from the single supply. The device supports 250 kbps operation and includes TIA/EIA-232-F-compatible electrical behavior according to the Texas Instruments product page. The integrated protection is a major functional distinction from older MAX3232 devices. The manufacturer identifies ±15 kV IEC ESD protection from pin to pin on the serial-port connections, including ground, while the MAX3232E remains a direct drop-in replacement for the original MAX3232. This makes it appropriate for exposed equipment, industrial interfaces, and systems where a disconnected cable may introduce electrostatic discharge. Typical uses include RS-232 ports on industrial controllers, test equipment, POS terminals, data acquisition units, service interfaces, and legacy peripherals that require a full-duplex serial connection. The device can also serve as the physical-layer interface between a 3.3 V microcontroller UART and an RS-232 connector. PCB design should place the charge-pump capacitors close to their associated pins and route the RS-232 connector nets away from sensitive analog or high-speed digital traces. The TSSOP-16 footprint permits a compact layout, but connector protection, grounding, and cable-retention requirements can dominate the available board area. Confirm signal polarity, flow-control assumptions, and the connector pin assignment before replacing an existing design. This product record combines the manufacturer's device capabilities, package information, interface requirements, drop-in alternatives, and practical PCB guidance. It also distinguishes the electrically enhanced MAX3232E from older non-E variants so engineers can make a compatibility decision based on protection and operating requirements rather than package similarity alone.

詢價 聯絡我們
MAX3232EIPWE4 - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX3232EIPWE4

MAX3232EIPWE4 - 250kbps Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIPWE4 is a dual RS-232 line driver and receiver IC providing two transmit channels and two receive channels, a maximum signaling rate of 250 kbps, and operation from a 3 V to 5.5 V supply in a 16-pin TSSOP package. The device provides ±15 kV IEC ESD protection on its interface pins. An RS-232 transceiver is an interface integrated circuit that converts between single-ended logic-level signals and differential, bipolar RS-232 signals. It belongs to the line-driver and receiver family, then to the broader transceiver and interface IC hierarchy. The MAX3232EIPWE4 implements the physical-layer signaling required by TIA/EIA-232-F and ITU V.28 systems while presenting ordinary CMOS logic levels to the host controller. Key features include a 2/2 driver-receiver configuration, 3 V to 5.5 V operation, 250 kbps data rate, and ±15 kV IEC ESD protection. The -40 °C to 85 °C industrial temperature range supports both commercial and industrial equipment. Tape-and-reel packaging is identified for the E suffix, while the 16-TSSOP body measures 0.173 inches, or 4.40 mm, in width. The MAX3232 family uses charge-pump circuitry to generate the positive and negative voltage levels required by RS-232 transmitters. This allows the device to communicate over cable distances where the receiver must tolerate bipolar signal swings relative to ground. The integrated protection circuits help improve system robustness when users connect external cables or connectors to the board. Typical uses include industrial serial consoles, data-acquisition equipment, instrumentation, printer interfaces, and embedded systems that exchange data with legacy RS-232 peripherals. The 250 kbps maximum rate is suitable for command-and-control links rather than high-throughput storage transfers. The 3 V supply option also helps reduce the logic power requirement in mixed-voltage embedded designs. When laying out this device, place the charge-pump capacitors close to their designated pins, route transceiver outputs toward the connector, and keep sensitive logic-side traces away from cable-side nets. Confirm line-driver load capability, receiver thresholds, and system grounding in the manufacturer datasheet before releasing a high-volume design.

詢價 聯絡我們
MAX3232EIPWR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
MAX3232EIPWR

MAX3232EIPWR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)

