MAX3232EIDBR - 250kbps Dual RS-232 Transceiver | Texas Instruments (Tape & Reel)
MPN: MAX3232EIDBR ✓ 啟用中MAX3232EIDBR 概覽
An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 levels and receives RS-232 signals before returning them to the host. In the broader hierarchy, the MAX3232EIDBR is an RS-232 transceiver, a line-driver and receiver interface, an interface IC, and ultimately a semiconductor. It is useful where longer cable runs, noise immunity, or compatibility with legacy serial equipment matters more than the low operating voltage and compact size of a modern LVTTL UART.
Key features include two transmit channels, two receive channels, a 3 V to 5.5 V single-supply operating range, and operation up to 250 kbit/s. The integrated charge-pump design permits operation from one supply rail, while the four small external charge-pump capacitors support the bipolar voltage required by TIA/EIA-232-F. The MAX3232E also limits driver output slew rate to a maximum of 30 V/µs, helping reduce electromagnetic interference and ringing on connected cables.
The device architecture separates the host-facing supply and logic interface from the high-voltage RS-232 line pins. This arrangement allows a low-voltage 3.3 V system to communicate with a conventional RS-232 port without a separate negative supply rail. The charge-pump circuitry generates positive and negative voltages internally, and the receiver converts the bipolar line voltage back to a compatible digital signal. Pin-to-pin and supply arrangement should still be checked against the exact alternative being considered.
Typical applications include industrial equipment serial consoles, laboratory instrumentation, point-of-sale terminals, security systems, and service-port connections to legacy computers or controllers. The 250 kbit/s ceiling is suitable for many asynchronous control and diagnostic protocols, although designers should verify that the connected system does not require a faster RS-232 rate. The integrated ESD protection also adds useful robustness at exposed connector pins.
For implementation, place the charge-pump capacitors close to their specified pins and route the RS-232 line traces away from sensitive analog and high-speed digital signals. Keep external protection and chassis-ground decisions separate from signal ground to avoid injecting surge current into the transceiver. Confirm the connector's logic polarity and signal direction against the truth tables in the manufacturer datasheet before final PCB routing.
This page combines device specifications, drop-in alternatives, package details, application guidance, and design considerations to support faster component selection and implementation. It also identifies which parameters require confirmation from the manufacturer datasheet, helping engineers distinguish documented drop-in options from broader functional equivalents.
直接替換替代品,適用於 MAX3232EIDBR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX3232EIDBR (相同外形與佔位) — 差異在於 Package, Supply Voltage Range, Maximum Data Rate, Device Type, ESD Protection.
MAX3232ECDB
✅ 直接替換聯絡詢價
查看資料表 →MAX3232IDB
✅ 直接替換聯絡詢價
查看資料表 →MAX3232CAE+
✅ 直接替換聯絡詢價
查看資料表 →MAX3232EIDBR 規格
| Device Type | Dual RS-232 line driver and receiver |
| Number of Driver Channels | 2 channels |
| Number of Receiver Channels | 2 channels |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| Driver Output Slew Rate | 30 V/µs maximum |
| ESD Protection | ±15 kV IEC ESD protection |
| RS-232 Standard | TIA/EIA-232-F |
| Charge Pump | Dual charge-pump circuit |
| External Charge-Pump Capacitors | 4 capacitors |
| 封裝 | 16-pin SSOP, 5.30 mm width |
| 安裝類型 | Surface mount |
MAX3232EIDBR 16-pin ssop, 5.30 mm width 腳位配置指南
MAX3232EIDBR(16-pin ssop, 5.30 mm width 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX3232EIDBR.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX3232EIDBR 適用於 6 應用s: Industrial Equipment Serial Console, Laboratory Instrument Connectivity, Point-of-Sale Terminal Interface, Security and Access-Control Systems, Legacy Computer Service Port, Embedded UART-to-RS-232 Bridge.
Industrial Equipment Serial Console
The MAX3232EIDBR is well suited to an industrial controller that exposes a serial console over an RS-232 connector. Its 3 V to 5.5 V single-supply operation allows direct use of a 3.3 V embedded system, while the integrated dual charge pump generates the bipolar RS-232 levels without a negative rail. A maximum signaling rate of 250 kbit/s covers many diagnostic and configuration protocols. The ±15 kV IEC ESD rating on the serial-port pins improves protection at an exposed connector, although the PCB should still use a clean ground reference and appropriately routed interface traces. Engineers should verify protocol baud-rate margin, cable length, and the host-side logic levels before finalizing the interface.
推薦
Laboratory Instrument Connectivity
The MAX3232EIDBR can connect a laboratory instrument controller to a conventional RS-232 service or measurement port. Operating from a single 3 V to 5.5 V rail simplifies power planning in compact test equipment, and the dual driver and dual receiver arrangement supports two communication paths when both sides are active. Its 250 kbit/s limit is appropriate for many legacy instrument-control protocols but should be compared with the instrument's maximum supported rate. The driver's controlled slew rate of no more than 30 V/µs helps limit cable-edge energy, while the ±15 kV IEC ESD protection provides useful robustness for a connector that may be touched during routine service.
