AD623BNZ - Rail-to-Rail Instrumentation Amplifier | Analog Devices
MPN: AD623BNZ ✓ 啟用中AD623BNZ 概覽
An instrumentation amplifier is a differential-input signal-conditioning IC that amplifies the voltage difference between two inputs while providing high input impedance and accurate differential gain. Within the analog signal-chain hierarchy, an instrumentation amplifier combines input-stage behavior, differential amplification, and output buffering in one package. It is commonly used where a small sensor signal must be measured accurately in the presence of common-mode voltage, source impedance, or grounding constraints.
The AD623 supports single-supply operation from 2.7 V to 12 V and also supports dual supplies. Its rail-to-rail output allows the output to approach the available supply range, improving utilization of limited power budgets. A user-programmable gain resistor provides gain adjustment, while the 800 kHz bandwidth supports signals extending well above audio frequency. The 0.3 V/µs slew rate provides useful response capability for moderate-bandwidth measurement systems.
The integrated three-op-amp architecture supports differential input sensing while maintaining high common-mode rejection when component matching and resistor accuracy are adequate. Gain is established with an external resistor rather than a fixed internal network, allowing the circuit designer to select sensitivity according to sensor output, analog input range, and required resolution. Careful reference-grounding and resistor selection remain essential because gain accuracy and common-mode rejection depend on these external implementation details.
Typical uses include bridge-transducer excitation and sensing, biomedical instrumentation, current monitoring, industrial process measurement, sensor interfaces, and portable data-acquisition systems. In a bridge circuit, the AD623 measures differential millivolt-level excitation changes while rejecting much of the common supply voltage. In a current-shunt monitor, it amplifies the voltage generated across the shunt without substantially loading the measured conductor.
Design with the 2.7 V to 12 V supply limits in mind, including input and output headroom at the selected supply voltage. Place bypass capacitors close to the supply pins, use a clean ground reference for the measurement system, and verify that source impedance and gain-resistor values do not compromise accuracy. The rail-to-rail output simplifies low-voltage operation but does not eliminate the need to check output swing under load.
This page combines the AD623BNZ electrical characteristics, package information, application guidance, comparison parameters, and verified replacement considerations to support faster component evaluation and PCB design.
直接替換替代品,適用於 AD623BNZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: AD623BNZ (相同外形與佔位) — 差異在於 Gain Programming, Package, Product Type.
AD623BNZ 最大額定值與電氣特性
| Product Type | Single-circuit instrumentation amplifier |
| Supply Voltage Range | 2.7 V to 12 V |
| Single-Supply Operation | Supported |
| Dual-Supply Operation | Supported |
| Output Swing | Rail-to-rail |
| Bandwidth | 800 kHz |
| Slew Rate | 0.3 V/µs |
| Input Offset Voltage | 100 µV maximum |
| Number of Amplifiers | 1 circuit |
| Gain Programming | User-programmable resistor |
| 封裝 | 8-pin PDIP |
| 腳位數 | 8 pins |
| 安裝類型 | Through-hole PDIP |
AD623BNZ 8-pin pdip 腳位配置指南
AD623BNZ(8-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD623BNZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD623BNZ 適用於 6 應用s: Bridge Sensor Signal Conditioning, Portable Biomedical Sensor Interface, Industrial Current-Shunt Monitoring, Process Pressure and Flow Measurement, Portable Data Acquisition, Balanced Audio Measurement.
Bridge Sensor Signal Conditioning
The AD623BNZ fits strain-gauge, load-cell, and resistive bridge interfaces because it amplifies the small differential voltage generated by changes in bridge resistance. Its 2.7 V to 12 V supply range supports compact low-voltage measurement systems, while the 800 kHz bandwidth comfortably covers many static and dynamic mechanical measurements. The bridge excitation defines the available differential signal, so gain must be selected to keep the output within the rail-to-rail swing range. Use a clean reference ground and place the gain resistor where its value and tolerance can be controlled accurately.
Portable Biomedical Sensor Interface
The AD623BNZ is suitable for portable biomedical sensing when the measured signal is differential and the system requires rail-to-rail output from a low-voltage supply. Operation down to 2.7 V supports battery-powered instrumentation, and the 800 kHz bandwidth accommodates many physiological and biosensor signals. The 100 µV maximum offset specification can be important when resolving small sensor outputs, although electrode impedance, patient protection, isolation, leakage, and medical qualification require separate evaluation. A high-impedance source and carefully grounded reference are especially important for low-level bioelectric measurements.