The Texas Instruments MAX3232EIPWR is a dual-channel RS-232 line driver and receiver operating from a single 3 V to 5.5 V supply at data rates up to 250 kbps, housed in a 16-pin TSSOP package. It provides two transmit channels, two receive channels, an integrated dual charge pump, and ±15 kV IEC ESD protection on the serial-port pins. An RS-232 transceiver is an interface IC that converts logic-level signals from a controller or microcontroller into RS-232 voltage levels, while converting received RS-232 signals back into logic-compatible outputs. Within the broader hierarchy, the MAX3232EIPWR is an RS-232 transceiver, serial-interface IC, interface IC, and semiconductor designed for asynchronous serial communications. The MAX3232E family operates without a separate 5 V-only supply, making it suitable for mixed-voltage systems with 3.3 V or 5 V logic. Its charge-pump circuitry develops the positive and negative voltages required by RS-232 from the single supply. The device supports 250 kbps operation and includes TIA/EIA-232-F-compatible electrical behavior according to the Texas Instruments product page. The integrated protection is a major functional distinction from older MAX3232 devices. The manufacturer identifies ±15 kV IEC ESD protection from pin to pin on the serial-port connections, including ground, while the MAX3232E remains a direct drop-in replacement for the original MAX3232. This makes it appropriate for exposed equipment, industrial interfaces, and systems where a disconnected cable may introduce electrostatic discharge. Typical uses include RS-232 ports on industrial controllers, test equipment, POS terminals, data acquisition units, service interfaces, and legacy peripherals that require a full-duplex serial connection. The device can also serve as the physical-layer interface between a 3.3 V microcontroller UART and an RS-232 connector. PCB design should place the charge-pump capacitors close to their associated pins and route the RS-232 connector nets away from sensitive analog or high-speed digital traces. The TSSOP-16 footprint permits a compact layout, but connector protection, grounding, and cable-retention requirements can dominate the available board area. Confirm signal polarity, flow-control assumptions, and the connector pin assignment before replacing an existing design. This product record combines the manufacturer's device capabilities, package information, interface requirements, drop-in alternatives, and practical PCB guidance. It also distinguishes the electrically enhanced MAX3232E from older non-E variants so engineers can make a compatibility decision based on protection and operating requirements rather than package similarity alone.

詢價 聯絡我們
MAX3232EIPWRG4 - Dual 250kbps RS-232 IC | Texas Instruments
MAX3232EIPWRG4

MAX3232EIPWRG4 - Dual 250kbps RS-232 IC | Texas Instruments

The Texas Instruments MAX3232EIPWRG4 is a dual-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply at data rates up to 250 kbps. The device includes two drivers, two receivers, a dual charge-pump circuit, and pin-to-pin ±15 kV IEC ESD protection in a 16-pin TSSOP package. It is designed to bridge a 3.3 V or 5 V asynchronous communication controller and a conventional RS-232 serial port. An RS-232 transceiver is an interface integrated circuit that converts logic-level UART signals into RS-232 line levels and converts received RS-232 levels back into CMOS-compatible logic. The MAX3232E belongs to the interface IC hierarchy, where an RS-232 transceiver combines line drivers, line receivers, voltage generation, and electrostatic-discharge protection. Its dual charge-pump design provides the positive and negative voltage levels required for single-ended RS-232 signaling without a separate negative power supply. Key characteristics include a 3 V to 5.5 V operating supply, two driver and two receiver channels, operation to 250 kbps, and ±15 kV IEC ESD protection on the serial-port pins. The MAX3232E meets the requirements of TIA/EIA-232-F and ITU V.28. These features support compatibility with conventional PC serial ports, industrial equipment, data-acquisition systems, and embedded UART links that require protection at the connector-facing interface. The internal charge pumps require external flying capacitors, while the driver and receiver sections use small bypass capacitors for stable operation. The MAX3232E is particularly useful when the host-side UART operates from a low-voltage rail but the external cable uses RS-232 voltage levels. Its dual-channel arrangement allows one device to carry two independently directed RS-232 signals when one line is assigned to transmit and the other to receive. Typical applications include industrial controller-to-console connections, test and measurement equipment, POS terminals, instrumentation links, and data-logger interfaces. The MAX3232EIPWRG4 is also appropriate for designs that need a compact 16-pin TSSOP implementation rather than a larger multi-channel RS-232 family. When laying out the PCB, keep charge-pump capacitors close to their designated pins and place the interface-side protection network near the RS-232 connector. Confirm connector-level voltage levels, ground continuity, cable routing, and device operating temperature before releasing the design. The manufacturer product page identifies the PW package as a 16-pin option rated from -40°C to 85°C. This page combines manufacturer specifications, package and application guidance, drop-in replacement analysis, and engineering-focused design notes to support faster component selection and PCB implementation.