推薦
Point-of-Sale Terminal Interface
The MAX3232EIDBR fits point-of-sale and peripheral controllers that need a legacy RS-232 link alongside a low-voltage digital processor. The device's two transmitters and two receivers permit RS-232 communication in both directions, while the integrated charge pump eliminates a separate negative supply and reduces board complexity. Its 250 kbit/s maximum data rate is more than adequate for many transaction and configuration channels, though it is not a substitute for a higher-speed differential interface. The ±15 kV IEC ESD protection is particularly relevant at externally accessible POS connectors. Firmware should also support timeout and line-state handling so that a disconnected or partially driven peripheral does not block the terminal.
推薦
Security and Access-Control Systems
The MAX3232EIDBR can provide a wired RS-232 commissioning or diagnostic path in security panels, access-control readers, and camera-support equipment. The 3.3 V-compatible supply range is useful alongside modern embedded processors, while the internal charge-pump arrangement allows operation without a negative supply. Two drivers and two receivers provide flexibility for bidirectional equipment links, and the 250 kbit/s ceiling suits many command and status protocols. For exposed installations, the documented ±15 kV IEC ESD protection adds value at the serial connector, but it does not replace coordinated surge protection, cable routing, or grounding. Firmware should validate received command bytes before changing security-sensitive states.
推薦
Legacy Computer Service Port
The MAX3232EIDBR is useful for adding a modern controller to a legacy computer or embedded service port that still uses RS-232. Its single 3 V to 5.5 V supply operation simplifies level adaptation without requiring a separate negative rail, and the integrated charge pump supplies the compliant bipolar signal internally. The 250 kbit/s maximum rate supports common UART service protocols, while the 30 V/µs maximum driver slew rate limits fast cable transitions. The ±15 kV IEC ESD protection strengthens the connector side of the design. Engineers should check null-modem or straight-through wiring, request-to-send behavior where applicable, ground continuity, and whether the legacy host requires a lower signaling rate than the transceiver maximum.
推薦
Embedded UART-to-RS-232 Bridge
The MAX3232EIDBR provides a compact bridge between a host UART and an RS-232 physical layer. Its two drivers and two receivers support a full-duplex link, while the single 3 V to 5.5 V supply is compatible with embedded 3.3 V platforms. The 250 kbit/s ceiling should be treated as the maximum supported link rate, not as a target for marginal designs; leave timing margin for framing, parity, and system latency. Four external charge-pump capacitors are required, so their placement should follow the manufacturer layout guidance to preserve charge-pump performance. The ±15 kV IEC ESD protection on connection pins improves robustness, but long cables may still benefit from dedicated overvoltage and surge protection.
推薦
推薦產品摘要
工程參考資料,適用於 MAX3232EIDBR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX3232ECDB | MAX3232IDB | MAX3232CAE+ |
|---|---|---|---|---|
| Package | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP | 16-pin SSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
主要差異化特點
- Documented enhanced ESD protection (對比MAX3232IDB)
- Single-rail interface operation (對比MAX3232CAE+)
- Controlled cable transition rate (對比MAX3232ECDB)
設計說明
Place the four charge-pump capacitors directly beside their associated IC pins, using the shortest practical traces and the ground connection shown in the manufacturer layout example. Keep RS-232 driver and receiver traces away from clocks, ADC signals, and switching-regulator nodes. Maintain a continuous signal-ground reference between the transceiver and connector, and route any chassis or surge-protection return current outside the sensitive interface ground path.
Do not treat a shared SSOP footprint as proof that every MAX3232-family ordering code is interchangeable. Before substituting MAX3232ECDB, MAX3232IDB, or MAX3232CAE+, compare the exact pin descriptions, temperature grade, supply limits, data rate, ESD rating, and receiver thresholds. Also confirm connector wiring and logic polarity against the datasheet truth tables; incorrect driver/receiver orientation is a common source of apparently dead communication links.
The MAX3232E limits driver output slew rate to 30 V/µs, but cable edges can still radiate when the board, connector, and ground return are poorly arranged. Use the shortest practical route from the IC to the connector, preserve adjacent return paths, and avoid splitting the ground plane beneath the interface. If the connector is exposed to a long external cable, evaluate a coordinated external surge-protection solution rather than increasing protection capacitance arbitrarily at the driver pins.
合規資訊
The manufacturer material confirms TIA/EIA-232-F operation and ±15 kV IEC ESD protection, but it does not state the requested environmental-compliance statuses. AEC-Q100 is not applicable to this unspecified commercial interface-device ordering option.