AD506JH - Low-Noise JFET Op Amp, TO-99-8 | Analog Devices
MPN: AD506JH ✓ 啟用中AD506JH 概覽
A JFET-input operational amplifier is a voltage-amplifier type whose input stage uses junction field-effect transistors rather than bipolar transistors. Within the signal-chain hierarchy, the AD506JH belongs to the operational-amplifier family, where it sits between passive sensors and analog-to-digital converters, active filters, instrumentation amplifiers, and laboratory measurement equipment. JFET inputs are valued for high input impedance and low bias currents when working with high-impedance sources.
The key features of the AD506JH include a JFET input stage, a single-amplifier configuration, a 10 V to 40 V operating supply span, and a -55 °C to 125 °C temperature range. Its TO-99-8 package is a through-hole metal can with a package pitch that differs from modern surface-mount op amps. Designers should therefore treat the AD506JH as a heritage-style precision amplifier rather than a drop-in choice for an 8-pin dual op-amp footprint.
Because the AD506JH operates from a minimum supply of 10 V, it is intended for split-supply or higher-voltage analog systems rather than 3.3 V or 5 V rail operation. The metal-can package also limits the practicality of high-volume automated assembly when compared with SOIC, TSSOP, or QFN alternatives. Nevertheless, the package supports conventional through-hole insertion and is useful in laboratory, industrial, and legacy control equipment where long service life and temperature stability are more important than board area.
Typical uses include precision current-to-voltage conversion, low-level sensor amplification, active filtering, bridge-sensor signal conditioning, and instrumentation front ends. The wide supply range allows the amplifier to operate from a 24 V industrial rail, while its low-noise JFET input stage is appropriate for sources with high source impedance. Offset-voltage, input-bias-current, input-voltage-noise, and open-loop-gain values should be confirmed in the manufacturer datasheet before setting gain or bias networks.
The main design consideration is the supply headroom required by the output stage. Feedback networks should use stable, low-temperature-coefficient resistors, and the unused amplifier positions are not applicable because the package contains only one amplifier. Keep sensitive input traces short, protect the input nodes from leakage and contamination, and use adequate bypassing between the supply pins and the common terminal according to the datasheet recommendations.
This page combines the AD506JH package, supply, temperature, and circuit configuration with practical guidance on high-impedance sensing, legacy through-hole layout, and component selection. It also distinguishes true same-family replacements from modern op amps that share a pin count but not a footprint or electrical architecture.
直接替換替代品,適用於 AD506JH — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: AD506JH (相同外形與佔位) — 差異在於 Product Type.
AD506AH
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD506BH
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD506JH 最大額定值與電氣特性
| Product Type | Single JFET-input operational amplifier |
| Number of Amplifier Circuits | 1 circuit |
| Input Stage | JFET |
| Supply Voltage Span | 10 V to 40 V |
| 工作溫度範圍 | -55 °C to 125 °C |
| 封裝 | TO-99-8 metal can |
| 安裝類型 | Through-hole |
| 腳位數 | 8 pins |
| RoHS 狀態 | RoHS |
AD506JH to-99-8 metal can 腳位配置指南
AD506JH(to-99-8 metal can 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD506JH.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD506JH 適用於 6 應用s: Precision Current-to-Voltage Conversion, High-Impedance Sensor Signal Conditioning, Precision Active Filtering, Bridge Sensor Front End, Laboratory Instrumentation Signal Chain, Legacy Industrial Control Retrofit.
Precision Current-to-Voltage Conversion
The AD506JH fits a precision I-to-V converter because its JFET input stage suits high-impedance feedback networks and its 10 V to 40 V supply span accommodates ±15 V laboratory rails. Place the amplifier in a standard inverting configuration and return the feedback network to the inverting input. The single-amplifier TO-99-8 package avoids the unused channel found in dual op amps, while the -55 °C to 125 °C range supports demanding temperature environments. Confirm input bias current, input capacitance, and output-swing limits before choosing the sense-resistor value and feedback resistor.
High-Impedance Sensor Signal Conditioning
The AD506JH is appropriate for conditioning signals from high-impedance sensors where input bias current and leakage can create measurement errors. Its JFET input supports the high input impedance normally required by photodiode, capacitive, or electrochemical sensor interfaces, while the wide supply range allows operation from a 24 V-based analog system. Use short, guarded input traces and clean guarding around the high-impedance node to reduce leakage pickup. Validate the required bandwidth and noise against the complete amplifier characteristics in the AD506 datasheet.
