ADM241LAR - 120 kbps 4/5 RS-232 Transceiver | Analog Devices
MPN: ADM241LAR ✓ 啟用中ADM241LAR 概覽
An RS-232 transceiver is an interface IC that combines line drivers and line receivers for serial data links using the EIA-232-E and V.28 specifications. The driver channels convert low-voltage logic signals into bipolar RS-232 levels, while the receiver channels convert bipolar line signals back into logic levels. This integrated transceiver category reduces the number of external components required where both transmission and reception are needed in the same equipment.
Key features include a single 5 V power supply, four drivers, five receivers, 120 kbps operation, and on-board DC-DC converters that generate approximately ±9 V output swing. The interface uses small 1 µF charge-pump capacitors and includes a low-power shutdown mode in which supply current is no more than 1 µA. Receiver inputs withstand voltages up to ±30 V, improving tolerance to exposed serial-port wiring and transients.
The integrated charge-pump architecture eliminates the need for an external ±12 V supply, making the ADM241LAR appropriate for equipment that otherwise operates entirely from 5 V. Its five receivers provide one more receive channel than its four driver channels, which supports designs with an additional receive-only signal, an echo-detection path, or a status input. The 28-pin SOIC package also offers a larger lead pitch than fine-pitch packages, easing assembly and inspection.
Typical applications include industrial serial-port adapters, data-acquisition equipment, test and measurement instruments, point-of-sale terminals, barcode scanners, and embedded control systems that exchange RS-232 data with external peripherals. The interface is especially useful when the host lacks a native RS-232 transceiver and the connected equipment requires bipolar signaling rather than a 3.3 V or 5 V logic-level serial port.
Design the charge-pump capacitor network and input/output protection for the voltage and current limits stated in the Analog Devices datasheet. Keep the connector-side interface path physically separated from sensitive logic and power traces, provide the required bypass capacitance near the supply pins, and verify signal integrity at the intended baud rate before treating the 120 kbps figure as a guaranteed system-level result.
This product page organizes the ADM241LAR’s interface characteristics, package information, sourcing path, design guidance, and replacement considerations into a compact engineering reference. It also distinguishes verified device identity from compatibility checks that must still be completed before approving any substitute in an existing PCB design.
直接替換替代品,適用於 ADM241LAR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
HIN213CAZ-T
✅ 直接替換📋 參考替代品(不在目錄中)
ADM241LAR 規格
| Product Type | RS-232 transceiver |
| 供應電壓 | 5 V |
| Driver Channels | 4 |
| Receiver Channels | 5 |
| Maximum Data Rate | 120 kbps |
| Driver Output Swing | Approximately ±9 V |
| Charge-Pump Capacitor Value | 1 µF |
| Shutdown Supply Current | ≤1 µA |
| Receiver Input Voltage Tolerance | ±30 V |
| Interface Standard | EIA-232-E and V.28 |
| Integrated DC-DC Converter | Yes |
| Logic Technology | CMOS |
| 封裝 | 28-pin SOIC |
| 安裝類型 | Surface Mount |
ADM241LAR 28-pin soic 腳位配置指南
ADM241LAR(28-pin soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ADM241LAR.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADM241LAR 適用於 6 應用s: Industrial Serial-Port Adapter, Data-Acquisition Equipment, Test and Measurement Instrument, Point-of-Sale Terminal, Barcode Scanner Interface, Embedded Control Communication.
Industrial Serial-Port Adapter
The ADM241LAR fits a 5 V industrial adapter that must communicate with legacy RS-232 equipment while the host processor exposes only logic-level serial signals. Its four drivers and five receivers support multiple data and handshake paths, while the integrated DC-DC converters remove the need for a separate ±12 V rail. The 120 kbps capability accommodates common serial-device rates, although the complete link should be tested with the intended cable length and grounding arrangement.
Data-Acquisition Equipment
The ADM241LAR can provide the physical RS-232 layer for a data-acquisition unit that must exchange commands and measurements with a laboratory computer or controller. The five receiver channels leave room for additional status or handshake inputs, and the four driver channels can handle outbound data and control signals. Its single 5 V architecture simplifies power distribution around instrumentation that often lacks bipolar analog supplies.
