產品(46,000+)

MAX334EWE+ - Quad SPST High-Speed Analog Switch, 50 Ohm, 16-SOIC | Maxim Integrated
MAX334EWE+

MAX334EWE+ - Quad SPST High-Speed Analog Switch, 50 Ohm, 16-SOIC | Maxim Integrated

The Analog Devices MAX334EWE+ is a high-speed quad SPST analog switch IC: four independent single-pole single-throw switches with 50 ohm on-resistance packaged in a 16-pin SOIC (SOP-16), powered from +5 V to +30 V single supply or plus/minus 5 V to plus/minus 15 V split supplies with CMOS- and TTL-compatible logic inputs. An analog switch is a solid-state semiconductor device that connects or disconnects an analog signal path under digital control. The switch belongs to the multiplexer family: a single SPST switch is the simplest routing element, and four of them in one package form a quad analog switch that can connect four signal sources to four loads, sample-and-hold front ends, or guard a bus. Like all CMOS analog switches, it sits between the signal world and the digital control world, bridging analog signal conditioning and logic-level control. Key features of the MAX334EWE+ include a 50 ohm on-resistance, high switching speed, break-before-make behavior for all four channels, and logic-compatible control inputs that accept both CMOS and TTL levels. The manufacturer positions it as a direct replacement for the DG201 and DG211, offering one quarter the on-resistance and five times the speed of those earlier parts. The wide supply range accepts laboratory bench rails, industrial 24 V nominal buses, and split supplies without level shifting. Technically, the device uses CMOS switch cells with independent control inputs per channel, so each switch can be steered by a separate logic signal. Low on-resistance keeps insertion loss and load-induced error small in high-impedance measurement paths, while break-before-make sequencing prevents the momentary shorting of two driven nodes that would corrupt a measurement. The MAX334EWE+ is specified for industrial temperature grade and ships in a surface-mount SOP-16 package. Typical uses include precision sample-and-hold circuits in data acquisition systems, signal routing in test and measurement instrumentation, battery-cell and supply monitoring front ends, audio and communications signal path switching, and industrial or automotive signal multiplexing where several analog lines must be selected by a controller. When designing around this device, treat each control input as a digital signal that still requires clean rise and fall times, and keep analog traces short and shielded from the switching control pins. Confirm break-before-make timing against your acquisition system and account for input capacitance and charge injection when the switched node feeds a high-gain amplifier. This page consolidates the switch function, supply and logic compatibility, drop-in replacement options, and practical routing and layout guidance in one place, so an engineer can qualify the MAX334EWE+ for a new board or an existing design revision without cross-checking several documents.

詢價 聯絡我們
MAX335CNG+ - 8-Channel 150Ω SPST Analog Switch | ADI
MAX335CNG+

MAX335CNG+ - 8-Channel 150Ω SPST Analog Switch | ADI

The Analog Devices MAX335CNG+ is a serial-interface, 8-channel single-pole single-throw analog switch with a maximum on-resistance of 150Ω, approximately 100Ω typical, and operation across dual-polarity analog supplies of ±4.5V to ±20V. The device is housed in a 24-pin through-hole PDIP package and provides eight independently controlled switches that conduct equally in either signal direction. An analog switch is a semiconductor that routes analog or digital signals between circuit nodes under electronic control. The MAX335CNG+ belongs to the analog switch and multiplexer hierarchy, where it sits between interface ICs and external signal paths. Its serial digital control reduces the number of logic connections required for eight switch channels, making it useful when a system needs multiple analog lines switched by a microcontroller or embedded processor. The MAX335 offers separate control for all eight SPST switches, symmetrical bidirectional conduction, and nearly constant on-resistance across the analog signal range. These characteristics help preserve signal amplitude and simplify input-impedance calculations. Its serial interface also supports compact designs in instrumentation, industrial control, test equipment, data acquisition, and communication equipment where individual control lines for every channel would consume too many connector or processor pins. According to the manufacturer datasheet, the MAX335 is designed for a broad range of positive and negative supply voltages, making it suitable for industrial signal levels as well as lower-voltage systems. Because the switch resistance remains substantially constant over the analog signal range, engineers can use a consistent resistance model during signal-chain design. The serial control architecture reduces routing complexity while retaining independent access to every switched channel. Typical uses include multiplexed sensor acquisition, programmable gain and filter networks, automated test systems, channel routing in communication equipment, and analog signal isolation. In each case, the MAX335 can place one of two external signals onto a common internal path or disconnect that path when higher impedance is required. The through-hole PDIP-24 package is particularly convenient for prototypes and legacy industrial boards that use socketed or manually assembled components. For reliable layouts, route each switched signal away from the serial clock and data traces, provide a stable ground reference, and keep copper paths short to minimize added resistance and parasitic capacitance. Confirm the supply rails, logic levels, and absolute maximum ratings in the manufacturer datasheet before applying the device to high-voltage signals. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks or making board-level substitutions. This page combines manufacturer specifications, package and interface details, drop-in family options, comparison parameters, and practical design guidance to support component selection, schematic review, PCB implementation, and legacy-board maintenance.

詢價 聯絡我們
MAX335ENG+ - 8-Channel SPST Analog Switch | Analog Devices
MAX335ENG+

MAX335ENG+ - 8-Channel SPST Analog Switch | Analog Devices

The Analog Devices MAX335ENG+ is a serial-controlled, 8-channel single-pole-single-throw analog switch with a 24-pin PDIP package. It provides eight independently controlled switches, a 1:1 signal configuration, and an on-resistance of 100 Ω typical according to the manufacturer datasheet. A distributor listing characterizes the on-resistance as 150 Ω, so system-level calculations should use the value applicable to the selected operating conditions. An analog switch is an integrated semiconductor device that routes electrical signals between terminals under digital control. The MAX335 belongs to the broader analog switch IC category, which falls within interface ICs and semiconductor signal-routing devices. Unlike a mechanical relay, it provides compact, solid-state signal isolation and control. Its serial interface allows a host controller to manage eight switch channels with a compact command structure instead of requiring a dedicated control line for every channel. The principal features of the MAX335ENG+ are eight separately controlled SPST channels, equal signal conduction in either direction, and an on-resistance stated as 100 Ω typical over the analog signal range. The MAX335ENG+ ordering code denotes the 24-pin PDIP configuration and the temperature range identified by the manufacturer’s part-numbering system. These characteristics make it useful where multiple analog or digital signals must be selected, isolated, or routed under software control. The MAX335 uses a serial digital interface for switch control. Because all eight switches share the same serial control mechanism, the device can reduce control-line count compared with a bank of discrete mechanically controlled analog switches. The on-resistance remains approximately constant across the analog signal range, helping simplify impedance calculations when the switch is placed in series with a source or load. Signal integrity still depends on capacitance, bandwidth, layout, source impedance, and the frequency content carried by the selected channel. Typical uses include test and measurement signal routing, communication equipment, industrial control interfaces, data-acquisition systems, and embedded control systems that need to connect one signal source to one of several destinations. The eight-channel SPST organization can also implement isolation between a shared analog bus and peripheral circuits. It is especially useful where compact control, bidirectional conduction, and individually addressable channels are more important than ultra-low resistance. When laying out a MAX335ENG+ circuit, keep analog traces short and provide a clean ground reference because the serial interface and switched signals must not share noisy return paths. Confirm the control protocol and timing from the manufacturer datasheet before writing firmware. Treat the stated 100 Ω typical on-resistance as a real impedance in the signal path and include its attenuation when calculating sensor, amplifier, or ADC input networks.

