ATF16V8BQL-25PC - 25ns Low-Power 8-Macrocell EE PLD | Microchip
MPN: ATF16V8BQL-25PC ✗ Cuối đờiATF16V8BQL-25PC Tóm tắt
An electrically erasable PLD is a user-programmable logic semiconductor that stores its configuration in nonvolatile EEPROM rather than in external switches or mask-programmed logic. The ATF16V8B family provides a superset of the generic 16R8 architecture and can directly replace many 20-pin combinatorial PLDs. Each of its eight outputs is allocated eight product terms, allowing moderately complex sum-of-products logic to be implemented in one package.
The ATF16V8BQL emphasizes low standby power through Input Transition Detection. According to the manufacturer datasheet, its typical standby current is 5 mA, and the device automatically enters its low-power mode when inputs are idle. A 25 ns speed grade supports moderate clock and control-logic requirements, while electrically erasable configuration permits reprogramming without replacing the device.
The device offers three operating modes configured automatically by software: registered, complex combinatorial, and simple combinatorial. These modes support output-register feedback, exclusive-OR structures, and conventional combinational equations. The architecture emulates the industry-standard 20-pin PAL arrangement and provides eight outputs with up to eight product terms per output.
Typical uses include industrial control decoding, legacy peripheral interface logic, address or command translation, and small glue-logic blocks in test, communications, and embedded equipment. ATF16V8BQL-25PC is especially useful when low quiescent consumption is more important than the shortest available propagation delay and a through-hole package is acceptable.
Designers should assign each PLD pin according to the manufacturer pin-description table, provide a stable 5 V supply, and include the required decoupling capacitor close to the supply pins. Legacy PLD designs should also be checked for signal polarity, output enable behavior, unused-pin treatment, and timing margins before production release.
This product record combines the manufacturer's electrical and architectural details with package-specific sourcing guidance, programming considerations, practical design notes, and a careful assessment of drop-in replacement options for the ATF16V8BQL-25PC.
Bộ thay thế dễ dàng lắp đặt cho ATF16V8BQL-25PC — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
ATF16V8B-25PC
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATF16V8BQL-25PC Tỷ lệ tối đa & tính chất điện
| Device Type | Electrically Erasable Programmable Logic Device |
| Architecture | 16V8 with 8 macrocells |
| Number of Macrocells | 8 |
| Maximum Inputs | 16 inputs |
| Number of I/O Outputs | 8 I/O |
| Product Terms per Output | 8 product terms |
| Điện áp cung cấp | 5 V |
| Propagation Delay | 25 ns |
| Standby Current | 5 mA typical |
| Configuration Technology | Electrically Erasable Flash memory |
| Power-Down Feature | Automatic low-power mode through Input Transition Detection |
| Operating Modes | Registered, complex combinatorial, and simple combinatorial |
| Hộp | 20-PDIP |
| Kiểu lắp đặt | Through-hole |
| Logic Family | CMOS electrically erasable PLD |
| Equivalent Gate Count | 250 gates |
| Power Class | Quarter and low power |
Cấu hình chân ATF16V8BQL-25PC
| Chân 1 | CLK — Clock input |
| Chân 2 | I/O0 — Configurable input or output |
| Chân 3 | I/O1 — Configurable input or output |
| Chân 4 | I/O2 — Configurable input or output |
| Chân 5 | I/O3 — Configurable input or output |
| Chân 6 | I/O4 — Configurable input or output |
| Chân 7 | I/O5 — Configurable input or output |
| Chân 8 | I/O6 — Configurable input or output |
| Chân 9 | I/O7 — Configurable input or output |
| Chân 10 | GND — Ground |
| Chân 11 | GND — Ground |
| Chân 12 | /OE — Active-low output enable |
| Chân 13 | I/O7 — Configurable input or output |
| Chân 14 | I/O6 — Configurable input or output |
| Chân 15 | I/O5 — Configurable input or output |
| Chân 16 | I/O4 — Configurable input or output |
| Chân 17 | I/O3 — Configurable input or output |
| Chân 18 | I/O2 — Configurable input or output |
| Chân 19 | I/O1 — Configurable input or output |
| Chân 20 | VCC — Positive supply |
Ứng dụng tiêu biểu
ATF16V8BQL-25PC phù hợp cho 6 Áp dụngs: Industrial Command Decoding, Legacy Peripheral Interface, Address and Command Translation, Test Equipment Control Logic, Low-Power Embedded Glue Logic, Telecom and Communications Interface.
Industrial Command Decoding
The ATF16V8BQL-25PC fits legacy industrial control boards that decode switches, selectors, and status lines into internal control commands. Eight macrocells, up to 16 inputs, and eight product terms per output provide sufficient capacity for compact sum-of-products decoding, while the 25 ns propagation delay accommodates moderate control-path timing. The 20-PDIP package is straightforward to inspect and replace in through-hole equipment. Its low-power ITD behavior also helps when logic sections remain idle for long periods, although the complete operating-current budget and any required temperature range must be checked against the equipment specification.
