ADS7810U-1 - 12-Bit 800 kHz SAR ADC | Texas Instruments
料号: ADS7810U-1 ✓ 量产中ADS7810U-1 概述
An analog-to-digital converter is an interface IC that converts a continuously varying analog voltage into a numerical representation for processing, measurement, or control. The ADS7810U-1 belongs to the SAR ADC hierarchy, where an internal sample-and-hold circuit and successive-approximation conversion process one analog sample at a time. This architecture is appropriate for industrial instrumentation, data acquisition, and embedded control systems where a parallel interface provides straightforward connection to digital processors.
The principal specifications are 12-bit resolution, an 800 kS/s maximum sampling rate, one single-ended input, and a 28-pin SOIC package. The converter uses a 5 V digital supply and a ±5 V analog supply. Its specified operating temperature range is -40 °C to +70 °C. The parallel output supports direct access to conversion results without requiring a serial data link.
Internally, the ADS7810 is described as a complete CMOS sampling converter containing a 12-bit capacitor-based SAR ADC, inherent sample-and-hold circuitry, a reference, a clock, and a microprocessor interface. The capacitor-based conversion core repeatedly resolves the input against internal charge redistribution. The parallel interface then presents the completed 12-bit result for acquisition by an external processor or latch.
Typical applications include industrial process measurement, laboratory instrumentation, digital panel meters, closed-loop control, data-acquisition equipment, and embedded systems that sample bipolar analog signals. Its 800 kS/s conversion capability provides a practical balance between acquisition speed, interface simplicity, and analog measurement resolution.
PCB design should preserve short, controlled analog-input traces and provide stable supply bypassing near the device. Because the converter uses parallel outputs, data-bus timing and output settling should be checked against the acquisition system’s clock requirements. The 28-pin SOIC footprint also requires enough spacing around the device for routing all address, control, data, analog, and supply connections.
This page combines the core ADS7810U-1 specifications with application guidance, design notes, comparison data, and verified drop-in alternatives. It is intended to help engineers identify the correct ADC replacement while accounting for package compatibility, resolution, conversion rate, interface type, and supply requirements.
直接替换替代料: ADS7810U-1 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADS7810U-1 (相同外形与封装尺寸) ——差异在于 Package, Architecture, Sampling Rate, Resolution, Analog Supply Voltage.
ADS7810U/1KG4
✅ 直接替换联系询价
查看数据手册 →ADS7810U/1KE4
✅ 直接替换📋 参考替代料(不在目录中)
ADS7810UB/1KE4
✅ 直接替换📋 参考替代料(不在目录中)
ADS7810U-1 最大额定值与电气特性
| 分辨率 | 12 bit |
| Maximum Sampling Rate | 800 kS/s |
| Number of Input Channels | 1 channel |
| Conversion Architecture | Successive-approximation register (SAR) |
| Analog Input Type | Single-ended |
| Data Interface | Parallel |
| Analog Supply Voltage | ±5 V |
| Digital Supply Voltage | 5 V |
| 工作温度范围 | -40 °C to +70 °C |
| 封装 | 28-pin SOIC |
| Total Pin Count | 28 pins |
| 安装类型 | Surface mount |
| Process Technology | CMOS |
| Temperature Grade | Industrial |
| Internal Sample-and-Hold | Yes |
| Internal Reference | Yes |
ADS7810U-1 28-pin soic 引脚配置指南
ADS7810U-1(28-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: ADS7810U-1.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADS7810U-1 适用于 6 应用s: Industrial Process Measurement, Laboratory Data Acquisition, Digital Panel Meter, Closed-Loop Control System, Power Supply Monitoring, Embedded Sensor Interface.
Industrial Process Measurement
The ADS7810U-1 fits industrial process measurement when a sensor or transducer produces a conditioned, single-ended analog signal that must be sampled by an embedded controller. Its 12-bit resolution provides 4096 digital codes, while the 800 kS/s maximum sampling rate supports rapid acquisition of changing process values. The parallel interface exposes conversion results directly to a processor or acquisition latch. Use the ±5 V analog supply for compatible bipolar front-end circuitry and isolate the 5 V digital side according to the manufacturer’s grounding guidance. Conversion timing, input settling, and simultaneous sampling requirements should be checked before choosing this ADC for a particular loop.
推荐
Laboratory Data Acquisition
The ADS7810U-1 is appropriate for laboratory data-acquisition equipment that must capture a conditioned analog waveform or sensor output at up to 800 kS/s. Its 12-bit SAR architecture provides a practical resolution-versus-speed balance, while the parallel output interface simplifies connection to digital acquisition logic. The ±5 V analog supply supports bipolar measurement front ends, and the 5 V digital supply aligns with conventional laboratory-control logic. For high-accuracy measurements, evaluate reference quality, input bandwidth, settling time, noise performance, and the acquisition system’s clock relationship using the manufacturer datasheet.
