產品(46,000+)

MAX3243EIRHBRG4 - 500kbps RS-232 Transceiver | Texas Instruments
MAX3243EIRHBRG4

MAX3243EIRHBRG4 - 500kbps RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3243EIRHBRG4 is a 3 V to 5.5 V multichannel RS-232 line driver/receiver featuring three drivers, five receivers, a dual charge-pump circuit, and a 500kbps data rate. The device is packaged in a 32-pin VQFN (HVQCCN) package measuring 5 mm by 5 mm and is specified for an industrial temperature range of -40 °C to 85 °C. An RS-232 transceiver is an interface integrated circuit that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic levels. Within the interface hierarchy, the MAX3243E combines a line driver, line receiver, and charge-pump voltage converter to support the bipolar voltage swings required by TIA/EIA-232-F on systems powered from a single 3 V to 5.5 V supply. The MAX3243E family includes 3-to-5.5 V operation, a 500kbps maximum data rate, and enhanced electrostatic-discharge protection. According to the manufacturer product information, serial-port pins provide plus-or-minus 15kV HBM and IEC61000-4-2 air-gap discharge protection, plus plus-or-minus 8kV IEC61000-4-2 contact-discharge protection. These ratings are important when the interface connects to externally accessible equipment through an unprotected cable. Internally, the dual charge-pump circuit generates the positive and negative voltages used by the line drivers, allowing the device to operate from a single low-voltage supply without an external negative supply. Three line drivers and five line receivers support common RS-232 serial-port arrangements where more receive channels are useful for handshake, status, or control signals. The receiver architecture is intended for asynchronous communication-controller interfaces operating at rates up to 500kbps. Typical applications include industrial serial links, data-acquisition equipment, barcode and point-of-sale systems, test instrumentation, and embedded control systems. It is also suitable for equipment implementing RS-232 over cable runs where surge and electrostatic-discharge exposure is likely. System designers should still retain appropriate board-level grounding, cable routing, and chassis-protection practices because the IC ratings address specified ESD test conditions rather than every possible surge event. The primary design consideration is decoupling. Place the charge-pump capacitors and supply capacitors close to their designated pins, keep the exposed-pad thermal and electrical connection correctly implemented, and follow the manufacturer layout guidance. Confirm that the selected connector, cable, and system grounding strategy produce compatible RS-232 levels before releasing a production design. This page combines manufacturer specifications, package details, replacement guidance, comparison data, and practical implementation notes for faster engineering evaluation.

詢價 聯絡我們
MAX3243EUI+ - 3.3V/5V RS-232 Transceiver | Analog Devices
MAX3243EUI+

MAX3243EUI+ - 3.3V/5V RS-232 Transceiver | Analog Devices

Analog Devices MAX3243EUI+ is a +3V to +5.5V RS-232 transceiver with three drivers and three receivers, automatic shutdown and wake-up, full-duplex operation, and enhanced electrostatic-discharge protection in a 28-pin TSSOP package. According to the manufacturer product page, the MAX3243 family is in production and supports both 3V and 5V supply operation. An RS-232 transceiver is a serial-interface integrated circuit that converts between TTL/CMOS logic levels and the voltage-defined RS-232 signal levels used by computer serial ports and industrial equipment. The MAX3243EUI+ belongs to the interface-IC hierarchy: RS-232 transceiver → multi-channel serial-interface transceiver → communications interface IC → semiconductor. Automatic shutdown provides a practical power-management advantage when no valid receiver activity is detected. Key features include a 3V to 5.5V supply range, three transmit channels, three receive channels, AutoShutdown operation, enhanced ESD protection, and a 28-pin TSSOP package. The MAX3243E family description identifies EIA/TIA-232 and V.28/V.24 support, automatic shutdown and wake-up behavior, high data-rate capability, and enhanced electrostatic-discharge protection. These characteristics suit systems that must translate between modern digital logic and legacy RS-232 ports. The MAX3243EUI+ integrates both interface directions on one device, reducing the component count required for a multi-channel serial port. Its automatic shutdown function can reduce power consumption when the remote system is disconnected or inactive. The 28-pin TSSOP is a surface-mount package that supports conventional PCB assembly, although exact pin assignments, capacitor values, and electrical limits must be confirmed from the manufacturer datasheet before layout or replacement qualification. Typical uses include industrial control equipment, data-acquisition systems, configuration ports, service interfaces, and embedded systems that need to communicate with RS-232 peripherals. It is also appropriate for battery-powered or portable equipment where automatic shutdown can conserve energy during idle periods. In those applications, logic-level compatibility, ESD protection, and cable-receiver behavior are as important as the nominal data rate. When designing around the MAX3243EUI+, verify the complete supply range, operating temperature, absolute maximum ratings, driver slew rate, receiver thresholds, and required external charge-pump capacitors against the manufacturer datasheet. Place the interface IC close to the connector, route driver outputs toward the protected connector side, and provide a low-impedance ground return so common-mode noise does not corrupt receiver inputs. This page consolidates verified manufacturer and distributor information with practical selection guidance, parameter comparisons, and engineering-oriented interface design notes. It also distinguishes verified drop-in candidates from unresolved alternatives, helping engineers reduce sourcing risk while retaining the required 28-pin TSSOP footprint.

詢價 聯絡我們
MAX3243EUI+T - 3/5 RS-232 Transceiver, 250kbps | Maxim
MAX3243EUI+T

MAX3243EUI+T - 3/5 RS-232 Transceiver, 250kbps | Maxim

The Maxim Integrated MAX3243EUI+T is a 3-driver/5-receiver, full-duplex RS-232 transceiver designed for 3 V to 5.5 V operation. It supports data rates up to 250 kbps and provides ±15 kV ESD protection in a 28-pin TSSOP package. The MAX3243EUI+T also includes Maxim's AutoShutdown feature, which disables the internal charge pump and driver circuitry when the receiver inputs do not detect a valid signal level. An RS-232 transceiver is an interface IC that translates between logic-level signals and the bipolar voltage levels used by RS-232 links. The MAX3243 belongs to the RS-232 transceiver class within interface ICs, where it combines drivers, receivers, an on-board charge pump, and low-power shutdown control. This integration reduces the number of external components required for portable equipment, industrial controllers, and computer peripherals. Key features include three RS-232 drivers, five RS-232 receivers, full-duplex operation, a 3 V to 5.5 V supply range, operation at up to 250 kbps, and ±15 kV ESD protection. AutoShutdown is particularly useful in battery-powered equipment because the device can reduce supply consumption when no valid receiver signal is present. A complementary always-active receiver supports continuous monitoring in designs that cannot tolerate shutdown of every receiver path. The MAX3243 family combines an on-board power supply with RS-232 line-driver and receiver functions. Maxim's AutoShutdown circuitry detects whether a valid signal is present on the receiver inputs and shuts down the onboard supply and drivers when appropriate. The MAX3243EUI+T therefore supports both energy-efficient intermittent communication and always-active monitoring within one interface device. Typical uses include battery-powered instruments, point-of-sale equipment, industrial data-acquisition systems, printers, portable computers, and external communications equipment. Its 28-pin TSSOP package is appropriate for compact industrial and embedded assemblies where three RS-232 outputs and five inputs are required. The interface is especially useful when a system must monitor several incoming lines while retaining the option to place unused drivers into a low-power state. When designing around the MAX3243EUI+T, place the charge-pump capacitor and receiver and driver interface components according to the manufacturer's recommended layout. Confirm that every connected RS-232 line is protected against electrostatic discharge and that the selected cable does not exceed the voltage and grounding requirements of the RS-232 interface. Firmware should also account for AutoShutdown behavior when a remote system may disconnect without first sending a valid signal. This product record combines the manufacturer specifications with package, application, comparison, and design guidance. It also separates exact catalog facts from electrical details that still require confirmation in the current Analog Devices or Maxim Integrated datasheet, helping engineers evaluate the MAX3243EUI+T for new RS-232 designs without confusing it with the faster MAX3243E or lower-speed MAX3243C variants.

