AD647SE - Ultralow Drift Dual JFET Amplifier | Analog Devices
MPN: AD647SE ✗ 停產AD647SE 概覽
An operational amplifier is an active feedback component that amplifies the difference between its two inputs. The AD647SE belongs to the JFET-input operational-amplifier hierarchy, within precision analog amplifiers and signal-conditioning ICs. Unlike bipolar-input amplifiers, its JFET input stage draws very low bias current, making it suitable for high-impedance sensors, guarding structures, sample-and-hold circuits, and measurement front ends. Its monolithic construction also places two closely matched amplifiers in one package.
Key features include an ultralow-drift architecture, ion-implanted matched JFETs on a monolithic bipolar chip, and laser wafer drift trimming. The dual-amplifier configuration allows differential or instrumentation-style signal processing while reducing board area and package count. The 20-pin CLLCC ceramic package supports applications that require a robust hermetic-style device package, while the ±18 V operating capability permits conventional dual-supply analog circuits.
The AD647’s input stage is implemented with ion-implanted JFETs on a monolithic bipolar chip. This process provides closely matched input devices, while laser wafer trimming is used to reduce offset-voltage drift. The practical result is an amplifier intended for accurate current-to-voltage conversion, low-level sensing, and feedback loops where changes in input offset voltage can degrade measurement accuracy. Unlike a general-purpose high-speed amplifier, its design prioritizes drift performance and input behavior rather than slew rate or wide-band bandwidth.
Typical uses include precision instrumentation, low-level sensor conditioning, bridge and current-feedback measurement paths, laboratory test equipment, and high-impedance buffer stages. Two amplifiers in one package can also support differential excitation or paired active-feedback circuits when channel matching is important. Because the AD647SE is an older precision amplifier, engineers should verify availability and current lifecycle status before committing it to a new production design.
For stable operation, keep the feedback network and compensation components close to the device, maintain the specified common-mode and supply limits, and avoid relying on a high-speed layout for this drift-optimized amplifier. Decoupling capacitors should be placed directly beside the supply pins, while sensitive input traces should be guarded and kept away from switching nodes. The ceramic package also requires attention to lead alignment and thermal conditions during soldering.
This page combines the manufacturer’s device description with package identification, practical application guidance, and drop-in replacement research. The replacement shortlist is intentionally limited to package-compatible military-order variants because the available cross-reference results do not establish five distinct same-package drop-in amplifiers. This avoids presenting merely similar JFET amplifiers as direct PCB replacements.
直接替換替代品,適用於 AD647SE — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: AD647SE (相同外形與佔位) — 差異在於 Amplifier Type, Supply Voltage Range.
AD647SE/883B
✅ 直接替換聯絡詢價
查看資料表 →AD647SE/883BH
✅ 直接替換📋 參考替代品(不在目錄中)
AD647SE 最大額定值與電氣特性
| Amplifier Type | Dual precision JFET-input operational amplifier |
| Number of Amplifiers | 2 |
| Supply Voltage Range | ±18 V |
| Input Transistor Technology | Ion-implanted JFET on a monolithic bipolar chip |
| Offset Trimming | Laser wafer drift trimming |
| 封裝 | 20-pin CLLCC ceramic leaded chip carrier |
AD647SE 20-pin cllcc ceramic leaded chip carrier 腳位配置指南
AD647SE(20-pin cllcc ceramic leaded chip carrier 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD647SE.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD647SE 適用於 6 應用s: Precision Current-to-Voltage Conversion, High-Impedance Sensor Signal Conditioning, Bridge and Instrumentation Measurement, Laboratory Instrumentation Front End, Active Feedback and Probe Buffering, Low-Level Signal Amplification.
Precision Current-to-Voltage Conversion
The AD647SE is appropriate for precision current-to-voltage conversion because its JFET inputs minimize disturbance to high-impedance current sources while the ultralow-drift architecture limits input-offset changes with temperature. Place the amplifier in a transimpedance configuration and use the two channels for either paired conversion channels or a differential auxiliary signal. The 20-pin CLLCC package provides a single ceramic package for sensitive analog circuitry. Confirm input-bias-current, common-mode-range, and compensation requirements from the manufacturer datasheet before setting the feedback resistor, because those values determine stability and usable transimpedance bandwidth.
推薦
High-Impedance Sensor Signal Conditioning
The AD647SE can condition signals from high-impedance sensors because its JFET input stage reduces input bias-current loading compared with a conventional bipolar-input precision amplifier. Its ultralow drift behavior is useful when a small sensor output must remain accurate over changing temperature. Use the matched dual channels for complementary sensing or differential instrumentation, and protect sensitive nodes with guarding, clean connectors, and short PCB traces. The usable common-mode voltage, input capacitance, and settling behavior must remain within the manufacturer limits, particularly for capacitive sensors where leakage and stability can dominate the measurement error.