詢價 聯絡我們
MAX335EWG+ - 8-Channel SPST Serial Switch | Analog Devices
MAX335EWG+

MAX335EWG+ - 8-Channel SPST Serial Switch | Analog Devices

The Analog Devices MAX335EWG+ is an 8-channel single-pole single-throw analog switch with a serial digital interface, 150 ohm on-resistance, and operation from -15 V to +20 V supply voltage in a 24-pin WSOIC package. The device provides eight separately controlled switches that conduct equally in either direction, making it suitable for routing analog signals in test, measurement, industrial, and data-acquisition systems. An analog switch is a semiconductor interface that connects or disconnects signal paths under digital control. The MAX335 belongs to the broader CMOS analog-switch and interface-IC hierarchy, where the switch handles analog signal routing while a serial interface controls channel state. Each SPST channel provides one normally open path, allowing external circuitry to select among multiple signals without redesigning the analog path. The MAX335EWG+ features a nominal 150 ohm on-resistance, approximately 400 ns switching times, 90 dB isolation, and an industrial operating-temperature range from -40 C to +85 C. Its serial control reduces the number of external control pins required when multiple channels must be managed in a compact system. The analog signal path is designed to maintain consistent resistance across the specified signal range. Use the device when a system needs eight independently addressable SPST routes and can accept a serial command interface. A typical implementation places the switch between a sensor or measurement source and a downstream analog front end, allowing the controller to select test channels or isolate signal paths. The -15 V to +20 V supply range supports both positive and negative analog signal environments. PCB layout should keep analog traces short, provide a stable ground reference, and place decoupling capacitors close to the supply pins. The serial interface requires correct logic levels and signal timing; the manufacturer datasheet should be used for pin assignment and serial protocol details. Confirm the maximum signal voltage, current, and switching conditions before finalizing the design. This product page consolidates the MAX335EWG+ electrical specifications, package information, sourcing guidance, and practical design considerations into one reference for engineers evaluating serial-controlled analog routing.

詢價 聯絡我們
MAX336EPI+ - 16:1 Low-Leakage CMOS Multiplexer | Analog Devices
MAX336EPI+

MAX336EPI+ - 16:1 Low-Leakage CMOS Multiplexer | Analog Devices

Analog Devices MAX336EPI+ is a 16-channel, single 16:1 CMOS analog multiplexer with 400 ohm on-resistance, low-leakage characteristics, and operation from 4.5 V to 30 V in a 28-pin PDIP package. It is designed for routing multiple analog signals through a shared circuit while limiting channel-selection errors, leakage, and signal distortion. An analog multiplexer is an input-routing semiconductor that selects one of several analog inputs and connects it to a common output. The MAX336 belongs to the CMOS analog switch and multiplexer hierarchy within broader interface ICs. Its 16:1 configuration reduces the number of physical signal paths required in instrumentation, measurement, control, and data-acquisition systems where many sensor or test inputs must be scanned sequentially. Key features include a single 16:1 configuration, 400 ohm on-resistance, low-leakage CMOS operation, and a 4.5 V to 30 V single-supply range. The MAX336 family also provides a dual 8-channel configuration option and is specified for low charge injection, with 3.5 pC typical. According to the Analog Devices product page, electrostatic-discharge protection exceeds 2000 V using method 3015.7, helping protect sensitive analog nodes during handling and system integration. The MAX336 is implemented as a CMOS analog switch with controlled complementary addressing and break-before-make behavior expected of the MAX336/MAX337 family. Its low-leakage characteristic is particularly valuable when measuring high-impedance sources because off-channel leakage can create an error proportional to source impedance. The 400 ohm on-resistance must also be included in source-impedance and gain-error calculations, especially for instrumentation front ends with long sensor leads. Typical uses include battery-cell monitoring, programmable instrumentation, industrial control, automated test equipment, data acquisition, and analog signal routing. The device can consolidate 16 measurement channels into one signal chain while the surrounding system applies an address and measures each selected input. It is also suitable where leakage, rather than switching speed, is the primary concern. PCB design should keep the selected analog path short and place protection and filtering components near the relevant pins. Verify input levels, supply range, address timing, and off-channel leakage against the end-equipment accuracy budget. A PDIP package favors through-hole prototyping and repair but occupies more board area than surface-mount alternatives. This product page combines manufacturer specifications, package information, sourcing guidance, application analysis, and honest replacement evaluation. It also highlights where pin-to-pin alternatives are technically credible, avoiding the inclusion of parts that require a different footprint or materially different switching architecture.

詢價 聯絡我們
MAX337CPI+ - Dual 8-Channel CMOS Multiplexer | Analog Devices
MAX337CPI+

MAX337CPI+ - Dual 8-Channel CMOS Multiplexer | Analog Devices

Analog Devices MAX337CPI+ is a dual, 8-channel, low-leakage CMOS analog multiplexer with a 400 ohm maximum on-state resistance, operating from 4.5 V to 30 V in a 28-pin PDIP package. The device routes two independent groups of eight analog inputs to their respective outputs using digital address and enable control signals. An analog multiplexer is an interface IC that connects one selected input to a shared output. In the multiplexer's functional hierarchy, the MAX337CPI+ belongs to the analog switch and multiplexer class, then to interface ICs, and finally to the broader semiconductor category. This architecture reduces the number of signal paths required by test equipment, data-acquisition systems, industrial controllers, and measurement instruments while preserving controlled access to multiple analog inputs. Key characteristics include a dual 8-channel configuration, low leakage, 400 ohm maximum on resistance, and operation across a 4.5 V to 30 V supply range. The device supports a maximum dual supply of ±20 V, enabling signal paths near the limits of its supply architecture when suitable protections are applied. Its commercial operating-temperature range is 0°C to 70°C, while maximum power dissipation is 1.14 W. The MAX337CPI+ uses CMOS multiplexing to route analog signals with digital address control. Its two 8:1 sections are controlled by address inputs and separate enable logic, allowing a system to select channels independently or apply coordinated selection across both banks. The 28-pin PDIP package provides through-hole accessibility and is suitable for prototypes, legacy industrial equipment, and instruments assembled with manual insertion. Typical uses include automated test systems, data-acquisition units, process-control panels, instrumentation, and analog signal-routing boards. In each system, the multiplexer reduces wiring complexity by sharing output circuitry among multiple sensed or measured channels. Designers should account for source impedance, settling time, injected switching noise, and the voltage limits of the connected signals. For layout, keep analog input and output traces away from fast digital control lines, use a quiet ground reference, and terminate unused channels according to the application architecture. Confirm signal amplitude, common-mode range, supply polarity, address timing, and power dissipation before committing the 28-pin footprint to a new PCB. This product page consolidates the device function, electrical limits, package details, purchasing guidance, and design considerations into one engineering reference. It also distinguishes verified functional characteristics from the parameters engineers should confirm in the manufacturer datasheet before layout or production release.