詢價 聯絡我們
MAX3243EUU - 3V to 5.5V RS-232 Transceiver | Analog Devices
MAX3243EUU

MAX3243EUU - 3V to 5.5V RS-232 Transceiver | Analog Devices

The Analog Devices MAX3243EUU is a multichannel RS-232 line driver and receiver operating from a 3V to 5.5V supply, with data rates up to 250 kbps and integrated protection for RS-232 transceiver applications. The MAX3243 family is designed for portable equipment, data acquisition systems, industrial controls, and battery-powered instruments where low supply voltage, automatic shutdown, and compact serial-interface integration are important. An RS-232 transceiver is a bidirectional interface IC that converts logic-level UART signals into RS-232 line levels and converts received line-level signals back into CMOS-compatible digital signals. The MAX3243 combines multiple drivers and receivers with charge-pump circuitry for ±RS-232 voltage generation, reducing the external component count compared with discrete implementations. In the MAX3243EUU, this integration supports a low-voltage system architecture without requiring a separate 5V-only transceiver. Key electrical features include a 3V to 5.5V operating supply range, multichannel driver and receiver support, and operation up to 250 kbps. The Analog Devices product page identifies the MAX3243 as a production device with AutoShutdown capability, while the TI product listing describes the family as a 3V to 5.5V multichannel 250 kbps RS-232 line driver and receiver with plus-or-minus 15 kV ESD protection. The MAX3243EUU is supplied in a 28-pin small-outline package identified by distributor listings as TSSOP-28. It is appropriate for UART bridges, USB-to-serial adapters, embedded control boards, test equipment, and industrial serial controllers. Its low-voltage operation allows direct use with 3.3V microcontrollers, provided the logic levels and supply arrangement are verified against the device data sheet. Designers should confirm the exact package pinout, exposed-pad requirements, charge-pump capacitor values, and RS-232 line-driver loading limits before layout release. Decoupling capacitors should be placed close to the supply and ground pins, while the auto-shutdown and enable functions should be checked for compatibility with the host system's power-management sequence. This page combines the verified manufacturer and distributor references, pricing information available as of 2026-10-30, package information, and practical design guidance for engineers evaluating the MAX3243EUU in low-voltage serial-interface designs.

詢價 聯絡我們
MAX3243IDB - 3/5 RS-232 Transceiver | Texas Instruments
MAX3243IDB

MAX3243IDB - 3/5 RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243IDB is a 3-driver, 5-receiver RS-232 transceiver operating from 3 V to 5.5 V at up to 250 kbps, with ±15 kV HBM ESD protection in a 28-pin SSOP (DB) package. The industrial-temperature grade supports operation from -40°C to +85°C. An RS-232 transceiver is an interface IC that combines differential line drivers and receivers for point-to-point serial data links. The MAX3243 belongs to the RS-232 interface transceiver family within interface ICs and broader semiconductor signal-processing devices. It translates logic-level signals between a host or controller and external RS-232 equipment, while its driver channels strengthen signals for reliable cable transmission. Key features include three driver channels, five receiver channels, operation across a 3 V to 5.5 V supply range, and 250 kbps data-rate capability. The ±15 kV human-body-model ESD protection helps improve connector and cable-interface ruggedness. The AutoShutdown feature can reduce supply current to 1 µA when the circuit does not detect a valid signal level, making the device useful in power-conscious embedded systems. The MAX3243 uses CMOS-compatible logic interfacing to manage three RS-232 transmit channels and five receive channels. A 28-pin SSOP provides a compact surface-mount footprint, while the -40°C to +85°C rating supports industrial equipment. Its combination of multiple channels, low-voltage operation, and automatic shutdown makes it suitable for systems that require more than a single RS-232 port. Typical applications include industrial serial-port adapters, USB-to-RS-232 interface equipment, data-acquisition controllers, point-of-sale terminals, instrumentation, and embedded systems that exchange command or telemetry data over RS-232 cables. Multiple drivers and receivers also allow one controller to connect to several peripherals when the cable lengths and data rates suit RS-232 operation. PCB implementation requires careful treatment of RS-232 as a differential, bipolar interface rather than a logic-level net. Place the transceiver close to the connector, maintain the intended ground path, and apply the protection and bypass components recommended by the manufacturer. The AutoShutdown circuit may also require correct external capacitor selection for the intended startup behavior. This product record consolidates the key electrical ratings, package details, lifecycle information, cross-reference candidates, and practical design guidance needed to evaluate the MAX3243IDB and plan a replacement before committing to a new PCB layout.

詢價 聯絡我們
MAX3243IDBG4 - 3/5 RS-232 Transceiver | Texas Instruments
MAX3243IDBG4

MAX3243IDBG4 - 3/5 RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243IDBG4 is a 3-driver and 5-receiver RS-232 transceiver designed for 3 V to 5.5 V operation. It supports RS-232 and CMOS interfacing, provides ±15 kV human-body-model ESD protection, and is packaged in a 28-pin SSOP with a 5.30 mm body width. The device is intended for industrial-temperature RS-232 links operating from 0°C to 70°C. An RS-232 transceiver is an interface IC that converts between CMOS logic levels and balanced, single-ended RS-232 signals. It combines line drivers, receivers, and charge-pump support circuitry into one package. Within the interface hierarchy, the MAX3243IDBG4 belongs to the RS-232 transceiver class, connecting low-voltage digital controllers to external serial ports through the EIA RS-232 electrical standard. Key features include three RS-232 drivers, five RS-232 receivers, a 3 V to 5.5 V supply range, and ±15 kV HBM ESD protection. The MAX3243 family also includes AutoShutdown functionality, allowing very low supply current when no valid signal is detected. These characteristics suit equipment requiring multiple serial channels, such as industrial controllers, test systems, point-of-sale equipment, and legacy peripheral interfaces. The device uses Maxim's low-power RS-232 interface approach and operates from both 3.3 V and 5 V system rails. The MAX3243IDBG4 industrial suffix identifies the specified temperature range, while the DBG package code identifies the 28-pin SSOP configuration. Its multi-channel arrangement allows one logic device to connect multiple external RS-232 ports while limiting the number of separate transceiver packages required on the PCB. Typical applications include industrial serial-port expansion, programmable logic controller communications, laboratory data-acquisition equipment, point-of-sale systems, and embedded systems that need to communicate with legacy RS-232 peripherals. The three-driver arrangement is useful when several external devices must receive commands, while the five receivers allow multiple incoming serial signals to be monitored simultaneously. PCB design should preserve the capacitance limits and connection details required by the RS-232 interface while providing suitable decoupling close to the supply pins. Cable-side protection must also account for electrostatic discharge; the IC's ±15 kV HBM rating protects the device pins when used in the application configuration described by the manufacturer, but it does not replace correct grounding, shielding, or cable design. This product page combines the exact ordering information, electrical characteristics, package details, interface role, application guidance, and verified substitution constraints for the MAX3243IDBG4. It also distinguishes genuine same-footprint drop-in choices from cross-package or merely functional equivalents, helping engineers avoid a PCB redesign when replacing the device.