詢價 聯絡我們
MAX3232EIPWRQ1 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3232EIPWRQ1

MAX3232EIPWRQ1 - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIPWRQ1 is an automotive-qualified, 2/2 RS-232 line-driver and receiver transceiver operating from a 3 V to 5.5 V supply at up to 250 kbit/s in a 16-pin TSSOP package. It provides pin-to-pin ±15 kV IEC ESD protection on the serial-port connection pins and incorporates a dual charge-pump circuit for RS-232 signal-level conversion. An RS-232 transceiver is the interface between a modern low-voltage digital controller and a physical serial port. It belongs to the interface-IC hierarchy, where transceivers combine digital line drivers, line receivers, voltage conversion, and electrostatic-discharge protection. The MAX3232E-Q1 family is designed for industrial and automotive systems requiring TIA/EIA-232-F and ITU V.28-compatible operation. The device includes two line drivers and two line receivers. Its 3 V to 5.5 V VCC operating range supports both 3.3 V and 5 V system rails, while its maximum data rate of 250 kbit/s covers legacy serial-port, industrial-control, and point-to-point communications. The typical standby current is 300 µA, and the dual charge pump supplies the positive and negative voltage levels required to generate compliant RS-232 output levels. The MAX3232EIPWRQ1 also meets or exceeds TIA/EIA-232-F and ITU V.28 requirements. Pin-to-pin ±15 kV IEC ESD protection strengthens the interface against electrostatic discharge on exposed serial connections. Because the IC combines level translation, charge-pump generation, and protection, the design can use fewer external components than a discrete RS-232 implementation. Typical applications include automotive diagnostic and service interfaces, industrial serial controllers, programmable-logic-controller communications, point-to-point RS-232 links, and embedded systems that retain a legacy serial console. The 16-pin TSSOP package supports compact control boards, while the automotive qualification makes the device suitable for electrically harsh vehicle environments when the complete system requirements are satisfied. Design the charge-pump capacitors and VCC bypass capacitor close to their associated pins, and keep the serial traces away from high-current switching paths. Confirm that cable length, baud rate, grounding, and connector selection remain suitable for the chosen RS-232 application. The maximum data rate is 250 kbit/s, so it should not be selected for faster differential links or unrelated high-speed serial protocols. This page consolidates the exact electrical ratings, package information, interface standards, application guidance, and verified drop-in alternatives of the MAX3232EIPWRQ1 into an engineering-focused selection reference.

詢價 聯絡我們
MAX3232EIPWRSV - 250kbps Dual RS-232 Transceiver | Texas Instruments
MAX3232EIPWRSV

MAX3232EIPWRSV - 250kbps Dual RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3232EIPWRSV is a dual-channel RS-232 line driver and receiver operating from a 3 V to 5.5 V supply at up to 250 kbps. It integrates two line drivers, two line receivers, and a dual charge-pump circuit with plus or minus 15 kV IEC ESD protection on the serial-port terminals. The device is packaged in a 16-pin SSOP package. A transceiver, also called a line driver/receiver, converts logic-level UART signals into RS-232 bipolar voltage levels and converts received RS-232 levels back into CMOS-compatible logic. The MAX3232E belongs to the RS-232 interface IC hierarchy, where it sits between a UART controller and a DB9, terminal, or other serial connector. Its charge-pump circuit generates the positive and negative voltages required by the TIA/EIA-232-F interface without a separate negative power supply. The MAX3232E family provides plus or minus 15 kV IEC ESD protection, automatic driver slew control, and operation from both 3 V and 5 V systems. A single device supports two serial channels through two drivers and two receivers. The dual architecture is useful for console management, configuration ports, instrument control, and industrial equipment that exchanges data with legacy RS-232 equipment. Its internal design uses a dual charge-pump circuit to produce the RS-232 voltage swings while maintaining a low-voltage CMOS supply. The driver outputs include slew-rate control to limit electromagnetic interference and help control ringing on the cable. The receiver side provides signal conditioning for reliable interpretation of the bipolar RS-232 signal, while the integrated ESD structures protect the external terminals. Typical uses include industrial controllers, laboratory instruments, POS terminals, security equipment, and service interfaces. Since many modern computers no longer include an RS-232 port, the MAX3232E remains valuable for connecting embedded controllers and legacy peripherals. It can also translate between a 3.3 V UART and a 5 V-powered RS-232 link where appropriate logic levels and cable requirements are observed. When laying out the circuit, place the charge-pump capacitors and the required ceramic bypass capacitor close to their associated pins. Route each RS-232 driver output directly to its connector and keep the protected connector-side traces short and away from sensitive analog or high-speed digital nets. Confirm the connector pinout, cable length, ground reference, and signal polarity before populating the board. This page combines manufacturer specifications, ordering data, drop-in replacement options, and practical interface-design guidance in one place. It also organizes the differences among MAX3232, MAX3232E, TRS3232E, MAX3243E, and TRS3243E so engineers can shortlist a compatible transceiver without overlooking supply or logic-level details.