Được đề xuất
Legacy Peripheral Interface
The ATF16V8BQL-25PC can implement protocol adaptation between a host controller and older peripheral equipment by translating control states, generating enables, or combining asynchronous status inputs. Its electrically erasable configuration supports design revisions without changing the PCB, and its 8 I/O outputs provide flexible use as inputs or outputs. The 25 ns device can bridge many control and handshake signals without excessive propagation delay. Engineers should verify clock-domain relationships, output-enable polarity, and unused input states in the manufacturer datasheet, particularly when adapting the design to a faster host bus.
Được đề xuất
Address and Command Translation
The ATF16V8BQL-25PC is suitable for compact address or command translation between incompatible digital systems. Eight macrocells can hold multiple product-term equations, while the 16V8 organization supports up to 16 inputs and 8 I/O outputs. Electrically erasable Flash technology permits firmware-like logic updates during equipment maintenance, reducing board respin risk. For dependable implementation, validate address overlap, propagate uncertain states through invalid-command outputs, and preserve required setup and hold margins around clocked outputs under the worst-case 25 ns timing scenario.
Được đề xuất
Test Equipment Control Logic
The ATF16V8BQL-25PC can consolidate small control functions in legacy test and measurement equipment, such as relay-sequence enable logic, status-latch decoding, or front-panel command gating. The 25 ns propagation delay supports moderate digital control paths, and eight configurable I/O outputs allow the same device to participate in both input decoding and output generation. The through-hole 20-PDIP package also simplifies repair and prototyping. Before integrating it into a measuring chain, keep it out of precision analog paths, provide clean 5 V power, and account for unused-pin and reset-state behavior in the system verification plan.
Được đề xuất
Low-Power Embedded Glue Logic
The ATF16V8BQL-25PC fits embedded systems that require a small amount of configurable logic beside a primary controller but value low standby consumption. Input Transition Detection automatically moves the PLD toward its low-power state when inputs are idle, and the manufacturer lists a typical standby current of 5 mA. The electrically erasable architecture allows logic updates without a new package, while the 25 ns speed grade addresses routine handshake and control functions. Designers should confirm whether 5 mA meets the product's sleep-current target and should include programming, configuration-security, and in-field update procedures in the production plan.
Được đề xuất
Telecom and Communications Interface
The ATF16V8BQL-25PC can implement auxiliary line-state decoding, enable generation, or alarm masking in legacy telecommunications equipment. The 20-pin PAL-compatible architecture is useful when updating established control boards without changing their through-hole footprint, and the 8-macrocell capacity handles compact multi-signal equations. The 25 ns propagation delay is suitable for many supervisory paths rather than high-speed serial datapaths. Layout should keep the PLD away from switching power stages, use a decoupled 5 V rail, and treat all control outputs as potentially asynchronous until the system specifies safe states for power-up and reset conditions.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATF16V8BQL-25PC — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATF16V8B-25PC |
|---|---|---|
| Package | 20-PDIP | 20-PDIP - same |
| Brand | Microchip Technology | Microchip Technology |
| Product Type | Low-power electrically erasable PLD | Standard-power electrically erasable PLD |
| Macrocells | 8 | 8 |
| Maximum Inputs | 16 inputs | 16 inputs |
| I/O Outputs | 8 I/O | 8 I/O |
| Supply Voltage | 5 V | 5 V |
| Propagation Delay | 25 ns | 25 ns |
| Power-Down Feature | Automatic low-power mode through Input Transition Detection | No ATF16V8BQL Input Transition Detection feature |
Bảo phân biệt quan trọng
- Lower-power operating variant (vsATF16V8B-25PC)
- Direct package and timing alignment (vsATF16V8B-25PC)
- Nonvolatile reprogrammable configuration (vsATF16V8B-25PC)
Ghi chú thiết kế
Use a regulated 5 V rail and place the manufacturer-recommended bypass capacitor immediately between the VCC and GND pins. Keep the supply and return paths short because the 20-PDIP footprint can support long PCB traces if routing is not constrained. In battery-powered equipment, include the 5 mA typical standby current and operating current in the active and idle power budgets before confirming that the low-power variant provides a worthwhile system-level saving.
Do not treat the ATF16V8B and ATF16V8BQL as identical merely because they share the 16V8 architecture and 20-PDIP package. The ATF16V8BQL includes Input Transition Detection and quarter-power characteristics, while the ATF16V8B is the standard-power member. Before substitution, compare the programmed equations, clock behavior, output-enable polarity, unused-pin treatment, AC timing, and power requirements against the manufacturer datasheet.
Reserve the package pin assignments shown in the manufacturer pin-description table and mark all unused inputs so their electrical state is controlled during programming, reset, and power-up. Route the clock with short geometry and maintain separation from switching-regulator and relay-control traces. Although the propagation-delay grade is 25 ns, edge-rate and crosstalk margin cannot be inferred from that figure alone, so validate the completed board with realistic loading and worst-case supply conditions.
The ATF16V8B architecture emulates a 20-pin PAL arrangement, but a generic PAL pinout is not a substitute for the manufacturer package drawing. Verify whether a design requires registered, complex combinatorial, or simple combinatorial behavior because the operating mode is selected automatically by the programming software. Recheck feedback-product-term allocation and clocked-output constraints during compilation rather than relying on a manual equation conversion.
Thông tin tuân thủ
The ATF16V8B family datasheet includes green-package ordering information, but the manufacturer datasheet excerpt does not establish a specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status for this exact legacy MPN.