詢價 聯絡我們
MAX3243IDBR - 3.3V 5V 250kbps RS-232 Transceiver | Texas Instruments
MAX3243IDBR

MAX3243IDBR - 3.3V 5V 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243IDBR is a 3. to 5.5-V multichannel RS-232 line driver and receiver with 250 kbps data rate and ±15-kV ESD protection, housed in a 28-pin SSOP (DB) package. The device integrates three RS-232 drivers and five receivers, providing a compact interface for low-speed serial data, industrial-control links, and equipment communication. An RS-232 transceiver is an interface IC that combines voltage-line drivers and receivers for serial communication using the RS-232 standard. It belongs to the broader categories of communication interface ICs, interface transceivers, and data-conversion semiconductors. The MAX3243IDBR is intended for systems that need multiple serial channels without allocating a separate driver or receiver for every line. The 3.0-V to 5.5-V supply range supports both 3.3-V and 5-V system rails, while the 250-kbps signaling rate covers common control, configuration, and point-to-point communication links. The integrated ±15-kV human-body-model ESD protection improves tolerance to electrostatic discharge at externally accessible connector pins. The industrial temperature option is specified for operation from -40°C to +85°C. The 28-pin SSOP package is useful for compact board layouts where a higher pin-count RS-232 interface is needed. Its pin arrangement must be matched against the manufacturer datasheet when assigning driver outputs, receiver inputs, supply, ground, and enable-related functions. The MAX3243 family also includes related product variants, so designers should verify the exact ordering code when using a substitute. Typical applications include industrial serial adapters, programmable logic controllers, test equipment, barcode scanners, and embedded control boards. In a PLC or embedded controller, the three drivers can send commands to external modules while five receivers monitor incoming status lines. The 250-kbps rate is more appropriate for control and instrumentation traffic than for high-speed storage transfers. For a new layout, place protection and bypass components close to the device and route exposed RS-232 traces away from sensitive analog and clock nodes. Confirm that the selected connector, cable, and ground strategy are appropriate for the intended RS-232 environment. This page combines the manufacturer specifications, package information, sourcing workflow, replacement guidance, and practical design considerations for faster component selection.

詢價 聯絡我們
MAX3243IDW - 250kbps 3/5 RS-232 Transceiver | Texas Instruments
MAX3243IDW

MAX3243IDW - 250kbps 3/5 RS-232 Transceiver | Texas Instruments

Texas Instruments MAX3243IDW is a 3- to 5.5-V multichannel RS-232 line driver and receiver capable of operation up to 250 kbps, with ±15 kV Human Body Model ESD protection on bus pins. The device integrates three drivers and five receivers in a 28-pin DW SOIC package, making it suitable for multichannel serial-interface equipment. An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and the bipolar voltage levels used by RS-232 equipment. It combines drivers, receivers, and often charge-pump voltage-generation circuitry into one package. This integrated approach reduces external component count and helps designers implement PC serial ports, industrial controls, data-collection equipment, and other systems that require reliable serial communication over longer cable runs. The MAX3243IDW operates from a 3 V to 5.5 V supply, allowing use in both 3.3 V and 5 V systems. Its 250 kbps signaling rate supports legacy serial-port data rates and other multichannel RS-232 links. Individual channel enable and shutdown functions provide control over transmitter and receiver activity, while AutoShutdown operation reduces supply current when no valid signal is present. The integrated charge pump supports standard RS-232 voltage generation without an external DC-DC converter. Electrical protection is a significant feature for connector-facing circuits. The MAX3243 provides ±15 kV ESD protection using the Human Body Model on RS-232 bus pins. Protection does not replace proper connector design, external surge protection, or controlled cable routing, but it adds a useful barrier against electrostatic discharge encountered during handling and field installation. Typical applications include DE-9 serial-port interfaces, industrial data acquisition, point-of-sale equipment, test and measurement systems, and embedded control systems that exchange commands or diagnostic data with RS-232 peripherals. The three-driver and five-receiver arrangement is especially useful when one controller must communicate with multiple external devices while maintaining independent transmit control. Design should account for charge-pump capacitor selection, local bypassing, unused-channel configuration, and the voltage-versus-current behavior of RS-232 drivers. Keep ground and signal routing consistent with the referenced design, place bypass and charge-pump components close to the device, and validate cable length and data rate together because both influence signal integrity and receiver margin. This product page combines the manufacturer's electrical and package information with practical interface guidance, application scenarios, parameter-level comparisons, and replacement criteria. It is intended to help engineers determine whether the MAX3243IDW meets voltage, channel-count, data-rate, ESD, package, and lifecycle requirements before committing it to an RS-232 design.

詢價 聯絡我們
MAX3243IDWRG4 - 3.3V/5V RS-232 IC | Texas Instruments
MAX3243IDWRG4

MAX3243IDWRG4 - 3.3V/5V RS-232 IC | Texas Instruments

The Texas Instruments MAX3243IDWRG4 is a multichannel RS-232 line driver and receiver with a 3 V to 5.5 V supply range, three driver channels, five receiver channels, and ±15 kV ESD protection in a 28-pin SOIC package. It combines bidirectional RS-232 interface capability with CMOS-compatible logic and low-power shutdown behavior for industrial equipment, data acquisition systems, and service-port designs. An RS-232 transceiver is an interface IC that converts logic-level signals between a host or controller and equipment using the RS-232 standard. A line driver translates host-side digital signals into RS-232 levels, while a receiver converts the bipolar serial signal back into a digital level. Within the interface hierarchy, the MAX3243IDWRG4 belongs to the RS-232 transceiver class of multi-channel interface ICs used to bridge TTL, CMOS, and serial equipment. The device operates from 3 V to 5.5 V, allowing use with both 3.3 V and 5 V systems. It provides three RS-232 drivers and five receivers, making it useful for designs with several communication ports or more receive inputs than transmit outputs. Its ±15 kV human-body-model ESD protection improves robustness at externally accessible connector pins, while its 1 µA shutdown supply current supports power-conscious systems that disable the interface when it is not needed. The MAX3243 family combines charge-pump voltage generation and CMOS driver and receiver circuitry in one device. Charge-pump circuitry develops the RS-232 level-shift voltage required when the supply cannot directly generate the required output swing. This integrated approach reduces the number of external components compared with discrete RS-232 interface networks and simplifies connections among logic-level controllers and remote serial equipment. Typical uses include industrial control equipment, instrumentation, data loggers, POS terminals, and computer peripheral connections. The five receiver channels can monitor multiple incoming lines, while the three drivers support outbound RS-232 channels. Systems using the shutdown function can reduce supply consumption when the interface is inactive, although power-management timing must be coordinated with the host controller. PCB layout should follow the capacitor and charge-pump recommendations in the manufacturer datasheet, particularly regarding input and output bypassing capacitors and placement near the device. Keep the RS-232 connector side physically separated from sensitive logic or analog circuitry where practical, and route high-energy external lines away from low-level signal traces to reduce ESD and surge-related coupling. This product page combines electrical characteristics, interface-use guidance, package details, and design considerations to support faster component selection. It also distinguishes verified pin-compatible replacement options from alternatives that require a different footprint, helping engineers evaluate a MAX3243IDWRG4 redesign before committing to a PCB change.