詢價 聯絡我們
MAX337CWI+ - Dual 8:1 CMOS Multiplexer | Analog Devices
MAX337CWI+

MAX337CWI+ - Dual 8:1 CMOS Multiplexer | Analog Devices

Analog Devices MAX337CWI+ is a dual 8:1 CMOS analog multiplexer with 400 ohm on-resistance in a 28-pin SOIC package. The device routes one of eight analog inputs on each multiplexer section to a common output, providing 16 switch channels in one IC. Its low-leakage design makes it suitable for precision signal selection, measurement systems, and instrumentation where minimizing input loading is important. An analog multiplexer is a semiconductor switch that connects one selected input to a shared output. A dual 8:1 CMOS multiplexer expands two independent groups of eight inputs into two common outputs. This hierarchy places the MAX337CWI+ within analog switches, interface ICs, and general-purpose signal-routing devices. It reduces the number of external routing components while allowing one controller to select among multiple analog signals. The MAX337 family is identified as a 16-channel dual 8-channel, low-leakage CMOS analog multiplexer. According to the manufacturer product page, MAX337 is in production, and the manufacturer datasheet describes the device as a monolithic CMOS analog multiplexer. Its 8:1 configuration uses address-control inputs to select one input per section and route it to the corresponding common output. The listed 400 ohm on-resistance provides the principal quantified electrical characteristic for this exact listing. It determines the series loss and interaction between the selected source and destination when the switch is on. Low leakage is especially important when the mux precedes high-impedance analog nodes, because leakage current can create an error voltage proportional to the input source impedance. Typical uses include battery-cell monitoring, sensor multiplexing, data acquisition, automated test equipment, and laboratory instruments. The dual architecture is particularly useful when two related analog quantities must be selected independently, such as paired sensor outputs or two channels within a multichannel measurement system. The same common-output arrangement can also be used to share a downstream amplifier or converter between several inputs. Designers should treat the address controls as digital signals while paying attention to the analog signal range, source impedance, and leakage of the connected sources. Place bypass and signal-conditioning components close to the mux pins, keep analog routing away from high-current switching nodes, and use a suitable common-ground strategy. Review the manufacturer pin-description table and operating limits before finalizing the board layout. This page combines the manufacturer overview, distributor identification, package details, cross-reference results, and practical selection guidance for the MAX337CWI+. It also distinguishes a verified dual 8:1 replacement candidate from devices that use a different package or channel architecture, helping engineers narrow replacement decisions without confusing functional similarity with true drop-in compatibility.

詢價 聯絡我們
MAX3380ECUP+ - 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3380ECUP+

MAX3380ECUP+ - 2Tx/2Rx RS-232 Transceiver | Analog Devices

Analog Devices MAX3380ECUP+ is a 2-transmitter, 2-receiver RS-232 transceiver operating from +2.35V to +5.5V, with 15kV ESD protection on both logic and RS-232 I/O pins. The device is housed in a 20-pin TSSOP package and supports low-power RS-232 communication systems requiring one interface per port. An RS-232 transceiver is an interface IC that converts between single-ended TTL/CMOS logic levels and differential bipolar RS-232 signal levels. The MAX3380ECUP+ integrates two transmit channels and two receive channels, allowing a compact design to connect a UART, embedded controller, or industrial communications equipment to an RS-232 port. Its dual charge-pump design allows the RS-232 output levels to operate from a supply as low as +2.35V while remaining compatible with +5.5V systems. Key features include a +2.35V to +5.5V operating range, two transmit and two receive channels, enhanced ESD protection rated at 15kV on both sides of the interface, and support for EIA/TIA-232 and V.28/V.24 communication requirements. The low-power architecture is suitable for battery-powered equipment and portable serial interfaces where supply current and board area are important design constraints. The MAX3380ECUP+ uses integrated charge-pump circuitry to generate the positive and negative voltage levels required by RS-232 transmitters. Its low-dropout transmitter output stage is designed to preserve compliant RS-232 output levels over the full supply range, including when the supply is close to the minimum operating voltage. The device also provides enhanced ESD protection at the logic and RS-232 pins, helping protect the connected UART or transceiver from electrostatic discharge events. Typical applications include industrial serial controllers, point-of-sale terminals, test equipment, instrumentation, embedded control systems, and battery-powered communications products. The two-transmitter, two-receiver arrangement is useful when a product needs to monitor one serial connection while transmitting on another without using two separate transceiver packages. The TSSOP-20 footprint also supports compact PCB layouts in equipment with limited connector space. When laying out the MAX3380ECUP+, place the charge-pump capacitors and interface bypass capacitors close to their associated pins. Keep RS-232 traces short and route them away from sensitive logic and clock signals. Confirm the external capacitor values, supply voltage, and UART logic levels against the manufacturer datasheet before releasing a PCB layout. This product data combines the manufacturer interface overview with structured application guidance, drop-in replacement information, comparison parameters, and practical layout notes. It is intended to help engineers evaluate the MAX3380ECUP+ for compact, low-voltage RS-232 interfaces while keeping the implementation focused on verified electrical and package characteristics.

詢價 聯絡我們
MAX3380ECUP+T - 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3380ECUP+T

MAX3380ECUP+T - 2Tx/2Rx RS-232 Transceiver | Analog Devices

The Analog Devices MAX3380ECUP+T is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35 V to +5.5 V operation, with a 20-pin TSSOP package and enhanced electrostatic-discharge protection on both logic and RS-232 pins. It supports EIA/TIA-232 and V.28/V.24 communication interfaces while operating from a 1.65 V logic reference where required. An RS-232 transceiver is an interface IC that converts between single-ended TTL/CMOS logic signals and differential bipolar RS-232 signals. It belongs to the interface-IC hierarchy, connecting UART, UART-compatible controllers, microcontrollers, and industrial peripherals to physical communication links. Transceivers combine driver and receiver functions in one package, reducing board area and simplifying bidirectional serial-port implementations. The MAX3380ECUP+T provides two transmit channels and two receive channels, allowing two serial ports to share one device. Its +2.35 V to +5.5 V supply range accommodates modern 3.3 V and 5 V systems, while the VL pin provides logic-level interoperability in mixed-voltage environments down to 1.65 V. The manufacturer describes enhanced ESD protection on the TTL and RS-232 sides, with the distributor listing identifying 15 kV ESD protection on I/O and logic pins. The device combines low-power operation with high data-rate capability, making it suitable for compact communications equipment. Its integrated charge-pump circuitry supports RS-232 signal generation without a separate external DC-DC converter. Logic input and output levels are referenced to VL, allowing the interface thresholds to track a compatible mixed-logic supply rather than being tied to one fixed rail. Typical uses include industrial serial controllers, point-of-sale equipment, test and measurement instruments, medical-device consoles, security systems, and other embedded systems that exchange data over RS-232. A system can connect two UART channels to the MAX3380ECUP+T while providing shared ground wiring, proper signal polarity, and compliant cable termination. PCB layout should keep RS-232 traces away from clocks, switching supplies, and high-speed digital nets. Confirm logic thresholds against the connected UART voltage, observe the manufacturer’s charge-pump capacitor requirements, and provide the specified supply and bypass capacitance close to the device pins. This page combines the manufacturer interface description, package and ordering information, drop-in alternatives, comparison parameters, and practical PCB guidance to support faster component selection and implementation.