詢價 聯絡我們
MAX3232ESE+ - Dual RS-232 Transceiver | Maxim Integrated
MAX3232ESE+

MAX3232ESE+ - Dual RS-232 Transceiver | Maxim Integrated

The Analog Devices MAX3232ESE+ is a dual RS-232 transceiver with two transmitters and two receivers, a 3.0 V to 5.5 V supply range, and operation up to 1 Mbps in a 16-pin SOIC package. It is designed for bidirectional serial-interface conversion between modern CMOS/TTL logic and RS-232 voltage levels. An RS-232 transceiver is an interface IC that converts low-voltage digital signaling into differential, bipolar RS-232-compatible levels and converts received RS-232 signals back into logic-compatible levels. The MAX3232 belongs to the broader transceiver and interface-IC hierarchy, bridging host controllers, industrial equipment, data-acquisition systems, and service ports. Key verified attributes include two driver channels, two receiver channels, full RS-232 operation, a 3.0 V to 5.5 V supply range, and data rates up to 1 Mbps. The low-power design is suitable for systems where an RS-232 connection must be retained without using a full-sized legacy driver. The 16-pin SOIC footprint supports conventional surface-mount assembly. The device is intended for applications requiring RS-232 electrical compatibility rather than differential RS-485 signaling. Its integrated transmitter and receiver sections make it useful for console connections, configuration ports, embedded control links, and equipment communication. The exact charge-pump capacitor values, receiver thresholds, propagation delays, and electrical limits are not provided in the verified web data and must be checked in the manufacturer datasheet before production design. Typical uses include low-voltage MCU serial consoles, industrial configuration interfaces, test equipment, and legacy peripheral connections. Because RS-232 is point-to-point and single-ended, cable routing, grounding, and protection practices remain important. Use ESD protection and appropriate cable-level transient protection when the connector is exposed to user or industrial environments. Designers should verify the exact MAX3232ESE+ pinout, supply decoupling requirements, capacitor selection, and logic-level compatibility from the manufacturer datasheet. This page combines distributor listings, cross-reference information, and engineering guidance; it does not substitute for the complete manufacturer datasheet for production release.

詢價 聯絡我們
MAX3232ESE+T - 3.0-5.5V RS-232 Transceiver, 1Mbps, 16-SOIC | Maxim
MAX3232ESE+T

MAX3232ESE+T - 3.0-5.5V RS-232 Transceiver, 1Mbps, 16-SOIC | Maxim

The Maxim Integrated MAX3232ESE+T (now under Analog Devices / Maxim Integrated) is a 3.0 V to 5.5 V, true RS-232 transceiver with two drivers and two receivers, supporting data rates up to 1 Mbps in a 16-pin SOIC (NSOIC, 0.150 inch) package. It operates from a single 3.0 V to 5.5 V supply and integrates a high-efficiency charge pump with four external 0.1 µF capacitors to generate ±5.5 V RS-232 levels from the input rail. The device is offered on tape-and-reel (the +T is the reel indicator). An RS-232 transceiver is a line driver/receiver IC that translates logic-level (TTL/CMOS) signals from a microcontroller or UART to the +/-5 V to +/-15 V signaling required by the EIA/TIA-232 standard, and vice versa. RS-232 transceivers sit between the data terminal equipment (DTE) and data communication equipment (DCE) and form part of the physical layer of the UART/serial interface family, alongside RS-422 and RS-485 transceivers for longer-distance differential links. Key features of the MAX3232ESE+T include 1 Mbps guaranteed data rate (250 KB/s in the older 160 ns slew-rate version), low supply current of 1 mA typical, an enhanced ESD protection of +/-15 kV HBM on the RS-232 bus pins, and true RS-232 output swing with automatic power-down shutdown. It also provides a low-dropout transmitter output stage so true RS-232 levels are maintained even when VCC drops to 3.0 V. The architecture uses a regulated dual charge pump and four small 0.1 µF ceramic capacitors, eliminating the bulky +/-12 V rails and 1 µF / 10 µF pump capacitors required by classic MAX232 designs. This shrinks the BOM and PCB area and enables portable 3.3 V-only systems to drive full-spec RS-232 links without auxiliary supplies. The part is pin-compatible with the industry-standard MAX232 family. Typical applications include battery-powered serial ports on portable equipment, embedded UART-to-RS-232 bridges on 3.3 V microcontroller boards (e.g. PIC32 and STM32 designs), industrial control and point-of-sale terminals, GPS receiver interfaces, and legacy PC COM-port replacements. Designers of lithium-ion-powered products appreciate the 1 mA supply current. When designing with this part, place the four 0.1 µF charge-pump capacitors (C1-C4) as close as possible to the package and keep the RS-232 trace lengths short. Decouple VCC with 0.1 µF in parallel with 1 µF, and add a series ferrite or TVS if the link will see ESD events beyond the +/-15 kV HBM rating. Note that MAX3232ESE (slew-rate-limited, 160 ns version) is the 250 KBps part; the MAX3232E and 'E' suffix are typically the 1 Mbps variants - verify the exact suffix on the order code before committing to a 1 Mbps design. This page synthesizes distributor pricing, drop-in cross-brand alternatives (TI TRSF3232, Exar SP3232, TI TRS2023), application context not found in the datasheet alone, and an engineering-grade pinout to support sourcing, design-in, and drop-in substitution decisions.