詢價 聯絡我們
MAX3243IPW - 250kbps RS-232 Transceiver | Texas Instruments
MAX3243IPW

MAX3243IPW - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243IPW is a 3- to 5.5-V multichannel RS-232 line driver and receiver rated for data rates up to 250 kbps, with three drivers and five receivers in a 28-pin TSSOP package. The device is designed for serial-port and other point-to-point RS-232 interfaces where several channels must share one low-voltage supply. An RS-232 transceiver is an interface IC that combines the electrical functions required to communicate between TTL or CMOS logic and RS-232 logic levels. Within the interface hierarchy, the MAX3243IPW is a multichannel RS-232 transceiver, also described as a line driver and receiver. Its driver channels convert logic-level inputs into RS-232-compatible signals, while its receiver channels convert incoming RS-232 signals into logic-level outputs. The MAX3243IPW operates from 3 V to 5.5 V, supports signaling up to 250 kbps, and includes ±15-kV ESD protection using the HBM test method on the serial-port connection pins. Three drivers and five receivers provide an asymmetric channel count suited to applications such as DE-9 serial connections. The manufacturer also describes AutoShutdown functionality and always-enabled ROUT2B and INVALID outputs for monitoring ring and valid-input status. The wider supply range allows the interface to operate from 3.3-V or 5-V system rails without a separate RS-232 transceiver supply. Multiple integrated drivers and receivers reduce the number of external interface ICs required in multi-channel equipment. Always-enabled status outputs can simplify supervision of modem or communications equipment, although their fixed operation should be checked against the system power-management architecture. Typical uses include legacy RS-232 serial ports, industrial control interfaces, data-acquisition equipment, point-of-sale terminals, and embedded systems requiring legacy peripheral connectivity. The MAX3243IPW can also complement a modern microcontroller or transceiver module when an existing enclosure or cable standard still exposes RS-232 signals. Careful signal-level, grounding, and ESD layout practices remain necessary in electrically noisy environments. For PCB design, place the device near the connector or protected interface entry point and route protected RS-232 traces away from sensitive analog and clock circuitry. Confirm that the exposed connector pins have appropriate surge and ESD protection because the integrated ±15-kV HBM rating does not eliminate the need for an engineered external protection strategy. Follow the manufacturer pin-description and layout guidance for decoupling, grounding, and protection-network placement. This product reference combines the MAX3243IPW electrical identity, verified package information, channel configuration, interface capabilities, and application-oriented engineering guidance. It also provides a framework for checking pin-compatible alternatives, understanding the limits of interface protection, and selecting between integrated transceivers, system transceivers, and newer communication architectures.

詢價 聯絡我們
MAX3243IPWRE4 - 3.3V 250kbps RS-232 | Texas Instruments
MAX3243IPWRE4

MAX3243IPWRE4 - 3.3V 250kbps RS-232 | Texas Instruments

Texas Instruments MAX3243IPWRE4 is a multichannel RS-232 line driver and receiver operating from 3 V to 5.5 V, supporting data rates up to 250 kbps and ±15 kV human-body-model ESD protection in a 28-pin TSSOP package. The device provides three drivers and five receivers, making it suitable for compact industrial, embedded, and communications equipment requiring a single-level RS-232 interface. An RS-232 transceiver is an interface IC that converts between single-ended digital logic signals and the voltage levels used by the RS-232 standard. It belongs to the hierarchy of interface ICs, communication interfaces, serial-interface transceivers, and semiconductors. Each driver converts logic-level inputs into RS-232 outputs, while each receiver converts differential noise-resistant inputs into logic-level outputs. This bidirectional conversion supports point-to-point serial links between equipment, controllers, test systems, and peripheral modules. The MAX3243 family operates across a 3 V to 5.5 V supply range, allowing operation from both 3.3 V and 5 V systems. Its maximum signaling rate of 250 kbps suits control links, industrial equipment, instrumentation, and legacy serial connectivity. Three driver channels and five receiver channels provide more receive capacity than transmit capacity, allowing several incoming RS-232 signals to be monitored while supporting three outbound connections. The ±15 kV HBM ESD rating adds board-level protection for exposed serial ports. The E4 ordering suffix identifies the lead-free 28-pin TSSOP configuration shown in the product ordering information. This surface-mount package supports automated assembly while requiring careful layout around the RS-232 connector and supply rails. The device is not a modern differential serial transceiver: it is intended for point-to-point RS-232 signaling rather than RS-485 multidrop networks, USB, or differential Ethernet interfaces. Its design includes the voltage levels, slew behavior, and receiver thresholds associated with RS-232. Typical applications include industrial control panels, barcode and labeling equipment, security and access-control systems, serial-to-embedded-controller links, test instrumentation, and point-to-point service interfaces. A design can pair the MAX3243 with a microcontroller UART for logic-side connections while using a DE/RE-style control strategy where driver outputs are intentionally disabled. The receiver count also supports monitoring several incoming alarm, status, or sensor signals through separate RS-232 sources. For reliable implementation, place the transceiver close to the connector, keep RS-232 traces short and away from clocks or switching nodes, and provide the decoupling and protection required by the application. Decoupling capacitors should be placed adjacent to the supply and ground pins. External protection may still be needed for exposed cables because the on-chip ±15 kV HBM rating is a device-level specification rather than a guarantee of complete connector immunity. This page combines manufacturer specifications, drop-in substitution guidance, application-focused engineering notes, and a parameter comparison organized for PCB designers and component engineers evaluating the MAX3243IPWRE4 for 3.3 V or 5 V RS-232 designs.

詢價 聯絡我們
MAX3243IPWRG4 - 250kbps RS-232 Transceiver | Texas Instruments
MAX3243IPWRG4

MAX3243IPWRG4 - 250kbps RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243IPWRG4 is a 3-to-5.5 V multichannel RS-232 line driver and receiver rated for data rates up to 250 kbps, with plus or minus 15 kV human-body-model ESD protection in a 28-pin TSSOP package. The device integrates three RS-232 drivers and three receivers with AutoShutdown capability, allowing the supply current to fall to 1 uA when no valid signal is detected. An RS-232 transceiver is an interface IC that converts between single-ended, bipolar logic-level signals used by host systems and the differential voltage signaling required by RS-232 equipment. Within the interface hierarchy, the MAX3243 combines a line driver, line receiver, voltage-level translation, and electrostatic-discharge protection into one low-voltage CMOS device. This integration reduces board area and component count while maintaining compatibility with powered-down portable and industrial equipment. The MAX3243IPWRG4 operates from 3 V to 5.5 V, making it suitable for systems using either 3.3 V or 5 V power rails. Its 250 kbps maximum data rate supports standard serial links used for instrumentation, industrial control, point-of-sale equipment, and data acquisition. The 28-pin TSSOP package has a stated 0.65 mm terminal pitch and 5.30 mm body width, enabling compact surface-mount layouts where a larger package would be inconvenient. AutoShutdown provides an important power-management advantage for portable and intermittently connected systems. When the receiver detects no valid RS-232 signal, the device can enter a shutdown state and reduce supply current to 1 uA. Resume timing and capacitor sizing should still be evaluated against the system communication protocol, particularly when the remote transmitter can remain connected but idle for long periods. Typical uses include industrial serial controllers, laboratory interfaces, barcode scanners, security equipment, and embedded service ports. The three-driver, three-receiver arrangement works well for compact dual-ended links, while the protected low-voltage interface suits systems that need reliable translation between CMOS logic and RS-232 levels. Designers should account for the voltage levels and grounding requirements of the connected RS-232 equipment when evaluating signal integrity. Place the device close to the connector and use short, appropriately terminated signal routes for the highest practical noise immunity. Follow the manufacturer datasheet for external charge-pump capacitors, driver output wiring, receiver input handling, and ESD layout. Verify that the power rail, logic levels, line-direction control, and operating temperature meet the complete system requirements before releasing the PCB. This product record combines electrical specifications, package details, pin-location guidance, application fit, and qualified drop-in comparison information. It also highlights practical power-management and layout considerations so engineers can assess the MAX3243IPWRG4 against other RS-232 interface choices before committing to a board design.