詢價 聯絡我們
MAX3380EEUP+ - 2/2 RS-232 Transceiver | Analog Devices
MAX3380EEUP+

MAX3380EEUP+ - 2/2 RS-232 Transceiver | Analog Devices

Analog Devices MAX3380EEUP+ is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35 V to +5.5 V operation, with 15 kV ESD protection on both the RS-232 and logic pins and support for data rates up to 460 kbps. The device is offered in a 20-pin TSSOP package. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar RS-232 signals. It belongs to the transceiver class, then to the broader interface IC and semiconductor hierarchy. This bidirectional interface is useful when equipment must communicate over longer cable distances, tolerate ground-offset differences, or meet the electrical characteristics associated with EIA/TIA-232 and V.28 communications. The MAX3380EEUP+ uses a low-dropout transmitter output stage and a dual charge pump. These features allow RS-232-compatible output levels from supplies below +3.1 V and down to +2.35 V without increasing supply current when the supply lies within that range. Its +5.5 V maximum operating voltage also makes it suitable for systems powered from a single lithium-ion cell or a low-voltage regulated rail. The four-driver, four-receiver naming in some listings refers to two transmit channels and two receive channels rather than four independent full-duplex ports. Both RS-232 I/O pins and logic-side pins receive enhanced electrostatic-discharge protection. Typical system-level uses include data acquisition equipment, industrial controllers, service interfaces, embedded serial ports, and instrumentation that requires a compact, low-voltage RS-232 connection. For board design, treat the transmitter outputs and receiver inputs as externally exposed communication pins even when the logic-side pins are protected. Keep the interface connector and cable path away from sensitive analog circuitry, provide the required bypass capacitance close to the supply pins, and route the differential transmission traces as a pair. The transmitter should connect to the remote RS-232 port through protection and signal-conditioning components appropriate to the required surge and ESD levels. MAX3380EEUP+ is appropriate when a board needs two RS-232 receive channels and two RS-232 transmit channels from a compact, low-power interface IC. Verify cable length, data rate, connector protection, and grounding before deployment. This page combines the product specifications, qualified package details, sourcing information, replacement guidance, and practical RS-232 design considerations into a focused engineering reference.

詢價 聯絡我們
MAX3381ECUP+ - 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3381ECUP+

MAX3381ECUP+ - 2Tx/2Rx RS-232 Transceiver | Analog Devices

Analog Devices MAX3381ECUP+ is a 2-transmitter, 2-receiver RS-232 interface transceiver with a +2.35 V to +5.5 V supply range, 15 kV ESD protection on I/O and logic pins, and a 20-TSSOP package. It combines EIA/TIA-232 and V.28/V.24 communication functions with low power requirements and high data-rate capability. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 equipment. Within the interface hierarchy, it belongs to the RS-232 transceiver class, communication interface IC family, and broader semiconductor category. Two transmitters and two receivers allow one device to support a complete point-to-point or multi-drop serial connection when the system bus rules are observed. The MAX3381ECUP+ provides 15 kV ESD protection on both its RS-232 I/O pins and logic pins. This protection is particularly useful in industrial, industrial-control, and equipment environments where cables can be touched or exposed to electrostatic discharge. Its 2.35 V minimum supply voltage also supports systems that cannot rely on a regulated 3.3 V or 5 V rail. The MAX3381E family is designed for low-power operation while retaining high data-rate performance. The integrated charge-pump circuitry required for RS-232 voltage generation is contained in the interface IC, reducing the number of external components needed for a working communication port. The MAX3381ECUP+ is identified as a 2/2 full RS-232 transceiver in a 20-TSSOP package. Typical applications include serial service consoles, data-acquisition equipment, industrial control links, test and measurement instruments, and embedded systems that communicate with legacy RS-232 peripherals. The dual-channel arrangement is useful for designs requiring two serial paths, or one link in each direction, without using two separate interface devices. PCB implementation should preserve the device's pinout and follow the manufacturer layout guidance. Place the required passives close to their associated pins, route the RS-232 traces away from sensitive analog and clock signals, and use suitable protection and grounding practices for cables entering the enclosure. Confirm the exact pin functions and external-component values against the manufacturer datasheet before releasing the layout. This product page consolidates the verified operating range, channel configuration, ESD rating, package information, same-footprint alternatives, and application-oriented design guidance. It is intended to help engineers evaluate the MAX3381ECUP+ quickly while keeping the final schematic, PCB, and component decisions grounded in manufacturer documentation.

詢價 聯絡我們
MAX3381ECUP+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3381ECUP+T

MAX3381ECUP+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3381ECUP+T is a 2-transmitter, 2-receiver full-duplex RS-232 transceiver operating from 2.35V to 5.5V, supporting data rates up to 250kbps and providing 15kV ESD protection on I/O and logic pins in a 20-TSSOP package. It combines EIA/TIA-232, V.28, and V.24 interface requirements with low-power operation and integrated level translation. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into digital logic levels. In the broader electronics hierarchy, an RS-232 transceiver belongs to interface ICs and line-driver and receiver devices, where it protects a host controller from the voltage range and electrostatic-discharge exposure of a serial connection. The MAX3381E family supports two transmit channels and two receive channels, allowing full-duplex communication through one package. Its 2.35V minimum supply voltage supports modern low-voltage embedded systems, while the 5.5V maximum accommodates conventional 5V equipment. The 250kbps maximum data rate is suitable for industrial control links, point-of-sale equipment, data acquisition, and service interfaces. Integrated charge-pump circuitry generates the bipolar voltage required to transmit RS-232-compatible levels from a single low-voltage supply. According to the manufacturer datasheet, enhanced electrostatic-discharge protection is provided on both the TTL and RS-232 sides, covering the 15kV ESD-protected I/O and logic pins identified for this device. Typical uses include industrial serial controllers, programmable-logic or microcontroller UART links, instrumentation, and embedded control systems. The two transmitters can support separate outbound channels, while the two receivers allow simultaneous inbound monitoring or redundant communication paths when the connected system requires them. PCB design should provide a solid ground plane, place charge-pump and interface components close to the device, and preserve adequate clearances around connected RS-232 lines. Decoupling capacitors should be placed directly beside the supply pins. The 20-TSSOP footprint is compact, but its narrow lead pitch requires careful inspection and reliable assembly processes. This product page combines operating limits, interface characteristics, application guidance, package details, and same-family drop-in alternatives to support component selection and PCB design before an RS-232 interface is committed to production.