詢價 聯絡我們
MAX3232ESE+TG035 - 2x2 RS-232 Transceiver, 3-5.5V | Maxim
MAX3232ESE+TG035

MAX3232ESE+TG035 - 2x2 RS-232 Transceiver, 3-5.5V | Maxim

The Analog Devices Inc./Maxim Integrated MAX3232ESE+TG035 is a low-power, true RS-232 transceiver with 2 drivers and 2 receivers, operating from a 3.0V to 5.5V supply at data rates up to 1Mbps, housed in a 16-pin SOIC (N) package using only four external 0.1uF capacitors. An RS-232 transceiver is an interface IC that converts TTL/CMOS logic levels (typically 0-5V or 0-3.3V) into the RS-232 voltage convention (nominally +/-5V to +/-15V) and back, allowing microcontrollers to communicate with legacy serial ports, modems, and industrial equipment. Within the signal-chain hierarchy it belongs to interface ICs -> drivers/receivers/transceivers -> line transceivers, sitting between the UART logic pin of a processor and the physical DB-9 serial connector. Key features include the wide 3.0V to 5.5V single-supply range that supports both 3.3V and 5V systems, guaranteed 250kbps operation with 3V/1uF load and up to 1Mbps minimum data rate under standard conditions, and the proprietary charge-pump architecture requiring only four 0.1uF external capacitors instead of the large 5uF capacitors of older generation devices. Technically, the device integrates dual charge pumps with cascaded voltage doublers and inverters to generate +5.5V and -5.5V rails internally from the logic supply. The E-suffix grade is specified for -40C to +85C operation. The drivers meet or exceed EIA/TIA-232 and V.28 requirements, and the receivers feature a 0.5V input threshold with 5V-tolerant operation and schmitt-trigger hysteresis for noise immunity. Typical applications include industrial fieldbus adapters, point-of-sale terminals, battery-powered instrumentation with DB-9 debug ports, and legacy PC serial maintenance interfaces. The TG035 suffix identifies the tape-and-reel packaging variant for automated pick-and-place assembly. Design consideration: use 0.1uF charge-pump capacitors rated at 16V or higher and place them close to the IC pins; larger capacitors (1uF) are only needed when running near the 1Mbps rate at 3.3V. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
MAX3232EUE+ - 3.0-5.5V 1Mbps RS-232 Transceiver | Maxim
MAX3232EUE+