詢價 聯絡我們
MAX3243MDBREP - 3V/5.5V 250kbps RS-232 Transceiver | TI
MAX3243MDBREP

MAX3243MDBREP - 3V/5.5V 250kbps RS-232 Transceiver | TI

Texas Instruments MAX3243MDBREP is a 3 V to 5.5 V multichannel RS-232 line driver and receiver operating at up to 250 kbps, with ±15 kV human-body-model ESD protection and a 28-pin SSOP package. The device provides three line drivers, five line receivers, and a dual charge-pump circuit for generating the bipolar voltages required by RS-232 line drivers. An RS-232 transceiver is an interface IC that converts logic-level signals from a host, controller, or peripheral into RS-232-compatible line levels and converts received line-level signals back into digital logic. The MAX3243 belongs to the interface IC, communications transceiver, and RS-232 line-driver/receiver hierarchy. Its multichannel arrangement supports equipment that requires several data lines but not a full nine-line desktop serial port. The MAX3243 operates from a single 3 V to 5.5 V supply, allowing operation from 3.3 V and 5 V systems. Its 250 kbps data rate is suitable for asynchronous serial links whose required baud rate remains below that operating limit. Pin-to-pin ESD protection of ±15 kV applies to the serial-port connection pins, including ground, according to the Texas Instruments MAX3243 datasheet. Internally, the MAX3243 combines three drivers, five receivers, and a dual charge-pump circuit. The charge pump generates the positive and negative voltage rails needed by the line drivers while allowing operation from a low-voltage single supply. The interface meets the electrical requirements of TIA/EIA-232-F and is intended to sit between an asynchronous communication controller and a serial-port connector. Typical uses include industrial control equipment, instrumentation, data acquisition systems, point-of-sale terminals, and embedded serial interfaces. The three transmitters and five receivers make the device useful for designs combining several command, status, and data paths while keeping the external power supply simple. The enhanced-product ordering option is suited to applications requiring the military temperature range and enhanced environmental screening. Layout is critical because RS-232 driver outputs carry high-voltage transitions, while receiver inputs are sensitive to electrical noise. Keep charge-pump and receiver-capacitor connections short, provide a solid ground reference, and route serial traces away from clocks, switching nodes, and high-current return paths. Confirm that the selected external capacitors satisfy the datasheet recommendations and that connector-side protection is coordinated with the IC's ±15 kV HBM rating. This product guide combines the manufacturer's electrical specifications, ordering information, package details, and practical RS-232 design guidance. It also identifies the verified pin-compatible MAX3243IDBR option while clearly separating package, temperature, and qualification differences that must be reviewed before design substitution.

詢價 聯絡我們
MAX3243MPWREP - 3/5 RS-232 Transceiver | Texas Instruments
MAX3243MPWREP

MAX3243MPWREP - 3/5 RS-232 Transceiver | Texas Instruments

The Texas Instruments MAX3243MPWREP is a 3V-to-5.5V multichannel RS-232 line driver and receiver in a 28-pin TSSOP package. It integrates three line drivers, five line receivers, and a dual charge-pump circuit, providing the electrical interface between an asynchronous communication controller and a serial connector. The device supports data rates up to 250 kbps and includes ±15 kV human-body-model ESD protection on the serial-port connection pins. An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into digital logic levels. The MAX3243 belongs to the RS-232 transceiver family, within the broader interface IC and semiconductor hierarchy. Its integrated charge pumps generate the positive and negative voltages required by RS-232, reducing the need for external discrete supply circuitry. The principal features of the MAX3243MPWREP are its three-driver, five-receiver configuration, 3V-to-5.5V supply operation, and 250 kbps data-rate capability. The 3V minimum supply voltage supports integration with modern low-voltage digital controllers, while the 5.5V maximum accommodates conventional 5V systems. Pin-to-pin ±15 kV HBM ESD protection adds robustness at exposed serial connectors. The device includes a dual charge-pump circuit to support RS-232 signal levels from a single supply. Five receivers allow multiple incoming channels to be monitored, while three drivers support outbound RS-232 connections. The asymmetric channel count makes the device suitable for designs that require more receive capability than transmit capability, such as control, monitoring, or diagnostic equipment. Typical applications include industrial serial controllers, point-of-sale terminals, instrumentation, data-collection systems, and RS-232 port expansion. The 250 kbps maximum data rate is appropriate for asynchronous control links and moderate-rate data transfers. System designers must still account for cable length, connector exposure, signal integrity, and the electrical limitations of the RS-232 standard. Decoupling capacitors should be placed close to the charge-pump and supply pins, while external protection may be needed when cables extend beyond the enclosure or connect to electrically noisy equipment. Verify the pin configuration and capacitor values in the manufacturer datasheet before layout because the dual charge-pump topology depends on correct external capacitor placement. This page combines the MAX3243MPWREP electrical characteristics, drop-in replacement options, application guidance, and practical layout considerations to support faster component selection and board-level implementation. It also provides a concise comparison of channel count, voltage range, data rate, protection, package, and temperature coverage for engineering review.

詢價 聯絡我們
MAX3245ECAI+ - 1Mbps 3/5 RS-232 Transceiver | Analog Devices
MAX3245ECAI+

MAX3245ECAI+ - 1Mbps 3/5 RS-232 Transceiver | Analog Devices

The Analog Devices MAX3245ECAI+ is a 3.0V-to-5.5V, ±15kV ESD-protected RS-232 transceiver with three drivers, five receivers, 1Mbps data rate, 1uA shutdown current, and a 28-pin SSOP package. An RS-232 transceiver is an interface IC that converts between complementary logic-level signals and the voltage-defined bipolar signaling used by RS-232 equipment. It belongs to the transceiver class within interface ICs, bridging UART, microcomputer, industrial-control, and communications systems. The MAX3245 family supports EIA/TIA-232 and V.28/V.24 communication interfaces while reducing the number of external components needed for a practical RS-232 port. Three driver channels and five receiver channels support multi-drop or multi-peripheral point-to-point arrangements. Its 1Mbps maximum data rate is suitable for moderate-speed serial links, and the ±15kV ESD rating adds protection for exposed connector-facing circuitry. The 3.0V-to-5.5V supply range accommodates both 3.3V and 5V system rails. AutoShutdown Plus provides low-power behavior for systems where power consumption matters during idle periods. The MAX3245ECAI+ uses the MAX3245E device family and is identified with the E suffix, 28-pin SSOP package, and industrial-temperature ordering code in the supplied distributor data. The verified distributor listings describe the device as a full RS-232 transceiver with three drivers and five receivers. The exact internal channel pinout, electrical limits, charge-pump capacitor requirements, and package dimensions require confirmation from the manufacturer datasheet before layout or replacement approval. Typical uses include USB-to-RS-232 adapters, industrial serial consoles, instrumentation, data acquisition, embedded control boards, and service ports. In each case, the transceiver provides the physical-layer conversion while the attached UART or processor handles framing and protocol software. The 1uA shutdown specification can reduce standby current when the port is not actively used, provided the AutoShutdown Plus control and external network are configured correctly. For PCB design, place the device close to the RS-232 connector, route driver and receiver traces away from sensitive analog or high-speed digital signals, and verify the required external charge-pump capacitors against the datasheet. This page combines verified distributor specifications, source traceability, replacement analysis, and application guidance; it does not invent unprovided pin assignments or pricing values.

