ATF16V8BQL-25PC - 25ns Low-Power 8-Macrocell EE PLD | Microchip
MPN: ATF16V8BQL-25PC ✗ 停產ATF16V8BQL-25PC 概覽
An electrically erasable PLD is a user-programmable logic semiconductor that stores its configuration in nonvolatile EEPROM rather than in external switches or mask-programmed logic. The ATF16V8B family provides a superset of the generic 16R8 architecture and can directly replace many 20-pin combinatorial PLDs. Each of its eight outputs is allocated eight product terms, allowing moderately complex sum-of-products logic to be implemented in one package.
The ATF16V8BQL emphasizes low standby power through Input Transition Detection. According to the manufacturer datasheet, its typical standby current is 5 mA, and the device automatically enters its low-power mode when inputs are idle. A 25 ns speed grade supports moderate clock and control-logic requirements, while electrically erasable configuration permits reprogramming without replacing the device.
The device offers three operating modes configured automatically by software: registered, complex combinatorial, and simple combinatorial. These modes support output-register feedback, exclusive-OR structures, and conventional combinational equations. The architecture emulates the industry-standard 20-pin PAL arrangement and provides eight outputs with up to eight product terms per output.
Typical uses include industrial control decoding, legacy peripheral interface logic, address or command translation, and small glue-logic blocks in test, communications, and embedded equipment. ATF16V8BQL-25PC is especially useful when low quiescent consumption is more important than the shortest available propagation delay and a through-hole package is acceptable.
Designers should assign each PLD pin according to the manufacturer pin-description table, provide a stable 5 V supply, and include the required decoupling capacitor close to the supply pins. Legacy PLD designs should also be checked for signal polarity, output enable behavior, unused-pin treatment, and timing margins before production release.
This product record combines the manufacturer's electrical and architectural details with package-specific sourcing guidance, programming considerations, practical design notes, and a careful assessment of drop-in replacement options for the ATF16V8BQL-25PC.
直接替換替代品,適用於 ATF16V8BQL-25PC — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
ATF16V8B-25PC
✅ 直接替換📋 參考替代品(不在目錄中)
ATF16V8BQL-25PC 最大額定值與電氣特性
| Device Type | Electrically Erasable Programmable Logic Device |
| Architecture | 16V8 with 8 macrocells |
| Number of Macrocells | 8 |
| Maximum Inputs | 16 inputs |
| Number of I/O Outputs | 8 I/O |
| Product Terms per Output | 8 product terms |
| 供應電壓 | 5 V |
| Propagation Delay | 25 ns |
| Standby Current | 5 mA typical |
| Configuration Technology | Electrically Erasable Flash memory |
| Power-Down Feature | Automatic low-power mode through Input Transition Detection |
| Operating Modes | Registered, complex combinatorial, and simple combinatorial |
| 封裝 | 20-PDIP |
| 安裝類型 | Through-hole |
| Logic Family | CMOS electrically erasable PLD |
| Equivalent Gate Count | 250 gates |
| Power Class | Quarter and low power |
ATF16V8BQL-25PC 腳位配置
| 腳位 1 | CLK — Clock input |
| 腳位 2 | I/O0 — Configurable input or output |
| 腳位 3 | I/O1 — Configurable input or output |
| 腳位 4 | I/O2 — Configurable input or output |
| 腳位 5 | I/O3 — Configurable input or output |
| 腳位 6 | I/O4 — Configurable input or output |
| 腳位 7 | I/O5 — Configurable input or output |
| 腳位 8 | I/O6 — Configurable input or output |
| 腳位 9 | I/O7 — Configurable input or output |
| 腳位 10 | GND — Ground |
| 腳位 11 | GND — Ground |
| 腳位 12 | /OE — Active-low output enable |
| 腳位 13 | I/O7 — Configurable input or output |
| 腳位 14 | I/O6 — Configurable input or output |
| 腳位 15 | I/O5 — Configurable input or output |
| 腳位 16 | I/O4 — Configurable input or output |
| 腳位 17 | I/O3 — Configurable input or output |
| 腳位 18 | I/O2 — Configurable input or output |
| 腳位 19 | I/O1 — Configurable input or output |
| 腳位 20 | VCC — Positive supply |
典型應用
ATF16V8BQL-25PC 適用於 6 應用s: Industrial Command Decoding, Legacy Peripheral Interface, Address and Command Translation, Test Equipment Control Logic, Low-Power Embedded Glue Logic, Telecom and Communications Interface.
Industrial Command Decoding
The ATF16V8BQL-25PC fits legacy industrial control boards that decode switches, selectors, and status lines into internal control commands. Eight macrocells, up to 16 inputs, and eight product terms per output provide sufficient capacity for compact sum-of-products decoding, while the 25 ns propagation delay accommodates moderate control-path timing. The 20-PDIP package is straightforward to inspect and replace in through-hole equipment. Its low-power ITD behavior also helps when logic sections remain idle for long periods, although the complete operating-current budget and any required temperature range must be checked against the equipment specification.