Test and Measurement Instrument
A bench instrument using the ADM241LAR can add an RS-232 command and control interface without building a separate driver-receiver subsystem. The 28-pin SOIC package supports conventional surface-mount assembly, and approximately ±9 V generated output swing meets the needs of a standard RS-232 link. Designers should use the manufacturer’s recommended charge-pump layout and verify timing margins because instrument-control traffic can include both continuous data and hardware handshakes.
Point-of-Sale Terminal
The ADM241LAR is appropriate for point-of-sale equipment that must connect a peripheral through RS-232 while the main electronics use a single 5 V supply. Four drivers and five receivers can support data transmission, receipt information, and hardware-control inputs in one integrated interface. The low-power shutdown mode can reduce consumption when the port is idle, but the system must preserve any required receive-active behavior and observe the exact shutdown truth table.
Barcode Scanner Interface
A barcode-scanner interface can use the ADM241LAR to connect equipment operating from 5 V to a scanner or peripheral that expects bipolar RS-232 signaling. The integrated converters generate approximately ±9 V without requiring a separate negative supply rail, and the receiver input tolerance of ±30 V provides margin for commonly exposed connector wiring. In installations with long cables or noisy machinery, add suitable connector protection and validate the signal at the intended baud rate.
Embedded Control Communication
The ADM241LAR supports legacy RS-232 service ports on embedded controllers that use a 5 V core supply. Its five receivers can connect several incoming control or status signals, and the low-power shutdown current of no more than 1 µA helps conserve power during inactive periods. The final design must account for ground potential differences, connector protection, and the transition between logic-level controller pins and bipolar line-side signals.
工程參考資料,適用於 ADM241LAR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Package | 28-pin SOIC |
| Brand | Analog Devices |
| Supply Voltage | 5 V |
| Driver Channels | 4 |
| Receiver Channels | 5 |
| Maximum Data Rate | 120 kbps |
| Driver Output Swing | Approximately ±9 V |
| Charge-Pump Capacitor Value | 1 µF |
| Shutdown Supply Current | ≤1 µA |
| Receiver Input Voltage Tolerance | ±30 V |
| Interface Standards | EIA-232-E and V.28 |
| Mounting Type | Surface Mount |
主要差異化特點
- Four transmitters and five receivers in one interface (對比A typical four-driver/four-receiver RS-232 transceiver)
- Single-supply operation with integrated bipolar generation (對比A discrete RS-232 driver and receiver design)
- Low-power shutdown suitable for managed interfaces (對比A continuously powered discrete RS-232 interface)
設計說明
Place the specified 1 µF charge-pump capacitors close to their associated ADM241LAR pins, following the Analog Devices datasheet layout example. Keep these high-current charge-pump paths compact and away from sensitive receiver inputs. Accurate placement reduces switching disturbances on the board, while the 28-pin SOIC footprint simplifies routing compared with a fine-pitch package.
Connect the ADM241LAR to a properly decoupled 5 V rail and follow the manufacturer’s recommended bypass arrangement. Because the receiver channels can accept signals up to ±30 V, the power and ground structure must remain stable when connector-side transients occur. Add connector protection separately if the installation exposes the RS-232 port to severe industrial surges.
Separate logic-side nets from connector-side driver and receiver nets to prevent charge-pump and external line activity from coupling into sensitive logic. Maintain a direct return path between interface ground and the connected equipment, and route the RS-232 cable away from switching nodes and high-current traces. Validate the completed interface at the highest intended data rate.
Do not treat the approximately ±9 V generated swing as permission to exceed the receiver’s ±30 V input rating. Confirm the shutdown truth table before using the low-power mode, especially when a system expects a receiver to remain active during transmitter shutdown. Also verify package pin functions rather than assuming that every equivalent-ordering code preserves the same pinout.
合規資訊
EIA-232-E and V.28 interface compliance is stated in the Analog Devices datasheet. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from current manufacturer documentation.