詢價 聯絡我們
MAX324CPA+ - Precision SPST Analog Switch | Maxim
MAX324CPA+

MAX324CPA+ - Precision SPST Analog Switch | Maxim

The Maxim Integrated MAX324CPA+ is a precision, single-supply, normally closed SPST analog switch with two independent channels, packaged in an 8-pin PDIP. It operates from 2.7 V to 16 V, supports 1:1 signal routing, and is specified with a 60 ohm on-resistance in the distributor listing for this exact device. An analog switch is an integrated semiconductor device that connects or discloses signal paths under digital control. The MAX324CPA+ belongs to the analog switch family within the broader interface IC category. Its normally closed configuration provides a defined signal path when the control input is inactive, making it useful for precision routing in test systems, communication equipment, audio and video circuits, and battery-powered instruments. Key features include two SPST channels, operation from a single 2.7 V to 16 V supply, and low power consumption of approximately 5 microwatts. The device is TTL compatible when operated from a single 5 V supply. Maxim identifies the MAX324 as a production part, and the MAX324CPA+ is offered in a commercial temperature grade in an 8-pin through-hole PDIP package. The switch architecture is designed for low-power single-supply operation rather than high-voltage or high-current switching. Its on-state resistance and leakage characteristics determine the signal attenuation and off-state isolation introduced into the selected path. Users should evaluate those analog parameters against the impedance and noise requirements of the source and destination circuits. Typical uses include selecting between precision analog signals, routing DAC or ADC channels, controlling communication-system signal paths, and managing audio or video test points. The MAX324CPA+ also suits battery-powered equipment because its low-power operation reduces the energy required when the switch remains in its default state. When designing a PCB, preserve the 8-pin PDIP footprint and route sensitive analog conductors away from digital control traces. Check the supply voltage, control logic levels, and signal amplitude before connecting external circuitry. The manufacturer datasheet pin-description table should be used when assigning tracks and connector positions.

詢價 聯絡我們
MAX324CUA+ - Dual NC SPST Analog Switch | Maxim Integrated
MAX324CUA+

MAX324CUA+ - Dual NC SPST Analog Switch | Maxim Integrated

Maxim Integrated MAX324CUA+ is a dual, single-pole single-throw analog switch with normally closed contacts, 60 ohm on-resistance, 1:1 signal routing, and operation from 2.7V to 16V in an 8-pin uMAX package. The MAX324 family is designed for precision, single-supply analog signal switching. An analog switch is an integrated semiconductor device that routes an electrical signal between terminals under digital control. The MAX324CUA+ belongs to the analog switch category, which sits within interface ICs and broader semiconductor signal-routing systems. Unlike a mechanical relay, it provides compact electronic switching with specified transition timing and low on-resistance. Each internal switch provides a 1:1 connection between its two signal terminals when enabled. The device contains two independent normally closed SPST switches. Their normally closed behavior means the associated signal path remains connected when the control state is inactive, which distinguishes the MAX324 from the normally open MAX323 family. The 60 ohm on-resistance, 100 ns turn-on time, and 150 ns turn-off time define useful operating characteristics for precision analog routing. Single-supply operation from 2.7V to 16V allows the MAX324CUA+ to work with low-voltage control systems as well as higher-voltage analog rails. The control interface supports digital command of the two switches while the switched paths handle analog signals. Because it is an analog switch IC rather than a power MOSFET or regulator, its SOA is not applicable and its primary design concerns are signal integrity, control timing, and off-state behavior. Typical uses include battery-powered instrumentation, sensor signal routing, test-equipment input selection, precision measurement systems, and compact industrial or medical control boards. The 8-pin uMAX package reduces board area, while the dual-switch configuration can control two analog channels from one device. Its 0°C to 70°C commercial temperature rating suits equipment expected to operate within controlled indoor or industrial enclosure environments. When laying out a board, keep the switched analog traces short and place input and output protection close to the external connectors. Confirm that the inactive-state connection matches the circuit's normally closed requirement and check that control timing does not create an unintended transient during switching. This page also organizes functional comparisons and package-specific replacement information for engineers evaluating an existing MAX324 footprint.

詢價 聯絡我們
MAX32550-LCS+T - Secure Cortex-M3 MCU 1MB Flash 121-CTBGA | ADI
MAX32550-LCS+T

MAX32550-LCS+T - Secure Cortex-M3 MCU 1MB Flash 121-CTBGA | ADI

The Analog Devices (formerly Maxim Integrated) MAX32550-LCS+T is an ARM Cortex-M3 based DeepCover secure microcontroller running at 108 MHz, integrating 1 MB of embedded Flash, 256 KB of system RAM, and 8 KB of battery-backed AES self-encrypted NVSRAM, packaged in a 121-ball CTBGA (8x8 mm). The DeepCover security subsystem is purpose-built for trusted devices such as mobile chip-and-PIN payment terminals and PIN pads. A secure microcontroller is an MCU that combines a standard processor core (here, ARM Cortex-M3) with integrated hardware cryptographic engines, secure boot ROM, tamper detection, and physically separate key storage. The MAX32550 belongs to the broader hierarchy: secure MCU -> microcontroller -> embedded processor -> integrated circuit. This device targets financial-terminal OEMs who need both application-class processing power and FIPS-grade security in a single chip. Key features include a 32-bit ARM Cortex-M3 core with 108 MHz maximum clock, 1 MB embedded Flash (1M x 8), 256 KB SRAM, 8 KB AES self-encrypted NVSRAM with battery backup, integrated cryptographic accelerators (AES, DES, SHA, RSA, ECC), hardware True Random Number Generator, secure boot ROM, physical tamper detection pins, an integrated smart-card interface (ISO 7816), magnetic-stripe reader interface, and USB 2.0 Full-Speed with on-chip PHY. The MAX32550 integrates a BGA package with 121 balls on an 8x8 mm body, allowing a compact PCB solution that includes the secure element, application MCU, and physical-tamper mesh interfaces in a single device. The NVSRAM is automatically encrypted with AES-256 keys generated and stored in a dedicated hardware block, removing software-side key management for tamper-sensitive state. The chip targets POS terminal OEMs seeking PCI PTS 4.x/5.x and EMVCo certification. Typical applications include mobile chip-and-PIN payment terminals, PIN pads, POS terminals, secure authentication tokens, EMV smart-card readers, and other financial-grade trusted devices. Industrial secure-control applications such as access-control and hardware security modules also benefit from the integrated tamper mesh. Design consideration: route the battery-backup NVSRAM domain with a separate power rail and a battery cell or super-cap; the cryptographic NVSRAM state is preserved while the rest of the chip powers down. Provide adequate ground-return vias under the CTBGA to meet EMI/magnetic-stripe-decoder noise immunity requirements. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
MAX325EPA+ - Dual Precision SPST Switch | Maxim Integrated
MAX325EPA+