推薦
Bridge and Instrumentation Measurement
The AD647SE fits bridge and instrumentation measurements where offset drift can obscure a small differential signal. Two JFET-input amplifiers in one ceramic package provide the basis for instrumentation-style signal handling, while ion-implanted matching supports closely related channel behavior. Place both amplifier inputs symmetrically to minimize thermal gradients and keep the bridge excitation and return paths away from sensitive input traces. Select resistor values for the required excitation current and differential range, then verify input common-mode limits under worst-case bridge imbalance. The amplifier should be evaluated for temperature drift, offset behavior, noise, and stability before being used as the final measurement chain.
推薦
Laboratory Instrumentation Front End
The AD647SE is suitable for laboratory instrumentation front ends that amplify small sensor or source signals while maintaining low input loading and predictable offset behavior. The dual arrangement can implement two channels without duplicating the ceramic package, and the ultralow-drift architecture is valuable in equipment expected to maintain calibration over temperature. Use short, guarded input paths and isolate the amplifier from high-current return paths that could create ground-potential errors. Because this is a legacy precision JFET amplifier, validate current availability and the required temperature range before finalizing a laboratory product, and use the manufacturer application information as the basis for compensation and layout.
推薦
Active Feedback and Probe Buffering
The AD647SE can serve as an active-feedback or probe-buffering stage when the source presents high impedance and the amplifier must avoid introducing excessive bias-current error. The JFET input architecture supports low-load operation, while the matched dual channels can buffer or monitor two related probes. Keep the input node physically compact and use guarding to reduce leakage and surface contamination when handling femtoamp- or picoamp-scale signals. Compensation and bandwidth must be checked for the feedback network rather than inferred from general-purpose amplifier expectations. The ±18 V capability accommodates conventional laboratory rails, but the complete input and output ranges still define the safe operating envelope.
推薦
Low-Level Signal Amplification
The AD647SE is intended for low-level signal amplification where offset drift and input loading can compromise measurement accuracy. Its ultralow-drift JFET-input architecture makes it suitable for conditioning weak signals ahead of an ADC or measurement system, while the dual package can process a main channel and a reference or monitor channel. Define the smallest signal of interest, acceptable input-referred error, and required bandwidth before choosing the feedback network. Place compensation and gain-setting components close to the device, maintain symmetric routing, and keep switching converters and digital clocks away from the sensitive input. Validate noise, offset, common-mode range, and settling in the complete analog chain.
推薦
推薦產品摘要
工程參考資料,適用於 AD647SE — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD647SE/883B | AD647SE/883BH |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-pin CLLCC ceramic leaded chip carrier | 20-pin CLLCC | 20-pin CLLCC |
| Amplifier Configuration | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
| Input Stage | JFET input | JFET input | JFET input |
| Primary Design Objective | Ultralow drift | Ultralow drift | Ultralow drift |
| Maximum Supply Voltage | ±18 V | ±18 V | ±18 V |
| Matching Technology | Ion-implanted JFETs on a monolithic bipolar chip | Ion-implanted JFETs on a monolithic bipolar chip | Ion-implanted JFETs on a monolithic bipolar chip |
| Offset Adjustment Method | Laser wafer drift trimming | Laser wafer drift trimming | Laser wafer drift trimming |
| Ordering Designation | AD647SE | /883B screened ordering designation | /883BH screened ordering designation |
主要差異化特點
- Dual matched JFET channels in one ceramic package (對比AD647SE/883B)
- Ultralow-drift positioning (對比AD647SE/883BH)
- Low-bias-current JFET input architecture (對比AD647SE/883B)
設計說明
Treat the AD647SE as a precision analog device even though it is not a high-speed amplifier. Route both channels symmetrically, keep gain-setting and compensation components close to their associated pins, and avoid routing sensitive inputs beneath or beside switching nodes. The ceramic CLLCC package also requires solder-assembly controls that maintain straight leads and adequate thermal contact without introducing mechanical stress.
Use guarding and leakage control on high-impedance inputs. Keep input traces short, clean, and surrounded by a grounded guard where appropriate; surface contamination and humid assembly residues can create leakage comparable to the currents being measured. Place power-supply bypass capacitors immediately across the relevant supply pins and provide a quiet return path so supply current does not modulate the input-reference potential.
Do not assume that every part sharing the AD647 family name has interchangeable screening, temperature, or marking requirements. Confirm the exact order code, pinout, supply limits, common-mode range, offset specifications, and package drawing before replacing AD647SE with an /883 ordering variant. Also verify the stability and compensation requirements of the selected feedback network instead of applying values from a different amplifier topology.
The ceramic package provides a suitable thermal path, but the amplifier still requires airflow or PCB heat-spreading appropriate to its dissipation. Monitor the junction-temperature rise during maximum output swing and worst-case supply operation. Keep the device away from localized heat sources and verify temperature drift at the actual enclosure temperature, since drift performance is most meaningful across the complete intended environmental range.
合規資訊
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified for AD647SE. The /883 ordering variants suggest a screened ordering context, but their qualification and environmental requirements must be confirmed from the manufacturer documentation.