推薦
Legacy Peripheral Interface
The ATF16V8BQL-25PC can implement protocol adaptation between a host controller and older peripheral equipment by translating control states, generating enables, or combining asynchronous status inputs. Its electrically erasable configuration supports design revisions without changing the PCB, and its 8 I/O outputs provide flexible use as inputs or outputs. The 25 ns device can bridge many control and handshake signals without excessive propagation delay. Engineers should verify clock-domain relationships, output-enable polarity, and unused input states in the manufacturer datasheet, particularly when adapting the design to a faster host bus.
推薦
Address and Command Translation
The ATF16V8BQL-25PC is suitable for compact address or command translation between incompatible digital systems. Eight macrocells can hold multiple product-term equations, while the 16V8 organization supports up to 16 inputs and 8 I/O outputs. Electrically erasable Flash technology permits firmware-like logic updates during equipment maintenance, reducing board respin risk. For dependable implementation, validate address overlap, propagate uncertain states through invalid-command outputs, and preserve required setup and hold margins around clocked outputs under the worst-case 25 ns timing scenario.
推薦
Test Equipment Control Logic
The ATF16V8BQL-25PC can consolidate small control functions in legacy test and measurement equipment, such as relay-sequence enable logic, status-latch decoding, or front-panel command gating. The 25 ns propagation delay supports moderate digital control paths, and eight configurable I/O outputs allow the same device to participate in both input decoding and output generation. The through-hole 20-PDIP package also simplifies repair and prototyping. Before integrating it into a measuring chain, keep it out of precision analog paths, provide clean 5 V power, and account for unused-pin and reset-state behavior in the system verification plan.
推薦
Low-Power Embedded Glue Logic
The ATF16V8BQL-25PC fits embedded systems that require a small amount of configurable logic beside a primary controller but value low standby consumption. Input Transition Detection automatically moves the PLD toward its low-power state when inputs are idle, and the manufacturer lists a typical standby current of 5 mA. The electrically erasable architecture allows logic updates without a new package, while the 25 ns speed grade addresses routine handshake and control functions. Designers should confirm whether 5 mA meets the product's sleep-current target and should include programming, configuration-security, and in-field update procedures in the production plan.
推薦
Telecom and Communications Interface
The ATF16V8BQL-25PC can implement auxiliary line-state decoding, enable generation, or alarm masking in legacy telecommunications equipment. The 20-pin PAL-compatible architecture is useful when updating established control boards without changing their through-hole footprint, and the 8-macrocell capacity handles compact multi-signal equations. The 25 ns propagation delay is suitable for many supervisory paths rather than high-speed serial datapaths. Layout should keep the PLD away from switching power stages, use a decoupled 5 V rail, and treat all control outputs as potentially asynchronous until the system specifies safe states for power-up and reset conditions.
推薦
推薦產品摘要
工程參考資料,適用於 ATF16V8BQL-25PC — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ATF16V8B-25PC |
|---|---|---|
| Package | 20-PDIP | 20-PDIP - same |
| Brand | Microchip Technology | Microchip Technology |
| Product Type | Low-power electrically erasable PLD | Standard-power electrically erasable PLD |
| Macrocells | 8 | 8 |
| Maximum Inputs | 16 inputs | 16 inputs |
| I/O Outputs | 8 I/O | 8 I/O |
| Supply Voltage | 5 V | 5 V |
| Propagation Delay | 25 ns | 25 ns |
| Power-Down Feature | Automatic low-power mode through Input Transition Detection | No ATF16V8BQL Input Transition Detection feature |
主要差異化特點
- Lower-power operating variant (對比ATF16V8B-25PC)
- Direct package and timing alignment (對比ATF16V8B-25PC)
- Nonvolatile reprogrammable configuration (對比ATF16V8B-25PC)
設計說明
Use a regulated 5 V rail and place the manufacturer-recommended bypass capacitor immediately between the VCC and GND pins. Keep the supply and return paths short because the 20-PDIP footprint can support long PCB traces if routing is not constrained. In battery-powered equipment, include the 5 mA typical standby current and operating current in the active and idle power budgets before confirming that the low-power variant provides a worthwhile system-level saving.
Do not treat the ATF16V8B and ATF16V8BQL as identical merely because they share the 16V8 architecture and 20-PDIP package. The ATF16V8BQL includes Input Transition Detection and quarter-power characteristics, while the ATF16V8B is the standard-power member. Before substitution, compare the programmed equations, clock behavior, output-enable polarity, unused-pin treatment, AC timing, and power requirements against the manufacturer datasheet.
Reserve the package pin assignments shown in the manufacturer pin-description table and mark all unused inputs so their electrical state is controlled during programming, reset, and power-up. Route the clock with short geometry and maintain separation from switching-regulator and relay-control traces. Although the propagation-delay grade is 25 ns, edge-rate and crosstalk margin cannot be inferred from that figure alone, so validate the completed board with realistic loading and worst-case supply conditions.
The ATF16V8B architecture emulates a 20-pin PAL arrangement, but a generic PAL pinout is not a substitute for the manufacturer package drawing. Verify whether a design requires registered, complex combinatorial, or simple combinatorial behavior because the operating mode is selected automatically by the programming software. Recheck feedback-product-term allocation and clocked-output constraints during compilation rather than relying on a manual equation conversion.
合規資訊
The ATF16V8B family datasheet includes green-package ordering information, but the manufacturer datasheet excerpt does not establish a specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status for this exact legacy MPN.