Precision Active Filtering
The AD506JH can implement precision active filters where a low-noise, high-impedance input stage is valuable. Its single amplifier supports Sallen-Key, multiple-feedback, and instrumentation-style networks using the feedback components specified by the filter design. The 10 V to 40 V supply span provides comfortable headroom for bipolar signals on ±15 V rails, and the metal-can package helps maintain a stable, serviceable through-hole assembly. Use precision resistors and capacitors, and verify the amplifier gain-bandwidth and slew-rate requirements against the highest operating frequency.
Bridge Sensor Front End
The AD506JH is a candidate for the amplifier section of a resistive bridge sensor interface where low input bias current helps preserve the differential sensor signal. Its high input impedance limits loading of the bridge, and the -55 °C to 125 °C operating range is useful in industrial and laboratory environments. Use an instrumentation-amplifier topology or carefully matched differential stage, and keep bridge excitation wiring away from sensitive input routing. Confirm input offset voltage, common-mode rejection, and bias-current drift against the accuracy budget.
Laboratory Instrumentation Signal Chain
The AD506JH suits laboratory instrumentation that requires a single precision amplifier operating from higher-voltage analog rails. It can amplify weak sensor outputs ahead of a comparator, ADC input stage, or data-acquisition channel while preserving a high source impedance. The TO-99-8 through-hole package supports manual assembly, rework, and replacement in long-lived analytical equipment. Provide regulated bypassing, observe the package pin one orientation, and verify the input and output ranges over the full -55 °C to 125 °C operating range.
Legacy Industrial Control Retrofit
The AD506JH is useful for maintaining legacy industrial control, test, and analog-processing equipment that uses an eight-lead TO-99-8 single JFET-input amplifier. The wide supply span and extended temperature range support retrofit applications in equipment originally designed around higher-voltage rails. Preserve the original lead arrangement, offset-trim connections, and feedback topology unless the manufacturer application information provides an authorized change. Confirm availability and lifecycle status through the Request a Quote form before scheduling a production or field replacement.
工程參考資料,適用於 AD506JH — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD506AH | AD506BH |
|---|---|---|---|
| Package | TO-99-8 metal can | TO-99-8 metal can | TO-99-8 metal can |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Circuits | 1 circuit | 1 circuit | 1 circuit |
| Input Stage | JFET | JFET | JFET |
| Supply Voltage Span | 10 V to 40 V | 10 V to 40 V | 10 V to 40 V |
| Mounting Type | Through-hole | Through-hole | Through-hole |
| Pin Count | 8 pins | 8 pins | 8 pins |
主要差異化特點
- Single-amplifier precision configuration (對比AD506AH)
- Extended AD506JH operating temperature rating (對比AD506AH)
- Direct compatibility with the AD506 family architecture (對比AD506BH)
設計說明
The AD506JH requires a 10 V to 40 V total supply, so a ±15 V source is a natural operating point for bipolar signal chains. Place the supply-bypass capacitors close to the relevant supply and common leads, and use low-inductance routing between the package and the capacitors. Check the output-swing limits in the manufacturer datasheet before designing a circuit that must approach either supply rail.
Keep the inverting-input and feedback traces short because the TO-99-8 lead pitch is long relative to modern surface-mount packages. Route sensitive inputs away from the supply leads and bypassing-current return paths, and avoid parallel copper runs beneath a high-impedance input node. Observe pin-one orientation from the package drawing and confirm the balance and offset connections before energizing the circuit.
Do not treat an ordinary 8-pin dual op amp as a replacement merely because both packages have eight leads. The AD506JH is a single amplifier in a TO-99-8 metal can, and its offset-trim and balance pins have specific family functions. Validate footprint, lead numbering, supply range, bias current, offset voltage, and compensation requirements before substituting a modern amplifier.
For high-impedance sources, minimize leakage from board contamination, flux residue, and protection diodes. Use guarding where practical, keep the input node away from large voltage gradients, and clean the assembled PCB. Because input bias current is not stated in the available catalog data, use the manufacturer value to estimate the voltage error produced by the source and feedback resistances.
合規資訊
The LCSC product listing identifies the AD506JH as RoHS compliant. No additional compliance declarations are stated in the available catalog information.