MAX3232EUE+ - 3.0-5.5V 1Mbps RS-232 Transceiver | Maxim

The Maxim Integrated MAX3232EUE+ is a 3.0 V to 5.5 V, low-power, true RS-232 transceiver with two transmitters, two receivers, and operation up to 1 Mbps in a 16-pin TSSOP package. Its dual charge-pump design generates the bipolar voltage levels required by RS-232 while allowing the device to operate from a single 3.0 V to 5.5 V supply. An RS-232 transceiver is an interface IC that converts between logic-level signals used by digital systems and bipolar voltage signals used by RS-232 links. It belongs to the interface IC category and connects host controllers, test equipment, industrial systems, and peripheral controllers through the EIA RS-232 standard. A dual transceiver supports two communication channels on one device while reducing board area and component count. The MAX3232EUE+ operates from 3.0 V to 5.5 V and supports data rates up to 1 Mbps. Its true RS-232 transmitter output stage uses low-dropout operation, while the internal dual charge pump requires only four external 0.1 uF capacitors. The 16-TSSOP package is suitable for compact surface-mount equipment, although its narrow lead pitch requires careful PCB assembly and soldering. The transceiver architecture separates the transmit and receive paths, allowing one side of the interface to remain active while the other handles incoming data. This makes the device suitable for systems with asynchronous serial links, local control ports, and communication with legacy RS-232 equipment. The single-supply implementation also simplifies power design in systems that do not provide a separate negative voltage rail. Typical applications include industrial controller serial ports, laboratory data acquisition, point-of-sale equipment, security systems, embedded instrument interfaces, and general-purpose RS-232 links. Systems requiring two serial channels can use the two transmitters and two receivers in one package. The 1 Mbps capability accommodates substantially faster links than the commonly used 115.2 kbaud RS-232 rate. When placing the device, position the four 0.1 uF charge-pump capacitors close to their associated pins and preserve the pinout shown in the manufacturer datasheet. Confirm cable-length limitations because higher baud rates reduce the practical distance supported by RS-232. The interface also needs appropriate protection and grounding when connected to exposed or industrial cabling. This page combines electrical specifications, package guidance, application fit, comparison data, and drop-in replacement information to support faster component selection and PCB implementation. It also identifies the key technical distinctions engineers should verify when considering another RS-232 transceiver.

詢價 聯絡我們
MAX3232EUE+T - Dual RS-232 Transceiver | Analog Devices
MAX3232EUE+T

MAX3232EUE+T - Dual RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EUE+T is a dual RS-232 transceiver with two drivers, two receivers, and a dual charge-pump circuit, operating from 3.0 V to 5.5 V at data rates up to 1 Mbps in a 16-pin TSSOP package. It is designed for bidirectional asynchronous serial communication between modern digital systems and legacy RS-232 equipment. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compliant voltage levels and restores RS-232 inputs to compatible logic levels. The MAX3232 belongs to the interface IC hierarchy, combining line drivers, line receivers, charge pumps, and protection functions in one device. Its charge-pump architecture supports true RS-232 operation from a single 3.0 V to 5.5 V supply without a separate negative supply rail. The device requires only four external 0.1 µF charge-pump capacitors. Its integrated dual charge pump generates the positive and negative voltages needed by the drivers, while the receiver side converts incoming serial data into CMOS-compatible signals. The MAX3232E family provides low power consumption, including approximately 300 µA typical quiescent current reported for the MAX3232EUE+T, making it suitable for equipment where both interface performance and operating efficiency matter. With two transmit and two receive channels, the transceiver can support two RS-232 ports or provide hardware flow-control signals alongside one primary data channel. Operation from 3.0 V to 5.5 V allows use with 3.3 V and 5 V logic systems. Its 16-pin TSSOP package supports compact surface-mount assemblies, while the stated data-rate capability of up to 1 Mbps suits higher-speed serial links, instrumentation, and industrial control equipment. Typical applications include industrial serial consoles, point-of-sale terminals, test and measurement equipment, barcode scanners, and embedded systems communicating with legacy RS-232 peripherals. The device is especially useful when the logic supply is 3.3 V but the attached peripheral still requires true bipolar RS-232 signaling. For a reliable layout, place all four 0.1 µF charge-pump capacitors close to their associated pins and route the RS-232 connector interface away from sensitive analog and high-speed digital traces. Confirm signal polarity, flow-control direction, and connector pin assignments during schematic review because the transmit and receive pins are dedicated rather than automatically interchangeable. This page combines the manufacturer's electrical and package information with same-family drop-in alternatives, application guidance, interface-design notes, and a parameter comparison. It is intended to help engineers identify the correct MPN, validate PCB compatibility, and implement a reliable RS-232 interface.