詢價 聯絡我們
MAX3381EEUP+ 2Tx/2Rx RS-232 Transceiver | Analog Devices
MAX3381EEUP+

MAX3381EEUP+ 2Tx/2Rx RS-232 Transceiver | Analog Devices

Analog Devices MAX3381EEUP+ is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35 V to +5.5 V operation, with 1 uA supply current, 460 kbps data rate, and ±15 kV ESD protection on its I/O and logic pins. The device is packaged in a 20-pin TSSOP. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar RS-232 signals. It belongs to the transceiver and line-driver hierarchy within interface ICs, allowing equipment with TTL or CMOS logic ports to communicate with RS-232 equipment over a wired serial link. The MAX3381E combines two transmit channels, two receive channels, level translation, and electrostatic-discharge protection in one package. The MAX3381EEUP+ supports supply voltages from +2.35 V to +5.5 V, making it suitable for systems that cannot provide a conventional +5 V rail. Its 460 kbps maximum signaling rate handles common point-to-point serial-control links, while its 1 uA supply current supports low-power equipment. The ±15 kV ESD rating applies to both the RS-232 I/O pins and the logic pins. The MAX3381E family implements powered EIA/TIA-232 and V.28/V.24 communication interfaces. Powered operation means the device includes the charge-pump circuitry required to generate the bipolar voltage levels used by RS-232. This integration reduces the external discrete components normally needed around separate line drivers and receivers, although charge-pump capacitors and interface filtering still require careful PCB planning. Typical uses include industrial control consoles, laboratory instruments, data-acquisition equipment, point-of-sale terminals, and service-port adapters. The two transmitter and two receiver channels suit links requiring two serial paths, while the broad supply-voltage range supports both 3.3 V and 5 V system logic. Cable routing and connector selection remain important because RS-232 is designed for point-to-point communication rather than long multipoint networks. For a new layout, place the device close to the protected connector and route each RS-232 line directly toward its connector pin with a short path. Keep logic-side traces away from the unprotected connector side of the interface. Confirm the device's enable, shutdown, receiver-output, and driver-input states during startup so that unused channels do not create bus contention. This product record combines the manufacturer's MAX3381E family information with package, interface, speed, power, and ESD characteristics for engineering selection. It also provides verified same-package replacement context, practical layout guidance, and application-oriented comparisons that support faster component evaluation before schematic capture.

詢價 聯絡我們
MAX3381EEUP+T - 2/2 RS-232 Transceiver | Analog Devices
MAX3381EEUP+T

MAX3381EEUP+T - 2/2 RS-232 Transceiver | Analog Devices

Analog Devices MAX3381EEUP+T is a 2-transmitter, 2-receiver RS-232 transceiver operating from +2.35 V to +5.5 V, with 15 kV ESD protection on I/O and logic pins, in a 20-pin TSSOP package. The interface supports EIA/TIA-232 and V.28/V.24 communication while operating from a low 1 µA supply current. An RS-232 transceiver is an interface IC that converts low-voltage digital logic signals into RS-232 voltage levels and converts received RS-232 signals back into logic-compatible levels. It belongs to the transceiver and driver/receiver hierarchy, bridging UART, UART-compatible controller, and computer I/O logic with external serial cables. This bidirectional level-shifting function allows a compact system to communicate through a longer-distance, noise-tolerant serial interface. The MAX3381EEUP+T provides two transmit channels and two receive channels, supporting full-duplex point-to-point serial links. Its +2.35 V to +5.5 V operating range supports low-voltage logic systems as well as conventional +5 V equipment. The manufacturer's product page identifies 15 kV ESD protection on both I/O and logic pins, helping protect sensitive interface circuits when cables are connected or disconnected. The MAX3380E and MAX3381E families combine low power consumption with high data-rate capability. The MAX3381E variant is specified for production availability, and its enhanced ESD protection applies to both the RS-232 side and the logic pins. Independent transmit and receive channels allow full-duplex operation when the connected system assigns one driver and one receiver to each communication path. Typical uses include industrial control links, point-of-sale equipment, data-cable interfaces, instrumentation, and embedded serial ports. The dual transmitter arrangement can support two outbound RS-232 signals, while the dual receivers can monitor two incoming signals. In designs using a UART, the device can translate between the controller's logic-level pins and the voltage levels required by an RS-232 cable. When laying out the circuit, place the device close to the RS-232 connector and route driver and receiver traces away from sensitive analog or high-speed digital paths. Verify the connector's signal and ground assignments, provide the required supply bypassing, and maintain adequate board spacing to reduce surge-current exposure at the protected pins. This product page brings together the manufacturer's core electrical characteristics, package information, verified drop-in relationships, and practical interface-layout guidance. It is intended to help engineers evaluate the MAX3381EEUP+T for low-voltage RS-232 links, compare documented replacements, and plan protection and layout before releasing a PCB design.

詢價 聯絡我們
MAX3384ECAP - 250kbps ESD-Protected RS-232 | Analog Devices
MAX3384ECAP

MAX3384ECAP - 250kbps ESD-Protected RS-232 | Analog Devices

Analog Devices MAX3384ECAP is a low-power true RS-232 transceiver with two transmitters and two receivers, operating from a 3.0V to 5.5V single supply and supporting data rates up to 250kbps. Every transmitter output and receiver input provides electrostatic-discharge protection to ±15kV. The device is packaged in a 20-pin SSOP with a 0.65mm pitch. A true RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar RS-232 signals. It belongs to the broader communication-interface hierarchy: RS-232 transceiver → line driver and receiver → interface IC → semiconductor. The MAX3384ECAP combines transmit and receive functions in one package, allowing a compact design to bridge a modern controller or microcontroller with a legacy RS-232 link. The 3.0V to 5.5V operating range supports both 3.3V and 5V digital systems while avoiding the higher supply requirement associated with some older RS-232 devices. Its operation up to 250kbps makes it suitable for data acquisition, industrial control, point-of-sale equipment, and embedded systems that transfer more information than a low-speed serial link. The integrated ±15kV ESD protection strengthens the external interface against electrostatic discharge events. The MAX3384ECAP provides two transmit channels and two receive channels in a single 20-pin SSOP. This channel density allows one transceiver to serve two independent RS-232 directions or multiple device connections. A 3.3V-compatible supply range also simplifies mixed-voltage designs in which the controller core operates below 5V, while the RS-232 interface remains powered from the same rail. Typical applications include industrial serial controllers, point-of-sale terminals, access-control equipment, security systems, laboratory instruments, and embedded data-collection systems. The combination of four I/O channels, a 250kbps maximum signaling rate, low-power operation, and ±15kV interface protection addresses designs that require compact integration without the supply voltage of a legacy 5V-only RS-232 implementation. Designers should pay attention to the device's 0.65mm-pitch SSOP footprint and verify every signal and power connection against the manufacturer pin-description table before layout release. Keep the RS-232 connector-side traces away from sensitive logic where practical, and provide the external charge-pump and interface components specified by the manufacturer datasheet for the selected operating configuration. This product overview combines the MAX3384ECAP's principal electrical, packaging, protection, and interface characteristics with pin-compatible replacement guidance and practical PCB considerations. It supports faster component selection by separating application fit, channel requirements, supply compatibility, and package constraints into directly comparable engineering factors.