MAX325EPA+ - Dual Precision SPST Switch | Maxim Integrated

Maxim Integrated MAX325EPA+ is a precision, single-supply, dual SPST analog switch with two independently controlled circuits, 1:1 signal routing, and an 8-pin PDIP package. The device operates from 2.7 V to 16 V, has a listed on-resistance of 60 ohm at DigiKey, and is specified as a low-power component consuming approximately 5 microwatts. An analog switch is an integrated semiconductor device that routes electrical signals between circuit nodes under digital control. The MAX325EPA+ belongs to the analog switch hierarchy, which includes multiplexers, selectors, and switch matrices. Its SPST configuration provides one independent normally open connection for each of two channels, making it useful when a system must isolate, route, or protect analog signals without changing the signal level significantly. Key characteristics include two independent SPST channels, single-supply operation from 2.7 V to 16 V, a 60 ohm listed on-resistance, approximately 5 microwatt power consumption, and TTL compatibility when operated from a single 5 V supply. The device is packaged in an 8-pin PDIP measuring 0.300 inch, or 7.62 mm, across the package body. These characteristics suit compact, low-power signal-routing designs where an analog switch must operate from a limited supply rail. The MAX325EPA+ separates analog signal paths from control logic while preserving a straightforward interface. Each switch provides a 1:1 connection when enabled and disconnects the corresponding path when disabled. Single-supply operation simplifies the power architecture in battery-powered instrumentation, but the selected supply voltage and control levels must remain compatible with the switch threshold requirements. In a 5 V system, the device is described as TTL compatible. Typical applications include battery-powered measurement systems, automated test equipment, sensor signal routing, analog input selection, sample-and-hold circuitry, and communication equipment requiring two controllable analog paths. The approximately 5 microwatt power consumption is especially useful in portable equipment where every leakage and static current contributes to battery drain. PCB design should keep each switched trace short and connect the device ground pins to a low-impedance ground plane. Because the MAX325EPA+ uses through-hole PDIP construction, it is most appropriate for leaded assemblies, prototypes, industrial controllers, and test fixtures rather than compact surface-mount production boards. This product page combines distributor availability information, package identification, electrical characteristics, application guidance, and verified replacement information to support faster component selection and board-level planning.

詢價 聯絡我們
MAX32666GXMBT+ - Dual-Core Cortex-M4/M4F BLE 5 MCU | ADI
MAX32666GXMBT+

MAX32666GXMBT+ - Dual-Core Cortex-M4/M4F BLE 5 MCU | ADI

The Analog Devices / Maxim Integrated MAX32666GXMBT+ is a 32-bit dual-core ARM Cortex-M4/M4F microcontroller with FPU, integrated Bluetooth 5 LE radio, hardware security suite, and 1MB Flash, housed in a 121-ball CTBGA (8x8 mm) package. The part operates from 1.71V to 3.6V supply at up to 96MHz core clock and includes 192KB SRAM plus 1MB on-chip Flash. Its dual-core architecture pairs an applications processor with an always-on network co-processor, enabling low-power wearable and IoT designs without sacrificing radio throughput. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O onto one silicon die. The Cortex-M4 family adds a single-precision hardware floating-point unit (FPU) for DSP-class math, and a dual-core MCU further partitions responsibilities - one core runs application logic while the other offloads wireless stack, sensor fusion, or security tasks - reducing wake events and total system energy per task. Key features of the MAX32666GXMBT+ include Bluetooth 5 LE with 2 Mbps high-throughput and 4x long-range PHY modes, ADI TrustZone-style hardware secure element (TRUST), secure boot, true random number generator, AES-256, and SHA-256 accelerators. The integrated DC-DC converter and multiple low-power modes (Active, Sleep, Deep Sleep, Backup, Standby) yield system-level current as low as a few microamps in deep-sleep retention, critical for coin-cell and rechargeable wearables. Architecturally, the part is fabricated in a low-leakage CMOS process and uses ADI's ultra-low-power design IP. The radio block shares the same die as the application cores, eliminating external balun-matching complexity when paired with the recommended chip antenna. Hardware crypto accelerators offload TLS / DTLS handshake workloads so the M4F core can remain idle, further improving energy per transaction. Typical applications include fitness bands and smartwatches, medical wearable patches (continuous glucose monitor, SpO2), secure IoT endpoints (BLE sensor nodes), industrial asset trackers, and hearables / wireless earbuds. The wide 1.71-3.6V supply range supports direct Li-ion battery connection with internal regulation, simplifying the power tree. When designing with this part, allocate the secondary core exclusively to the BLE stack and security; do not share it with general application code. Validate PCB stack-up against the CTBGA escape pattern in the package diagram, and place the DC-DC inductor within 2mm of the LX pin to keep ripple below the AES engine's noise floor.

詢價 聯絡我們
MAX326CPE+ - Quad SPST Low-Leakage Switch | Analog Devices
MAX326CPE+

MAX326CPE+ - Quad SPST Low-Leakage Switch | Analog Devices

The Analog Devices MAX326CPE+ is a quad, single-pole single-throw CMOS analog switch with four independently controlled channels, an on-resistance of 3.5 kΩ, and a 16-pin PDIP package. The device supports supply voltages from 10 V to 30 V and dual supply operation from ±5 V to ±18 V. Its defining characteristic is ultra-low leakage, specified at 10 pA maximum and below 1 pA typical, making it suitable for high-impedance analog paths where switch leakage could disturb the signal. An analog switch is an integrated semiconductor device that connects or disconnects circuit nodes under digital control. The MAX326 belongs to the CMOS analog-switch hierarchy, where each of its four SPST channels provides a normally closed connection that opens when the corresponding control input is asserted. Unlike a mechanical relay, the device changes state electronically and without mechanical wear, making it suitable for precision measurement, signal-routing, and low-leakage test systems. The MAX326CPE+ combines four switch channels in one package and specifies a typical charge injection of 2 pC. The 3.5 kΩ on resistance provides a defined signal-path impedance for moderate-load analog routing. The 10 pA maximum leakage specification limits unintended current transfer across an open switch, while the CMOS and TTL-compatible control interface allows the device to be driven by conventional digital logic. Its operating range from 10 V to 30 V accommodates both single-supply and higher-voltage dual-supply systems. Each SPST channel provides one signal terminal and one common signal terminal, with four independent control inputs. The 16-pin PDIP package exposes the control and analog terminals for straightforward prototyping and through-hole PCB assembly. Because this package is not surface mount, the device is particularly convenient for laboratory instruments, educational platforms, legacy control systems, and prototypes where sockets or plated through-holes are preferred. Typical uses include high-impedance sensor isolation, precision measurement front ends, low-level analog signal routing, automated test equipment, and data-acquisition systems. Its low leakage can preserve small currents and voltages that would be affected by a higher-leakage switch. The principal design consideration is on resistance: although 3.5 kΩ is suitable for many instrumentation signals, applications requiring low source impedance should verify that the resistance and associated signal degradation remain acceptable. For reliable operation, keep every signal and control voltage within the manufacturer's specified absolute maximum ratings, account for switch charge injection during control transitions, and provide adequate logic levels for the selected supply configuration. Review the MAX326 manufacturer datasheet for the complete pin assignment, truth table, switching characteristics, and operating limits before constructing the PCB or choosing external drive circuitry. This product summary combines the manufacturer product-page specifications with practical guidance on leakage, charge injection, supply configuration, package selection, and PCB implementation. It also identifies replacement constraints, allowing engineers to distinguish a true pin-compatible substitute from a merely similar quad-SPST device before committing a new design to production.