詢價 聯絡我們
MAX3232EWE+T - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EWE+T

MAX3232EWE+T - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EWE+T is a 3.0 V to 5.5 V, low-power, true RS-232 transceiver with two drivers and two receivers, supporting data rates up to 1 Mbps in a 16-SOIC package. It provides plus or minus 15 kV ESD protection on the serial-port connection pins and operates from four 0.1 uF charge-pump capacitors. A true RS-232 transceiver converts logic-level signals from a UART, microcontroller, or host into balanced, bipolar serial-port levels, then converts incoming serial signals back into CMOS-compatible logic. Within the interface hierarchy, the MAX3232E is a full-duplex RS-232 transceiver, a line-driver and line-receiver circuit, and a serial interface IC commonly used for legacy serial ports, industrial equipment, and embedded control links. Key features include a 3.0 V minimum supply voltage, a 5.5 V maximum supply voltage, and an operating data rate of up to 1 Mbps. The MAX3232E adds plus or minus 15 kV ESD protection, while its low-power design supports shutdown and reduced-power operating modes for portable or space-constrained equipment. Four external 0.1 uF capacitors allow the on-chip charge pump to generate the positive and negative voltages required by true RS-232 drivers. Internally, the device combines two line drivers, two line receivers, and a dual charge-pump circuit. The charge-pump architecture supports operation from a single 3.0 V to 5.5 V supply instead of a plus or minus voltage source. This simplifies board design, although external capacitor placement and connector-side transient protection remain essential for reliable serial links in industrial environments. Typical applications include RS-232 connections to test and measurement equipment, database controllers, modems, point-of-sale terminals, industrial control panels, and legacy service-port interfaces. The 1 Mbps capability is useful for short, point-to-point links where legacy software expects standard RS-232 signaling, while the 16-SOIC package simplifies assembly on through-hole-compatible boards. When laying out this transceiver, place the four 0.1 uF charge-pump capacitors close to their designated pins and route connector-side signals away from sensitive logic. Keep the interface ground reference close to the connector ground and confirm that the host UART voltage levels match the MAX3232E logic supply. This page organizes the MAX3232EWE+T specifications, package details, drop-in alternatives, application guidance, and design notes into a single engineering reference for RS-232 interface design and sourcing decisions.

詢價 聯絡我們
MAX3232EWE-TG068 - 1Mbps RS-232 Transceiver | Analog Devices
MAX3232EWE-TG068

MAX3232EWE-TG068 - 1Mbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3232EWE-TG068 is a true RS-232 transceiver with two drivers and two receivers, operation from 3.0 V to 5.5 V, and data rates up to 1 Mbps in a 16-pin SOIC package. The MAX3232E family is designed for low-power industrial and embedded serial interfaces using 0.1 µF charge-pump capacitors. A true RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into logic levels. It belongs to the RS-232 transceiver class, interface IC category, and broader data-conversion and communications-semiconductor hierarchy. Such devices bridge UART, microcontroller, industrial-controller, and data-acquisition equipment across the voltage, noise, and ground-offset differences inherent in RS-232 links. The principal features of the MAX3232E include a 3.0 V to 5.5 V supply range, operation up to 1 Mbps, and integrated charge-pump circuitry that permits the use of four 0.1 µF capacitors. The 2/2 channel arrangement supports two RS-232 transmit channels and two receive channels in one package. Its 16-pin SOIC format supports conventional surface-mount assembly while conserving board area in compact control and communications equipment. The MAX3232E architecture is appropriate for systems in which a logic-level UART must communicate with legacy RS-232 peripherals. On-board level translation permits the host side to operate at low digital logic voltages while the cable side uses RS-232 signaling. Charge-pump-assisted drivers produce the required bipolar voltage swings without requiring a separate negative supply. The receiver side restores compatible logic levels while helping the interface withstand the electrical characteristics of a cable-connected RS-232 port. Typical applications include industrial serial controllers, instrumentation, barcode and identification equipment, point-of-sale terminals, security equipment, and embedded control systems. The 1 Mbps capability is useful for short-distance, higher-speed links where the connected RS-232 equipment supports the same rate. The 3.0 V minimum supply also allows use in modern 3.3 V systems, while the 5.5 V maximum supports conventional 5 V equipment. PCB implementation requires careful treatment of the charge-pump capacitor network and the RS-232 connector. Place the four 0.1 µF capacitors close to their associated device pins, use a continuous ground plane, and follow the manufacturer datasheet layout to minimize switching noise and capacitor-loop inductance. Confirm the connector's signal and ground assignments before PCB release. This product summary combines the manufacturer's family specifications, the exact 16-SOIC package identification, lifecycle information, and application-focused guidance. It also distinguishes the readily identifiable same-package replacement from broader functional equivalents so engineers can evaluate board-level compatibility before committing a design to procurement.

詢價 聯絡我們