詢價 聯絡我們
MAX3384ECWN+ - 250kbps RS-232 Transceiver | Analog Devices
MAX3384ECWN+

MAX3384ECWN+ - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3384ECWN+ is a 3.0V-powered, 2/2 RS-232 transceiver supporting data rates up to 250kbps in a 20-pin SSOP package. It provides two transmit channels, two receive channels, low-power operation, and enhanced electrostatic-discharge protection for reliable point-to-point serial interfaces. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 levels back into digital logic. It belongs to the transceiver hierarchy within interface ICs, providing the physical signaling layer between data-processing equipment and a cable-connected peripheral or system. The MAX3384ECWN+ implements the EIA/TIA-232 and V.28/V.24 signaling requirements described for this device family. The principal features include operation from a 3.0V to 5.5V supply, operation up to 250kbps, two transmit outputs, two receive inputs, and enhanced ESD protection. Low-power requirements make the device suitable for systems in which interface circuitry must coexist with low-voltage digital logic. The manufacturer describes protection on both transmitter outputs and receiver inputs, which is important when cables may be connected, disconnected, or exposed to electrostatic discharge. The MAX3384ECWN+ combines true RS-232 line-driver and receiver functions in one integrated circuit. Its powered-down behavior reduces power consumption when the associated subsystem is inactive. Because the interface operates from a single low-voltage supply while generating compliant RS-232 levels, it can simplify designs that would otherwise require separate external line drivers, receivers, and protection networks. Typical uses include industrial control consoles, point-of-sale terminals, test equipment, instrumentation, and embedded systems that communicate with RS-232 peripherals through cables. The 250kbps capability is useful for moderate-speed serial links, while the integrated two-channel transmitter and receiver arrangement reduces the number of components required for bidirectional or multiport serial interfaces. The principal design consideration is the difference between RS-232 and TTL-level signaling. The MAX3384ECWN+ is intended for the RS-232 side of the connection; it does not directly accept or produce standard TTL or CMOS logic levels. Layout should preserve short return paths and appropriate grounding, while external protection and cable-length considerations should follow the manufacturer's interface guidance. This product page combines the device's core electrical characteristics, verified package information, practical application guidance, and documented same-family replacement options. It also distinguishes true pin-compatible alternatives from broader RS-232 interface products that may use a different package, voltage rating, feature set, or channel arrangement.

詢價 聯絡我們
MAX3384ECWN+T - 250kbps RS-232 Transceiver | Analog Devices
MAX3384ECWN+T

MAX3384ECWN+T - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3384ECWN+T is a 2/2 RS-232 transceiver with a 3.0V to 5.5V supply range, data rates up to 250kbps, and 15kV ESD protection, housed in an 18-pin SOIC package. It combines two transmitters and two receivers in one device, providing bidirectional serial-interface conversion for equipment that communicates through EIA/TIA-232 and V.28/V.24 links. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 levels and converts incoming RS-232 signals back into digital logic levels. It belongs to the interface IC hierarchy, where the transceiver performs the physical signal conversion between a host controller or UART and an RS-232 port. This integration reduces the number of discrete line-driver and receiver components required at the board level. The MAX3384ECWN+T operates from 3.0V to 5.5V, supports data rates up to 250kbps, and provides 15kV ESD protection. The Analog Devices manufacturer page specifies that all transmitter outputs and receiver inputs are protected. Its 18-pin SOIC package supports conventional surface-mount assembly and is suitable for industrial-control, communications, instrumentation, and embedded-system interfaces operating across 0°C to 70°C. The device uses two transmitters and two receivers, allowing two serial channels or full-duplex operation depending on how the interface pins are connected. Because it is a true RS-232 transceiver rather than a differential RS-422 or RS-485 device, its voltage levels and application role are not interchangeable with those bus standards. The 250kbps maximum data rate is suitable for legacy serial equipment, control consoles, POS systems, and industrial peripherals that use EIA/TIA-232. Typical applications include point-of-sale terminals, security and access-control equipment, test and measurement instruments, industrial controllers, and service-console interfaces. The integrated ESD protection is particularly valuable where an exposed serial cable can introduce electrostatic discharge into a control board. The 3.0V minimum supply voltage also helps the device operate alongside modern low-voltage digital systems without requiring a dedicated 5V-only interface rail. PCB design should preserve the datasheet-recommended supply and bypass-capacitor placement while keeping unprotected external connector wiring away from sensitive traces. Confirm the RS-232 signal levels and data direction in the system schematic, and verify that the 250kbps rating covers the required baud rate with suitable margin. Use the manufacturer pin-description table and pinout drawing when assigning connector and logic-net connections. This page combines the manufacturer interface description, distributor package information, replacement guidance, parameter comparisons, and practical PCB considerations in a form intended to accelerate component selection and hardware design.

詢價 聯絡我們
MAX3384EEAP - 3V RS-232 Transceiver, 250kbps | Analog Devices
MAX3384EEAP

MAX3384EEAP - 3V RS-232 Transceiver, 250kbps | Analog Devices

The Analog Devices MAX3384EEAP is a 3V-powered EIA/TIA-232 and V.28/V.24 communications transceiver with two drivers and two receivers in a 20-pin SSOP package. It supports operation from 3V to 5.5V, delivers data rates up to 250kbps, and provides enhanced electrostatic discharge protection on the transmitter outputs and receiver inputs. The device is designed for low-power RS-232 links where supply voltage, communication speed, and transient protection are the primary design requirements. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 bipolar levels and converts received RS-232 levels back into CMOS-compatible logic. The MAX3384EEAP belongs to the interface IC hierarchy alongside serial transceivers, line drivers, and level-shifting ICs. Its two-driver, two-receiver arrangement supports full-duplex point-to-point communication, including flow-control lines between two data-terminal systems. Key features include a 3V to 5.5V supply range, operation up to 250kbps, low-power operation with shutdown and receiver active-low features, and ±15kV air-gap ESD protection on all transmitter outputs and receiver inputs. Contact discharge protection is rated at ±8kV using the IEC 1000-4-2 test method. These protection levels are important when the connector is exposed to cable discharge events or an industrial noise environment. The MAX3384E uses charge-pump circuitry to generate the bipolar voltage required by the RS-232 drivers, allowing operation from a single low-voltage supply. This architecture eliminates the need for a separate negative supply rail. The resulting single-supply implementation reduces board complexity in systems that already operate from 3.3V or 5V, while the driver stage provides the voltage swing expected by RS-232 receivers. Typical applications include industrial serial consoles, point-of-sale terminals, data-acquisition equipment, instrument control links, and embedded systems that communicate with legacy RS-232 peripherals. The 250kbps maximum data rate supports modern UART traffic while remaining compatible with the slower signaling commonly used by V.28 and V.24 equipment. The package is also suitable for compact control boards where connector access is limited. When laying out the circuit, place the device close to the RS-232 connector to minimize the length of unprotected traces between the IC and connector. Follow the pin-description and decoupling guidance in the manufacturer datasheet, and maintain the recommended charge-pump capacitor connections. Do not treat the internal ESD protection as a substitute for a properly designed external surge-protection network when cables leave the enclosure. This page combines device specifications, same-footprint drop-in alternatives, pin-level guidance, and application-focused design notes. It also highlights the MAX3384EEAP's balance of 3V supply operation, 250kbps throughput, low-power features, and enhanced IEC 1000-4-2 ESD protection for engineers evaluating a modern single-supply RS-232 interface.