詢價 聯絡我們
MAX33040EAKA+ - +3.3V 5Mbps CAN Transceiver, ±40V Fault, SOT-23-8 | Maxim Integrated
MAX33040EAKA+

MAX33040EAKA+ - +3.3V 5Mbps CAN Transceiver, ±40V Fault, SOT-23-8 | Maxim Integrated

The Maxim Integrated MAX33040EAKA+ is a +3.3V control area network (CAN) bus transceiver with integrated overvoltage and ESD protection, housed in an 8-pin SOT-23 package. It supports data rates up to 5 Mbps, offers ±40V fault protection on the CANH and CANL bus pins, ±40 kV ESD HBM protection, and ±25V common-mode range, exceeding the ISO 11898-2 CAN physical-layer standard. A CAN transceiver (also called a CAN physical-layer device) sits between a microcontroller's CAN protocol controller and the differential CAN bus wires. It converts the microcontroller's digital TX/RX logic levels into the differential dominant/recessive voltages defined by ISO 11898-2, and simultaneously protects the sensitive MCU side from harsh automotive and industrial bus transients. Within the broader hierarchy, a CAN transceiver falls under Interface ICs > Wired Communication > CAN/LIN transceivers. Key features include a 3V to 3.6V single-supply operating range, low-current standby and silent modes, hot-plug capability, slope control for limited-data-rate applications, and TXD dominant-timeout to prevent bus lockup from a stuck dominant node. The SOT-23-8 footprint occupies roughly 9 mm² of board area, making it one of the smallest isolated-fault CAN transceivers available. Internally the device combines a differential CAN driver/receiver pair with TVS-based fault clamps and an ESD cell rated to ±40 kV HBM. The wide ±25V CMR allows it to reject large ground-shift noise typical of long industrial cables and 12V/24V battery-powered equipment, while the ±40V fault tolerance survives load-dump and jump-start events far beyond the ISO 7637 pulse ratings. Typical applications include building automation gateways, industrial drones and motor controllers, factory-floor sensors, instrumentation data links, service and educational robots, and any 3.3V MCU-based system that must communicate reliably over CAN. Its small SOT-23-8 package and integrated ±40V/±40kV protection eliminate the need for external TVS diodes, common-mode chokes, and isolation in many designs. When designing with the MAX33040EAKA+, observe the bus-termination requirement of two 120 Ω resistors (one at each end of the bus) and place a 100 nF decoupling capacitor as close as possible to the VCC pin. The SLP pin can be tied high for low-speed, slope-controlled operation or left open for normal high-speed mode.

詢價 聯絡我們
MAX332CPE+ - Quad SPST 175Ω Analog Switch | Analog Devices
MAX332CPE+

MAX332CPE+ - Quad SPST 175Ω Analog Switch | Analog Devices

The Analog Devices MAX332CPE+ is a four-circuit, normally open analog switch with a 175Ω on-resistance, packaged in a 16-pin PDIP. It provides 1:1 signal routing, a typical turn-on time of 1 µs, and a typical turn-off time of 500 ns, making it suitable for analog and digital signal-path switching. An analog switch is a semiconductor device that connects or disconnects a signal path under digital control. Within the component hierarchy, the MAX332CPE+ is an analog switch, also classified as a multiplexer or demultiplexer when used to route one of several lines to a common node. Its four independent SPST switches can isolate, select, or disconnect external circuit nodes. The MAX332CPE+ uses four normally open switch circuits to provide straightforward routing without a break-before-make interpretation in the product description. Its documented 175Ω on-resistance supports practical signal interconnection, while 1 µs turn-on and 500 ns turn-off timing suit control systems that need switching in the microsecond range. The 16-pin PDIP format supports conventional through-hole PCB assembly. The device is identified as a quad SPST, 1:1 analog switch with a 16-pin PDIP package. Its four-circuit architecture consolidates multiple switch functions into one package, reducing component count compared with four single-switch devices. The device is implemented as a CMOS analog switch and is intended for controlled routing of external signals rather than power conversion or high-current switching. Typical uses include signal-path isolation in test and measurement equipment, channel selection in analog front ends, sample-and-hold control paths, instrumentation interfaces, and industrial control systems. In each case, the control logic selects one of the available connections while the switch network separates the selected source from the other external nodes. Designers should verify the exact control states, pin mapping, supply requirements, allowable signal levels, and switching conditions in the Maxim Integrated datasheet before laying out a PCB. The PDIP package is mechanically straightforward to route, but the switch nodes should be positioned to minimize coupling between adjacent high-impedance paths and to keep control traces away from sensitive analog conductors. This product page combines the confirmed switch configuration, timing, resistance, and package characteristics with application guidance, engineering considerations, and drop-in alternatives. It is designed to help engineers identify the correct device faster while preserving the distinction between verified MAX332CPE+ attributes and replacement-specific data that must be checked before procurement.

詢價 聯絡我們
MAX333CPP+ - Quad SPDT CMOS Analog Switch | Maxim Integrated
MAX333CPP+

MAX333CPP+ - Quad SPDT CMOS Analog Switch | Maxim Integrated

The Maxim Integrated MAX333CPP+ is a quad, independent SPDT CMOS analog switch with four 2:1 channels, 250 ohm on-resistance, and a 20-pin PDIP package. It supports bipolar supplies from ±5 V to ±18 V or single-ended supplies from +10 V to +30 V, while its TTL- and CMOS-compatible control inputs operate from +0.8 V to +2.4 V. Break-before-make switching is 200 ns typical. A CMOS analog switch is a voltage-controlled semiconductor device that routes analog signals between circuit nodes under digital control. An SPDT switch provides one common connection and two switched terminals, allowing a signal to select between two paths. The MAX333 belongs to the analog-switch hierarchy within interface ICs, where low on-resistance, controlled switching behavior, and broad supply-voltage support are important for signal routing and test systems. The MAX333CPP+ combines four independent SPDT switches in one package. Its 250 ohm on-resistance supports general-purpose analog routing, while break-before-make operation prevents the two switched paths from being connected simultaneously during transition. The control inputs accept both TTL and CMOS logic levels across a +0.8 V to +2.4 V input range. Logic inputs and switched analog signals may operate anywhere between the supply rails without damage, according to the manufacturer datasheet. The device can operate from dual bipolar supplies or a single-ended supply. Its switching architecture is intended to provide low-cost replacement of a DG211 and DG212 pair when four SPDT channels are required. The 200 ns typical break-before-make timing is relevant when the switched network must avoid momentarily connecting two sources together. Analog signal amplitude, supply polarity, control timing, and channel isolation remain important system-level constraints. Typical uses include analog measurement systems, signal multiplexing, instrumentation, communications equipment, and industrial control modules where several independently controlled analog paths are needed. Each switch can route a sensor, reference, or test signal without requiring a separate discrete switch package for every channel. The quad integration reduces board area and simplifies control logic, although all four channels still require careful consideration of signal loading and supply bypassing. For layout, place the device close to the signals being routed and keep analog traces away from high-speed digital switching nodes. Keep power-ground and signal-ground returns compact, and follow the pin-description table in the manufacturer datasheet when assigning PCB tracks. Designers should verify the maximum analog and logic voltages, supply configuration, and off-state behavior against the exact operating conditions before production release. This page combines the manufacturer switching characteristics with package, application, replacement, and PCB-oriented guidance. It also identifies pin-compatible family options and clarifies the electrical constraints that matter when evaluating the MAX333CPP+ as a quad SPDT routing element.

詢價 聯絡我們