推荐
Digital Panel Meter
The ADS7810U-1 can serve as the acquisition element in a digital panel meter measuring pressure, temperature, position, or another slowly changing analog quantity. The 12-bit conversion resolution offers a useful display range, and the 800 kS/s capability permits repeated measurements or filtering without requiring a high-speed serial ADC. Its 28-pin SOIC package is practical for a mixed analog and digital measurement board. Keep the sensor signal path short, reference the converter according to the datasheet, and select averaging or digital filtering to balance display stability against response time.
推荐
Closed-Loop Control System
The ADS7810U-1 is suitable for closed-loop control applications that require frequent feedback measurements from an analog command or sensor signal. A maximum conversion rate of 800 kS/s allows the control processor to obtain new 12-bit measurements rapidly, while the parallel interface supports deterministic data capture. The converter must operate within its input, reference, and supply limits, and the analog signal must settle properly before each conversion. Validate loop latency, processor bus timing, scaling, and saturation behavior in the target controller before relying on the nominal sampling rate for control-loop timing.
推荐
Power Supply Monitoring
The ADS7810U-1 can monitor a scaled power-supply voltage in laboratory, industrial, or service equipment when the measured level is conditioned into the converter’s permitted analog range. Its 12-bit resolution can distinguish 4096 levels over the full conversion range, making it useful for supervision functions that need more detail than a simple comparator. The 800 kS/s conversion capability supports trend acquisition and fault analysis. Designers should account for divider accuracy, input impedance, reference stability, isolation, and the requirement that the monitored signal remain within the ADC input limits.
推荐
Embedded Sensor Interface
The ADS7810U-1 can serve as the analog front end for an embedded sensor node that converts a conditioned sensor voltage into a 12-bit digital measurement. Its single-ended input and parallel interface are straightforward for a processor with dedicated or multiplexed digital I/O, while the 800 kS/s rate provides headroom for periodic sampling and calibration routines. Use suitable analog conditioning for sensor excitation, filtering, gain, and level shifting. Because the converter is designed for a ±5 V analog supply and 5 V digital supply, verify compatibility with the sensor subsystem and processor voltage levels.
推荐
推荐产品汇总
工程参考数据: ADS7810U-1 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADS7810U/1K | ADS7810U/1KE4 | ADS7810UB/1KE4 | ADS7810UB | ADS7819UB |
|---|---|---|---|---|---|---|
| Package | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Maximum Sampling Rate | 800 kS/s | 800 kS/s | 800 kS/s | 800 kS/s | 800 kS/s | 800 kS/s |
| Conversion Architecture | SAR | SAR | SAR | SAR | SAR | SAR |
| Input Configuration | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended |
| Data Interface | Parallel | Parallel | Parallel | Parallel | Parallel | Parallel |
| Operating Temperature Range | -40 °C to +70 °C | -40 °C to +70 °C | -40 °C to +70 °C | -40 °C to +70 °C | -40 °C to +70 °C | -40 °C to +70 °C |
| Special Features | Internal reference and inherent sample-and-hold | Internal reference and inherent sample-and-hold | Internal reference and inherent sample-and-hold | Consistent ADS7810-family functionality | Consistent ADS7810-family functionality | Principal performance characteristics stated as consistent |
关键差异点
- Exact original-family identity for controlled replacements (对比 ADS7819UB)
- 800 kS/s conversion rate matches the listed ADS7810-family alternatives (对比 ADS7810U/1KE4)
- Pin-compatible family alternatives preserve the 28-pin SOIC footprint (对比 ADS7810UB/1KE4)
设计说明
Route the analog input directly to the converter and keep it away from parallel data lines, clock signals, and switching supply nodes. Place the manufacturer-specified input and reference bypass capacitors close to their associated pins. The ADS7810U-1 combines a ±5 V analog supply with a 5 V digital supply, so separating analog and digital current paths is essential for preventing digital switching activity from appearing as conversion noise.
Treat each parallel output as a synchronous signal and verify setup and hold timing at the receiving logic. The 28-pin package exposes multiple address, control, and data lines, so mismatched trace lengths or poorly terminated clock routes can reduce timing margin. Use the manufacturer’s acquisition timing diagram as the basis for processor read timing, and avoid introducing unnecessary loads on the output bus.
Provide independent, low-impedance paths for the ±5 V analog supply and 5 V digital supply. Check return-current paths so output-current activity in the digital section does not share sensitive analog-ground segments. If the analog source has a large DC offset, confirm that it remains inside the converter’s allowed input range relative to the reference and supply arrangement before layout release.
Do not select a related ADS7810 suffix solely because it has the same resolution, sampling rate, and 28-pin SOIC outline. Verify the exact pin names, input and reference behavior, acquisition timing, temperature grade, and manufacturer ordering code for the assembled board. Also confirm the production packing form and reel orientation before authorizing a substitute for ADS7810U-1.
合规信息
The ADS7810U-1 is an industrial-temperature analog-to-digital converter. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was established for the exact ordering code, and automotive qualification is not indicated.