詢價 聯絡我們
MAX3385ECAP - 250kbps True RS-232 Transceiver | Analog Devices
MAX3385ECAP

MAX3385ECAP - 250kbps True RS-232 Transceiver | Analog Devices

The Analog Devices MAX3385ECAP is a 2/3 transceiver with integrated charge pump and true RS-232 line drivers and receivers, operating from 3.0V to 5.5V at data rates up to 250kbps. The device is packaged in a 20-pin SSOP and provides 15kV ESD protection on its serial interface. An RS-232 transceiver is an interface integrated circuit that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 equipment. A line driver translates logic states into RS-232-compatible outputs, while a line receiver performs the reverse conversion. The MAX3385ECAP integrates one driver and two receivers, commonly described as a 2/3 transceiver, for asymmetric point-to-point communication links. The MAX3385ECAP supports supply voltages from 3.0V to 5.5V, allowing operation from common 3.3V and 5V systems. Its maximum guaranteed data rate is 250kbps, making it suitable for point-to-point industrial control, instrumentation, data acquisition, and embedded equipment. The 15kV ESD rating strengthens its suitability for connectors and cables exposed to electrostatic discharge. Its dual charge-pump architecture generates the positive and negative voltages required for true RS-232 output levels without a separate negative supply rail. The manufacturer datasheet states that four 0.1uF capacitors are sufficient for operation from a 3.3V supply. A proprietary low-dropout transmitter output stage helps maintain compliant output levels across the supported supply range while controlling power consumption. Typical uses include serial configuration ports, test and measurement equipment, industrial controllers, barcode scanners, printers, and external data-acquisition modules. The 20-pin SSOP package supports compact surface-mount layouts, while the combination of 3.0V minimum supply, 250kbps throughput, and 15kV ESD protection makes the device appropriate for short-distance point-to-point links where logic-level UART signaling must cross an RS-232 cable. Pay attention to charge-pump capacitor placement and signal routing during PCB layout. Keep the charge-pump capacitors close to their associated pins, provide an uninterrupted ground reference beneath the interface, and route driver outputs and receiver inputs away from noisy switching nodes. These measures preserve signal integrity and reduce the chance that charge-pump switching activity will disturb adjacent circuitry. This product page combines the manufacturer interface specifications, package information, pricing availability, and practical RS-232 design guidance. It also distinguishes confirmed drop-in alternatives from functionally similar devices that require pinout, package, and operating-limit verification before substitution.

詢價 聯絡我們
MAX3385ECAP-T - 250kbps RS-232 IC | Analog Devices
MAX3385ECAP-T

MAX3385ECAP-T - 250kbps RS-232 IC | Analog Devices

Analog Devices MAX3385ECAP-T is a low-power, true RS-232 transceiver IC rated for data rates up to 250kbps and operating from a 3.0V to 5.5V supply. The device provides two drivers and three receivers in a 20-pin SSOP package and includes protection for exposed RS-232 lines rated to 15kV ESD. Its combination of multi-driver and multi-receiver channels suits equipment that exchanges data across several serial interfaces. A true RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into digital logic levels. The MAX3385ECAP-T belongs to the RS-232 transceiver family within interface ICs, where it sits between a host controller or data-processing system and a cable-based peripheral. Unlike a single-direction line driver or receiver, the integrated transceiver supports both transmission and reception while limiting the number of external interface components. The MAX3385ECAP-T supports supply voltages from 3.0V to 5.5V, making it suitable for systems that operate from either 3.3V or 5V logic rails. Its stated maximum signaling rate is 250kbps, which provides sufficient bandwidth for common point-to-point control, instrumentation, industrial, and data-acquisition links. The integrated 15kV ESD protection is a principal feature for interfaces connected to external cables, where electrostatic discharge can enter through a connector and damage an unprotected transceiver. This device is identified as a 2/3 transceiver, meaning that two driver channels and three receiver channels are available for asymmetric RS-232 links. The manufacturer datasheet describes the MAX3385ECAP as a low-power true RS-232 transceiver for 3.0V to 5.5V operation. Its SSOP-20 package provides a compact surface-mount format, while the -T ordering suffix identifies the tape-and-reel shipping form associated with this exact manufacturer part number. Typical uses include industrial control links, test and measurement equipment, data-logging systems, point-of-sale equipment, and embedded serial interfaces. The combination of a 250kbps data rate and multiple receiver channels is particularly useful where one controller must monitor several incoming RS-232 signals while transmitting command or status data through another channel. External charge-pump capacitors and connector protection arrangements should follow the pin-description and typical-application diagrams in the manufacturer datasheet. Designers should verify that the system ground and signal-return arrangement satisfy the RS-232 interface requirements before placing the IC. The maximum cable length and achievable rate depend on the complete transceiver circuit, cable impedance, connector, noise environment, and system baud rate; the 250kbps figure is the device rating rather than a guarantee for every installed link. Decoupling and charge-pump routing should follow the recommended layout because switching-regulator and charge-pump currents can couple into sensitive signal paths. This product page consolidates the exact MAX3385ECAP-T electrical ratings, package information, interface characteristics, sourcing path, and engineering guidance into one reference. It also distinguishes confirmed pin-compatible replacements from merely similar RS-232 transceivers, helping designers avoid assuming that equivalent protocol functions guarantee PCB-level drop-in compatibility.

詢價 聯絡我們
MAX3385ECWN - 250kbps True RS-232 Transceiver | Analog Devices
MAX3385ECWN

MAX3385ECWN - 250kbps True RS-232 Transceiver | Analog Devices

Analog Devices MAX3385ECWN is a true RS-232 transceiver IC supporting a 3.0V to 5.5V supply, data rates up to 250kbps, and ESD protection rated at ±15kV. The device is offered in an 18-SOIC package and provides two drivers and three receivers, making it suitable for bidirectional and multi-channel serial-interface equipment. A true RS-232 transceiver is an interface IC that converts logic-level signals to RS-232 levels and converts incoming RS-232 signals back to logic levels. RS-232 is a point-to-point, unbalanced serial-interface standard widely used for industrial control, data acquisition, instrumentation, and legacy peripheral connections. Its transmitter and receiver circuitry provide the voltage conversion and noise tolerance required when logic levels must communicate with a longer, unbalanced cable. The MAX3385ECWN supports operation from a single 3.0V to 5.5V supply, allowing use in both 3.3V and 5V systems. Its maximum data rate of 250kbps is suitable for moderate-speed serial links, and the ±15kV ESD rating adds protection for exposed connector pins. The 2/3 driver-receiver configuration is useful when a design requires more receiver channels than transmitter channels. The MAX3385ECWN family uses integrated true RS-232 line-driver and line-receiver stages rather than a limited-voltage-only interface. This distinction is important when connecting to equipment that expects RS-232 voltage levels. Its operating-temperature range is specified as 0°C to 70°C for the commercial-grade CWN configuration, making it appropriate for equipment intended for controlled indoor or industrial environments within that range. Typical uses include industrial serial adapters, programmable-logic-controller communication, test and measurement instruments, barcode and data-acquisition equipment, and embedded control systems that retain an RS-232 port. Systems operating at 250kbps should include appropriate cable routing and grounding because unbalanced RS-232 performance can still be affected by ground offsets, electromagnetic interference, and connector cable characteristics. PCB implementation should follow the manufacturer's pin and decoupling guidance, particularly for supply connections and exposed RS-232 pins. Place the required bypass capacitor close to the device, route transceiver outputs to the connector through a short and appropriately arranged path, and confirm that system grounding satisfies the interface requirements before enabling communication. This page combines the manufacturer-oriented device identity, verified distributor descriptions, RS-232 design guidance, package details, and replacement analysis. It also identifies where additional electrical, mechanical, and lifecycle information must be confirmed in the manufacturer datasheet or through a current manufacturer quotation.

