ADS7810U-1 - 12-Bit 800 kHz SAR ADC | Texas Instruments
MPN: ADS7810U-1 ✓ 啟用中ADS7810U-1 概覽
An analog-to-digital converter is an interface IC that converts a continuously varying analog voltage into a numerical representation for processing, measurement, or control. The ADS7810U-1 belongs to the SAR ADC hierarchy, where an internal sample-and-hold circuit and successive-approximation conversion process one analog sample at a time. This architecture is appropriate for industrial instrumentation, data acquisition, and embedded control systems where a parallel interface provides straightforward connection to digital processors.
The principal specifications are 12-bit resolution, an 800 kS/s maximum sampling rate, one single-ended input, and a 28-pin SOIC package. The converter uses a 5 V digital supply and a ±5 V analog supply. Its specified operating temperature range is -40 °C to +70 °C. The parallel output supports direct access to conversion results without requiring a serial data link.
Internally, the ADS7810 is described as a complete CMOS sampling converter containing a 12-bit capacitor-based SAR ADC, inherent sample-and-hold circuitry, a reference, a clock, and a microprocessor interface. The capacitor-based conversion core repeatedly resolves the input against internal charge redistribution. The parallel interface then presents the completed 12-bit result for acquisition by an external processor or latch.
Typical applications include industrial process measurement, laboratory instrumentation, digital panel meters, closed-loop control, data-acquisition equipment, and embedded systems that sample bipolar analog signals. Its 800 kS/s conversion capability provides a practical balance between acquisition speed, interface simplicity, and analog measurement resolution.
PCB design should preserve short, controlled analog-input traces and provide stable supply bypassing near the device. Because the converter uses parallel outputs, data-bus timing and output settling should be checked against the acquisition system’s clock requirements. The 28-pin SOIC footprint also requires enough spacing around the device for routing all address, control, data, analog, and supply connections.
This page combines the core ADS7810U-1 specifications with application guidance, design notes, comparison data, and verified drop-in alternatives. It is intended to help engineers identify the correct ADC replacement while accounting for package compatibility, resolution, conversion rate, interface type, and supply requirements.
直接替換替代品,適用於 ADS7810U-1 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ADS7810U-1 (相同外形與佔位) — 差異在於 Package, Architecture, Sampling Rate, Resolution, Analog Supply Voltage.
ADS7810U/1KG4
✅ 直接替換聯絡詢價
查看資料表 →ADS7810U/1KE4
✅ 直接替換📋 參考替代品(不在目錄中)
ADS7810UB/1KE4
✅ 直接替換📋 參考替代品(不在目錄中)
ADS7810U-1 最大額定值與電氣特性
| 解析度 | 12 bit |
| Maximum Sampling Rate | 800 kS/s |
| Number of Input Channels | 1 channel |
| Conversion Architecture | Successive-approximation register (SAR) |
| Analog Input Type | Single-ended |
| Data Interface | Parallel |
| Analog Supply Voltage | ±5 V |
| Digital Supply Voltage | 5 V |
| 工作溫度範圍 | -40 °C to +70 °C |
| 封裝 | 28-pin SOIC |
| Total Pin Count | 28 pins |
| 安裝類型 | Surface mount |
| Process Technology | CMOS |
| Temperature Grade | Industrial |
| Internal Sample-and-Hold | Yes |
| Internal Reference | Yes |
ADS7810U-1 28-pin soic 腳位配置指南
ADS7810U-1(28-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: ADS7810U-1.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADS7810U-1 適用於 6 應用s: Industrial Process Measurement, Laboratory Data Acquisition, Digital Panel Meter, Closed-Loop Control System, Power Supply Monitoring, Embedded Sensor Interface.
Industrial Process Measurement
The ADS7810U-1 fits industrial process measurement when a sensor or transducer produces a conditioned, single-ended analog signal that must be sampled by an embedded controller. Its 12-bit resolution provides 4096 digital codes, while the 800 kS/s maximum sampling rate supports rapid acquisition of changing process values. The parallel interface exposes conversion results directly to a processor or acquisition latch. Use the ±5 V analog supply for compatible bipolar front-end circuitry and isolate the 5 V digital side according to the manufacturer’s grounding guidance. Conversion timing, input settling, and simultaneous sampling requirements should be checked before choosing this ADC for a particular loop.
推薦
Laboratory Data Acquisition
The ADS7810U-1 is appropriate for laboratory data-acquisition equipment that must capture a conditioned analog waveform or sensor output at up to 800 kS/s. Its 12-bit SAR architecture provides a practical resolution-versus-speed balance, while the parallel output interface simplifies connection to digital acquisition logic. The ±5 V analog supply supports bipolar measurement front ends, and the 5 V digital supply aligns with conventional laboratory-control logic. For high-accuracy measurements, evaluate reference quality, input bandwidth, settling time, noise performance, and the acquisition system’s clock relationship using the manufacturer datasheet.
