APA075-TQ100I - 75K Gate FPGA | Microchip Technology
MPN: APA075-TQ100I ✓ 啟用中APA075-TQ100I 概覽
A field-programmable gate array, or FPGA, is a programmable digital logic device within the broader semiconductor and logic IC hierarchy. Instead of implementing every function with permanently wired logic, an FPGA uses configurable digital structures and I/O blocks to implement control, data processing, interface, and embedded-system functions. The APA075 family combines the flexibility of programmable logic with an ASIC-oriented development flow and nonvolatile configuration storage.
The principal specifications identify a 75,000-system-gate device with 3,072 programmable cells, 27,648 RAM bits, and 66 I/O. Its maximum stated operating frequency is 180 MHz. The 100-LQFP package provides a compact surface-mount option with 0.5 mm pitch, while the 100-TQFP package description used by some catalog listings identifies the same 100-pin physical format for this family.
ProASICPLUS architecture is based on nonvolatile flash technology rather than a volatile configuration memory. Flash configuration supports reprogramming and live-at-power-up operation, so a programmed design does not depend on an external configuration PROM during normal startup. The available family information also identifies the technology as CMOS and confirms RoHS compliance, supporting use in industrial, communications, embedded-control, and ASIC-prototyping designs.
Typical applications include industrial control logic, protocol bridges, data-acquisition front ends, embedded instrumentation, communications equipment, and general-purpose digital prototyping. The combination of 66 I/O and 27,648 RAM bits is useful when a design must connect multiple external buses, capture parallel data, or combine state logic with moderate on-chip buffering. Its nonvolatile, live-at-power-up behavior simplifies deployments where deterministic startup and field reconfiguration are important.
PCB design should follow the 100-pin LQFP land pattern and all recommended power, ground, and decoupling connections shown in the manufacturer documentation. Because the device is a programmable logic platform rather than a fixed-function ASIC, timing closure also depends on the selected pin assignments, logic mapping, clocking scheme, and I/O standards. Validate the complete design against the applicable voltage, temperature, timing, and power constraints for the selected system configuration.
This product page combines device specifications, same-footprint alternatives, application guidance, and design-oriented comparison information to support FPGA selection and PCB reuse without relying on the manufacturer datasheet alone.
直接替換替代品,適用於 APA075-TQ100I — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: APA075-TQ100I (相同外形與佔位) — 差異在於 Package, RoHS Status.
APA075-TQG100I
✅ 直接替換📋 參考替代品(不在目錄中)
APA075-TQ100
✅ 直接替換聯絡詢價
查看資料表 →APA075-TQG100
✅ 直接替換📋 參考替代品(不在目錄中)
APA075-TQ100I 最大額定值與電氣特性
| FPGA Family | ProASICPLUS |
| System Gates | 75,000 gates |
| Logic Cells | 3,072 cells |
| Maximum Frequency | 180 MHz |
| Total RAM Bits | 27,648 bits |
| Number of I/O | 66 I/O |
| 封裝 | 100-LQFP / 100-TQFP |
| Package Pin Count | 100 pins |
| Package Pitch | 0.5 mm |
| 安裝類型 | Surface mount |
| Process Technology | CMOS |
| Configuration Memory | Nonvolatile flash |
| Reprogrammable | Yes |
| Power-Up Behavior | Live at power-up |
| RoHS 狀態 | Compliant |
APA075-TQ100I 0.5 mm 腳位配置指南
APA075-TQ100I(0.5 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: APA075-TQ100I.
請參閱 資料表 以查看完整腳位配置。
典型應用
APA075-TQ100I 適用於 6 應用s: Industrial Control Logic, Protocol and Interface Bridging, Data-Acquisition Front Ends, Embedded Communication Equipment, ASIC Prototyping and Bring-Up, Programmable Signal Conditioning.
Industrial Control Logic
The APA075-TQ100I fits industrial controllers that combine sequential control, parallel data handling, and multiple external interfaces. Its 3,072 logic cells and 27,648 RAM bits provide resources for state machines, counters, data buffers, and communication logic, while 66 I/O leave substantial connectivity for sensors, actuators, human-interface circuits, and field buses. The 100-LQFP package reduces board area without requiring a high-pin-count BGA layout. Nonvolatile flash configuration and live-at-power-up behavior are particularly useful when equipment must restart deterministically and support field reprogramming. The 180 MHz maximum frequency also allows clocked control or interface logic, although timing closure depends on the actual design and I/O assignment.
推薦
Protocol and Interface Bridging
The APA075-TQ100I can serve as a configurable interface bridge between systems using incompatible bus widths, timing, or signal formats. With 66 I/O, a design can distribute signals among parallel data channels, control lines, clocks, and handshake signals, while 27,648 RAM bits support buffering and temporary data storage. The 3,072-cell implementation can hold finite-state machines for serialization, framing, protocol conversion, and fault handling. Its live-at-power-up configuration removes the need for a separate configuration PROM in normal operation, and reprogrammability supports field adaptation when bridge requirements evolve. Actual signal rates must be validated against the 180 MHz device limit and the selected I/O standards.