Industrial Current-Shunt Monitoring
The AD623BNZ can amplify the differential voltage across a current-sense shunt without directly interrupting the measured current path. Its differential-input architecture reduces sensitivity to the supply rail common to both shunt terminals, and the 0.3 V/µs slew rate supports moderate transient response. The 2.7 V to 12 V range supports both compact control systems and higher-voltage industrial rails. Select gain so that maximum expected current remains inside the output-swing range, and use Kelvin routing to avoid including copper and connector resistance in the measurement.
Process Pressure and Flow Measurement
The AD623BNZ is appropriate for process-control front ends that receive low-level differential signals from pressure, level, or flow transmitters. The instrumentation-amplifier configuration handles the difference between paired sensor outputs while rejecting much of their common-mode voltage. Its rail-to-rail output improves signal range in 3.3 V and 5 V systems, and the 800 kHz bandwidth is suitable for many flow and pressure loops without requiring a high-speed amplifier. Validate the transmitter output range, grounding method, and isolation requirements before connecting field wiring to the measurement circuit.
Portable Data Acquisition
The AD623BNZ supports compact data-acquisition modules that measure sensor outputs under a 2.7 V to 12 V supply budget. Single-supply operation reduces system complexity, while rail-to-rail output permits the converter to use most of the available signal range. The 800 kHz bandwidth is suitable for many sensor channels requiring accurate amplification rather than high-frequency signal capture. The external gain resistor makes sensitivity easy to adapt across channels, although resistor tolerance and drift should be included in the total measurement uncertainty calculation.
Balanced Audio Measurement
The AD623BNZ can condition balanced audio or other differential signals when a single-supply measurement system is preferred. Its rail-to-rail output is useful in 5 V test equipment, and the 800 kHz bandwidth covers the full audio band with additional margin. The differential architecture helps reject common-mode hum or ground-potential differences that could otherwise affect the result. Use a stable gain resistor, maintain symmetrical input routing, and verify that the source impedance does not degrade CMRR or create excessive gain error.
工程參考資料,適用於 AD623BNZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD623ANZ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 8-pin PDIP | 8-pin PDIP |
| Product Type | Instrumentation amplifier | Instrumentation amplifier |
| Number of Circuits | 1 circuit | 1 circuit |
| Supply Voltage Range | 2.7 V to 12 V | 2.7 V to 12 V |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Bandwidth | 800 kHz | 800 kHz |
| Slew Rate | 0.3 V/µs | 0.3 V/µs |
| Input Offset Voltage | 100 µV maximum | 25 µV maximum |
| Gain Programming | User-programmable resistor | User-programmable resistor |
主要差異化特點
- Single-supply operation extends to 2.7 V (對比AD623ANZ)
- Rail-to-rail output improves low-voltage signal range (對比AD623ANZ)
- 8-pin PDIP supports through-hole assembly (對比AD623ANZ)
設計說明
Place the supply bypass capacitor immediately beside the AD623BNZ supply and ground pins, with a short, low-inductance return path. The AD623 datasheet specifically recommends capacitive decoupling close to the power pins. Keep sensitive gain-resistor and feedback paths away from switching nodes and high-current return paths to avoid converting supply and ground disturbances into measurement error.
Do not assume that rail-to-rail output means the output can reach either supply rail under every load. Check the loaded output-swing limits, input common-mode range, and gain calculation from the manufacturer datasheet. At 2.7 V or 3.3 V operation, the available signal span and external gain resistor may need more conservative values than at 5 V or 12 V.
Route the two differential inputs as a balanced pair and connect their returns without unintended loops. Use a single low-noise ground reference for the sensor and instrumentation amplifier unless the system design requires an isolation barrier. For a current shunt, use Kelvin connections so copper resistance and solder-joint resistance are not included in the measured shunt voltage.
Include gain-resistor tolerance and temperature coefficient in the error budget rather than relying only on the nominal gain equation. Differential input bias current and source-imbalance effects can create additional output error. Use a resistor value recommended by the manufacturer where practical, and verify the complete signal chain with the actual sensor source impedance and cable length.
合規資訊
Compliance status is not established in the product information available for the exact AD623BNZ suffix. Request current supporting declarations when ordering.