推薦
Digital Panel Meter
The ADS7810U-1 can serve as the acquisition element in a digital panel meter measuring pressure, temperature, position, or another slowly changing analog quantity. The 12-bit conversion resolution offers a useful display range, and the 800 kS/s capability permits repeated measurements or filtering without requiring a high-speed serial ADC. Its 28-pin SOIC package is practical for a mixed analog and digital measurement board. Keep the sensor signal path short, reference the converter according to the datasheet, and select averaging or digital filtering to balance display stability against response time.
推薦
Closed-Loop Control System
The ADS7810U-1 is suitable for closed-loop control applications that require frequent feedback measurements from an analog command or sensor signal. A maximum conversion rate of 800 kS/s allows the control processor to obtain new 12-bit measurements rapidly, while the parallel interface supports deterministic data capture. The converter must operate within its input, reference, and supply limits, and the analog signal must settle properly before each conversion. Validate loop latency, processor bus timing, scaling, and saturation behavior in the target controller before relying on the nominal sampling rate for control-loop timing.
推薦
Power Supply Monitoring
The ADS7810U-1 can monitor a scaled power-supply voltage in laboratory, industrial, or service equipment when the measured level is conditioned into the converter’s permitted analog range. Its 12-bit resolution can distinguish 4096 levels over the full conversion range, making it useful for supervision functions that need more detail than a simple comparator. The 800 kS/s conversion capability supports trend acquisition and fault analysis. Designers should account for divider accuracy, input impedance, reference stability, isolation, and the requirement that the monitored signal remain within the ADC input limits.
推薦
Embedded Sensor Interface
The ADS7810U-1 can serve as the analog front end for an embedded sensor node that converts a conditioned sensor voltage into a 12-bit digital measurement. Its single-ended input and parallel interface are straightforward for a processor with dedicated or multiplexed digital I/O, while the 800 kS/s rate provides headroom for periodic sampling and calibration routines. Use suitable analog conditioning for sensor excitation, filtering, gain, and level shifting. Because the converter is designed for a ±5 V analog supply and 5 V digital supply, verify compatibility with the sensor subsystem and processor voltage levels.
推薦
推薦產品摘要
工程參考資料,適用於 ADS7810U-1 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADS7810U/1K | ADS7810U/1KE4 | ADS7810UB/1KE4 | ADS7810UB | ADS7819UB |
|---|---|---|---|---|---|---|
| Package | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Maximum Sampling Rate | 800 kS/s | 800 kS/s | 800 kS/s | 800 kS/s | 800 kS/s | 800 kS/s |
| Conversion Architecture | SAR | SAR | SAR | SAR | SAR | SAR |
| Input Configuration | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended |
| Data Interface | Parallel | Parallel | Parallel | Parallel | Parallel | Parallel |
| Operating Temperature Range | -40 °C to +70 °C | -40 °C to +70 °C | -40 °C to +70 °C | -40 °C to +70 °C | -40 °C to +70 °C | -40 °C to +70 °C |
| Special Features | Internal reference and inherent sample-and-hold | Internal reference and inherent sample-and-hold | Internal reference and inherent sample-and-hold | Consistent ADS7810-family functionality | Consistent ADS7810-family functionality | Principal performance characteristics stated as consistent |
主要差異化特點
- Exact original-family identity for controlled replacements (對比ADS7819UB)
- 800 kS/s conversion rate matches the listed ADS7810-family alternatives (對比ADS7810U/1KE4)
- Pin-compatible family alternatives preserve the 28-pin SOIC footprint (對比ADS7810UB/1KE4)
設計說明
Route the analog input directly to the converter and keep it away from parallel data lines, clock signals, and switching supply nodes. Place the manufacturer-specified input and reference bypass capacitors close to their associated pins. The ADS7810U-1 combines a ±5 V analog supply with a 5 V digital supply, so separating analog and digital current paths is essential for preventing digital switching activity from appearing as conversion noise.
Treat each parallel output as a synchronous signal and verify setup and hold timing at the receiving logic. The 28-pin package exposes multiple address, control, and data lines, so mismatched trace lengths or poorly terminated clock routes can reduce timing margin. Use the manufacturer’s acquisition timing diagram as the basis for processor read timing, and avoid introducing unnecessary loads on the output bus.
Provide independent, low-impedance paths for the ±5 V analog supply and 5 V digital supply. Check return-current paths so output-current activity in the digital section does not share sensitive analog-ground segments. If the analog source has a large DC offset, confirm that it remains inside the converter’s allowed input range relative to the reference and supply arrangement before layout release.
Do not select a related ADS7810 suffix solely because it has the same resolution, sampling rate, and 28-pin SOIC outline. Verify the exact pin names, input and reference behavior, acquisition timing, temperature grade, and manufacturer ordering code for the assembled board. Also confirm the production packing form and reel orientation before authorizing a substitute for ADS7810U-1.
合規資訊
The ADS7810U-1 is an industrial-temperature analog-to-digital converter. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was established for the exact ordering code, and automotive qualification is not indicated.