推薦
Data-Acquisition Front Ends
The APA075-TQ100I is suitable for data-acquisition and instrumentation designs that must collect parallel samples, perform digital filtering, and transfer information to a processor or communications module. Its 66 I/O can accommodate multiple sensor channels, control outputs, clocks, and status signals, while 27,648 RAM bits provide useful on-chip buffering for sampled data and timing histories. The 3,072 programmable cells can implement acquisition state machines, calibration logic, trigger handling, and filtering functions. Live-at-power-up operation supports repeatable initialization, while flash-based configuration permits design updates without volatile setup. Timing-sensitive analog interfaces still require careful pin assignment, clock planning, and board-level signal-integrity work.
推薦
Embedded Communication Equipment
The APA075-TQ100I can be used in communications equipment for packet framing, channel control, status monitoring, and protocol adaptation. Its 75,000 system gates and 3,072 logic cells accommodate parallel-to-serial conversion, CRC processing, command decoding, and supervisory state machines. A total of 27,648 RAM bits can support frame buffers, counters, and temporary payload storage, while 66 I/O provide connectivity to transceivers, memory devices, and control peripherals. Nonvolatile configuration allows the equipment to retain its programmed behavior across power cycles and enables controlled field updates. Engineers should verify the selected suffix against environmental requirements and confirm achievable timing for the target communication rate.
推薦
ASIC Prototyping and Bring-Up
The APA075-TQ100I is useful for prototyping programmable logic intended for a later ASIC implementation because it supports reprogrammable designs and live-at-power-up configuration. Designers can implement control blocks, datapaths, bus interfaces, and test logic before committing the design to mask-based silicon. The 3,072-cell capacity and 27,648 RAM bits provide enough resources for medium-scale functional prototypes, while 66 I/O expose a substantial number of external test and system signals. Flash-based configuration makes it practical to retain multiple design revisions and reproduce a known operating state at power-up. Production migration still requires formal equivalence checking and verification against the final ASIC specification.
推薦
Programmable Signal Conditioning
The APA075-TQ100I can implement programmable signal-conditioning and digital-assist functions between sensors, converters, and a host processor. Its 66 I/O support parallel sensor inputs, threshold controls, calibration registers, and digital signaling, while 27,648 RAM bits accommodate sample histories and intermediate calculations. The 3,072 logic cells can be used for programmable gain sequencing, filtering, interpolation, diagnostics, and fault-safe output control. Because the FPGA starts live with its stored flash configuration, a completed instrument can power up in a defined condition without an external loader. The final implementation must include timing analysis, I/O-standard compatibility, and recovery behavior for invalid or out-of-range sensor data.
推薦
推薦產品摘要
工程參考資料,適用於 APA075-TQ100I — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | APA075-TQG100I | APA075-TQ100 | APA075-TQG100 |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-LQFP (PQFP/TQFP-100) | 100-LQFP (PQFP/TQFP-100) | 100-LQFP (PQFP/TQFP-100) | 100-LQFP (PQFP/TQFP-100) |
| FPGA Family | ProASICPLUS | ProASICPLUS | ProASICPLUS | ProASICPLUS |
| System Gates | 75,000 gates | 75,000 gates | 75,000 gates | 75,000 gates |
| Configuration Memory | Nonvolatile flash | Nonvolatile flash | Nonvolatile flash | Nonvolatile flash |
| Power-Up Behavior | Live at power-up | Live at power-up | Live at power-up | Live at power-up |
主要差異化特點
- Closest documented same-footprint alternative retains the principal logic resources (對比APA075-TQG100I)
- Same-package family alternative preserves the complete stated resource configuration (對比APA075-TQ100)
- Flash-based live-at-power-up behavior supports autonomous startup (對比APA075-TQG100)
設計說明
Use the manufacturer 100-LQFP land pattern and pin-assignment table when routing APA075-TQ100I. The package has 0.5 mm pitch, so verify pad length, pad width, solder-mask opening, and courtyard clearance against the current package drawing. Place decoupling capacitors close to the appropriate power pins and provide the required ground return path with minimal loop area. Keep configuration or programming access unobstructed if the assembled board requires field updates.
Confirm the selected APA075-TQ100I suffix against the system’s supply voltage, I/O voltage, operating-temperature, and speed requirements before schematic release. The device combines 75,000 system gates, 27,648 RAM bits, and up to 180 MHz operation, so actual power consumption depends on the implemented logic, clock activity, I/O loading, and supply voltage. Use Microchip’s power-estimation workflow with the final constraints rather than assigning a fixed current requirement to the FPGA.
Create a complete pin plan before routing clocks, high-speed buses, and configuration signals. Record each I/O standard, direction, intended clock domain, and permitted voltage in the design constraints. Keep clocks away from noisy switching nodes, use short return paths for ground, and follow the recommended input and output circuit recommendations in the manufacturer documentation. Because APA075-TQ100I is programmable, timing failures can often be resolved through legal pin reassignment before physical layout changes become necessary.
Do not treat a shared 100-LQFP package as sufficient proof that every APA075 suffix is interchangeable. Confirm temperature grade, speed grade, electrical limits, configuration method, and lifecycle status for the exact orderable MPN. The I suffix identifies a distinct ordering option, and related TQ, TQG, and TQ100 variants may serve different application or procurement requirements. Record the manufacturer part number on documentation, BOMs, and test fixtures to prevent substitution errors.
合規資訊
RoHS compliance is stated in the APA075 family comparison information. No specific automotive qualification, REACH status, lead-free declaration, halogen-free declaration, or conflict-minerals statement was identified.