詢價 聯絡我們
MAX3385EEAP - 250kbps RS-232 Transceiver | Analog Devices
MAX3385EEAP

MAX3385EEAP - 250kbps RS-232 Transceiver | Analog Devices

The Analog Devices MAX3385EEAP is a low-power RS-232 transceiver rated for data rates up to 250kbps and operation from a 3.0V to 5.5V supply. The device is offered in a 20-pin SSOP package and provides the driver and receiver functions required to connect a modern digital circuit to an RS-232 serial port. Its integrated protection is specified for ±15kV electrostatic-discharge exposure on the serial lines. An RS-232 transceiver is an interface IC that belongs to the line-driver and line-receiver hierarchy within interface semiconductors. It converts logic-level signals into RS-232-compatible levels in the transmit direction and converts incoming RS-232 levels back into logic levels in the receive direction. The MAX3385EEAP therefore provides the physical signaling layer between equipment logic and a cable-based serial interface. Key characteristics include support for both 3.0V and 5.5V supply operation, a maximum signaling rate of 250kbps, low-power design, true RS-232 transceiver operation, and ±15kV ESD protection. The 3.0V minimum supply makes the interface suitable for systems whose digital core operates below 5V, while the 5.5V upper limit allows use with conventional 5V equipment. The 250kbps rate supports modern point-to-point serial links without requiring the lower bandwidth associated with legacy communication standards. The MAX3385EEAP combines two transmit drivers and two receive receivers in one package, matching the conventional direction and signal arrangement used by RS-232 interface designs. Its integrated ESD protection reduces the amount of external protection normally required at a connector or cable entry. Applications still require correct signal routing, suitable bypass capacitance, controlled return paths, and compliance with the applicable RS-232 electrical requirements. Typical uses include industrial control consoles, test equipment, data acquisition systems, service interfaces, and embedded products that retain an RS-232 port for configuration or diagnostics. The part is particularly useful where modern 3.3V logic must communicate with an RS-232 host while board area and external protection components must be minimized. Designers should begin with the manufacturer's pin-description table when assigning PCB tracks and must preserve the documented charge-pump and driver topology around the transceiver. Input and supply bypassing should be placed close to the relevant pins, and connector-side protection must be reviewed against the required ESD exposure and working voltage. This page consolidates the core electrical and package characteristics of the MAX3385EEAP with application guidance, comparison parameters, and practical interface-design considerations. It is intended to help engineers determine whether the device's voltage range, data rate, package, and protection level match a particular RS-232 design before committing the footprint to a PCB.

詢價 聯絡我們
MAX3386ECDW - 3/2 RS-232 Transceiver, 250kbps | Texas Instruments
MAX3386ECDW

MAX3386ECDW - 3/2 RS-232 Transceiver, 250kbps | Texas Instruments

The Texas Instruments MAX3386ECDW is a full-duplex RS-232 transceiver with three drivers and two receivers, a maximum data rate of 250kbps, and a 3V to 5.5V supply range in a 20-pin SOIC package. The device includes a split logic-side supply arrangement for mixed-signal systems. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by the RS-232 standard. It belongs to the communication transceiver family, which sits above line drivers and receivers in the interface hierarchy and ultimately supports serial data links in industrial, commercial, and embedded equipment. Key electrical features include 500mV receiver hysteresis for improved noise immunity, 3V to 5.5V operation, and ±25kV ESD protection as identified for this device. The three-driver, two-receiver arrangement supports multiple outbound channels and two inbound channels within one package. Full-duplex operation allows simultaneous transmission and reception, while the split supply pins give the circuit designer independent control over the logic-side supply arrangement. The MAX3386ECDW operates from 0°C to 70°C and is specified for surface-mount assembly in a 20-SOIC package measuring 0.295 inches, or 7.50mm, wide. Its 250kbps signaling rate is suitable for configuration ports, instrumentation, point-of-sale equipment, and legacy industrial control links. The integrated protection reduces the need for separate surge-protection components on exposed serial lines. Typical applications include RS-232 ports for embedded controllers, test and measurement instruments, industrial diagnostic interfaces, and data acquisition systems. Because this part is obsolete, engineers should confirm availability, lifecycle status, and any manufacturer-approved migration path before releasing a new production design. When laying out the board, keep the logic-side connections short and route the RS-232 lines away from clocks, switching regulators, and high-current power paths. Verify the external charge-pump capacitor values against the manufacturer datasheet and treat the RS-232 pins as external-facing signal nodes during EMC and ESD reviews. This page consolidates device specifications, lifecycle information, pin-compatible alternatives, and design guidance for engineers evaluating the MAX3386ECDW against current RS-232 interface options.

詢價 聯絡我們
MAX3386ECDWG4 - RS-232 Transceiver | Texas Instruments
MAX3386ECDWG4

MAX3386ECDWG4 - RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3386ECDWG4 is a dual line RS-232 transceiver with a split supply pin for the logic side, designed for mixed-voltage serial-interface systems. It is packaged in a 20-pin SOIC (0.295 inch, 7.50 mm width) and is identified as a commercial-grade RS-232 interface IC. The device supports ESD protection on the RIN inputs and DOUT outputs, including ±15 kV human-body-model protection, and is also described as a 3 V and ±25 kV ESD RS-232 device. An RS-232 transceiver is a signal-interface semiconductor that combines line drivers and line receivers to connect a digital logic system to a serial port using RS-232 electrical levels. In the hierarchy of electronic components, it belongs to the interface-IC family, specifically the RS-232 line-driver and receiver category. The split logic-side supply feature allows the logic-side voltage to be selected for compatibility with systems using mixed supply levels, while the RS-232 side handles the higher voltage signaling required by the standard. The MAX3386ECDWG4 is designed for applications requiring bidirectional or multi-line RS-232 connectivity, protection for exposed serial lines, and operation in a compact SOIC-20 package. Its stated ESD capability is particularly useful when the connector or cable interface may be exposed to electrostatic discharge during insertion, removal, or industrial handling. The commercial temperature designation indicates its intended use in commercial equipment rather than an automotive-qualified environment. The MAX3386E family uses split supply pins to support operation in mixed-signal systems. The logic-side supply feature allows a system designer to interface the transceiver with a lower-voltage digital subsystem, while the RS-232-side supply arrangement supports the voltage requirements of the line interface. The device also includes driver and receiver channels suited to point-to-point serial links, instrumentation, control equipment, and data-acquisition equipment. Typical applications include RS-232 ports in industrial controllers, laboratory instruments, POS terminals, serial adapters, embedded control boards, and communications equipment. In an industrial controller, the transceiver can place a protected RS-232 interface between a logic-level UART and an external DB9 or terminal connector. In measurement equipment, it can provide the electrical conversion and line protection needed when connecting an instrument to a host computer. Protection requirements should still be checked against the connector and cable environment. When laying out the board, place the transceiver close to the RS-232 connector and route the protected RIN and DOUT lines directly to the relevant pins to minimize exposure to electrostatic discharge and external cable transients. Confirm logic-side and RS-232-side supply levels, supply decoupling, and the UART signal levels before finalizing the design. The SOIC-20 footprint also requires adequate spacing around the pins for reliable assembly and rework. This product page combines the manufacturer-family characteristics, package information, ESD descriptions, interface details, practical application guidance, and verified replacement information for engineers evaluating the MAX3386ECDWG4. It is intended to support board-level decision making, footprint planning, cross-reference work, and RS-232 interface design rather than serving as a substitute for the complete manufacturer datasheet.

詢價 聯絡我們