ATXMEGA128B1-AU 32MHz 128KB Flash MCU | Microchip
MPN: ATXMEGA128B1-AU ✓ 啟用中ATXMEGA128B1-AU 概覽
An 8/16-bit microcontroller is a programmable semiconductor that executes embedded control instructions using an internal CPU, nonvolatile memory, and peripheral interfaces. The AVR XMEGA family combines a Harvard-style memory architecture, high-speed execution, and event-oriented peripherals in a single device. Within the embedded hierarchy, it sits above simple 8-bit controllers because its 16-bit-oriented AVR architecture supports up to 32 MIPS while retaining byte-oriented programming compatibility.
The ATXMEGA128B1-AU includes a two-channel DMA controller, a four-channel event system, and a USB Full-Speed device controller. Its memory organization includes 128 KB Flash, 8 KB SRAM, and 2 KB EEPROM, while the LCD interface supports up to 4 x 40 segments. These resources allow firmware movement between memory regions and coordinated handling of events without excessive processor intervention.
Up to 53 I/O pins provide access to communication, timer, analog, and general-purpose digital functions. The 100-TQFP arrangement makes the device suitable for compact embedded boards that require extensive peripheral connectivity without using a very large fine-pitch package. Operating voltage options shown for this device include 1.8 V, 2.5 V, and 3.3 V, supporting integration with low-voltage sensors, communications transceivers, and USB interface circuitry.
Typical uses include USB-connected data acquisition, industrial control modules, human-machine interfaces, low-power embedded instruments, and segmented LCD equipment. The DMA controller and event system are especially useful when data acquisition, display updates, and communication must coexist with deterministic control-loop execution. The 32 MHz maximum clock rate provides additional timing margin for protocol handling and signal processing.
PCB design should preserve short return paths around decoupling capacitors and provide clean routing for USB and clock signals. Firmware development should account for the dedicated boot-code section, interrupt-driven event handling, and peripheral contention between DMA, USB, timers, and the LCD controller. Confirm the exact pin multiplexing, clock configuration, and peripheral availability against the manufacturer datasheet before finalizing a board.
This page combines the manufacturer product overview with practical memory, peripheral, package, and sourcing guidance. It also identifies verified same-package alternatives and explains where firmware, timing, or temperature-grade differences must be reviewed before making a replacement decision.
直接替換替代品,適用於 ATXMEGA128B1-AU — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ATXMEGA128B1-AU (相同外形與佔位) — 差異在於 DMA Channels, Event System Channels, General-Purpose I/O Pins, Package, RoHS Status.
ATXMEGA128B1-AN
✅ 直接替換📋 參考替代品(不在目錄中)
ATXMEGA128D3-AU
✅ 直接替換📋 參考替代品(不在目錄中)
ATXMEGA128A1-AU
✅ 直接替換聯絡詢價
查看資料表 →ATXMEGA128B1-AU 最大額定值與電氣特性
| Product Type | 8/16-bit AVR XMEGA B1 microcontroller |
| 最大時脈頻率 | 32 MHz |
| Maximum CPU Throughput | Up to 32 MIPS |
| Program Memory | 128 KB Flash |
| Boot Code Section | 8 KB |
| SRAM | 8 KB |
| EEPROM | 2 KB |
| General-Purpose I/O Pins | 53 pins |
| DMA Channels | 2 channels |
| Event System Channels | 4 channels |
| USB Interface | USB Full-Speed device |
| LCD Controller | Up to 4 x 40 segments |
| Operating Voltage Options | 1.8 V, 2.5 V, and 3.3 V |
| 封裝 | 100-pin TQFP, 14 x 14 mm |
| 安裝類型 | Surface mount |
| Packaging | Tray |
| Architecture | AVR XMEGA 8/16-bit |
| Program Memory Type | In-system self-programmable Flash |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
ATXMEGA128B1-AU 100-pin tqfp, 14 x 14 mm 腳位配置指南
ATXMEGA128B1-AU(100-pin tqfp, 14 x 14 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: ATXMEGA128B1-AU.
請參閱 資料表 以查看完整腳位配置。
典型應用
ATXMEGA128B1-AU 適用於 6 應用s: USB Data Acquisition, Industrial Control Module, Segmented LCD Human-Machine Interface, Low-Power Sensor Node, USB Communication Adapter, Embedded Test and Measurement Instrument.
USB Data Acquisition
The ATXMEGA128B1-AU fits USB-connected measurement systems because it combines a USB Full-Speed device controller with a 32 MHz AVR processor and 128 KB of self-programmable Flash. Its two-channel DMA controller can move sampled data between memory regions with limited CPU involvement, while the four-channel event system can coordinate triggers and timing events. This architecture is useful for portable instruments that transfer sensor data to a host computer without requiring a separate USB interface controller. The implementation should use short USB traces, solid ground-plane continuity, and correctly selected USB-series impedance routing. Firmware must also coordinate USB interrupts with DMA access to avoid corrupting transfers while data is being processed.
推薦
Industrial Control Module
The ATXMEGA128B1-AU supports compact industrial control modules that need substantial I/O, local event handling, and flexible communication. Its 53 general-purpose I/O pins can connect digital inputs, outputs, status indicators, and external interface circuits, while the 128 KB Flash provides room for protocol stacks and application logic. The two DMA channels are useful when sensor or actuator traffic must continue during display servicing or host communication. Operating-voltage options of 1.8 V, 2.5 V, and 3.3 V allow the controller to share power domains with appropriate transceivers. Designers should confirm temperature requirements, isolation strategy, grounding, and transient protection before using the device in industrial environments.
推薦
Segmented LCD Human-Machine Interface
The ATXMEGA128B1-AU is well suited to human-machine interfaces based on segmented LCDs because it includes a controller capable of driving up to 4 x 40 segments. At the same time, the device retains 53 I/O pins for buttons, indicators, communication ports, and configuration inputs. Its 32 MHz execution rate allows the firmware to update the display while responding to events and maintaining a USB or serial control link. The integrated event system can help synchronize display updates with user activity or sampled process data. Designers should follow the manufacturer LCD timing and bias requirements, allow adequate settling time for the glass, and separate display drive currents from sensitive analog circuitry where practical.
推薦
Low-Power Sensor Node
The ATXMEGA128B1-AU can serve as the central controller in a low-power sensor node that gathers digital measurements and communicates through USB or another peripheral interface. Its selectable 1.8 V, 2.5 V, and 3.3 V operating options support low-voltage sensor ecosystems, and the event system can coordinate periodic sampling with communication activity. The two DMA channels reduce processor involvement during transfers, helping preserve responsiveness when the node also manages local controls. Firmware should use the device’s low-power modes during idle intervals, disable unused peripherals, and maintain stable regulator sequencing. PCB layout should place decoupling capacitors close to supply pins and provide a quiet return path for analog sensor connections.
推薦
USB Communication Adapter
The ATXMEGA128B1-AU is appropriate for compact protocol adapters that translate between a host USB connection and embedded serial, control, or data-acquisition circuitry. The USB Full-Speed device controller removes the need for a separate USB transceiver or host controller, while 8 KB of SRAM supports buffering and the 128 KB Flash accommodates protocol and configuration logic. DMA can accelerate transfers between peripheral peripherals and memory, reducing the processing burden during continuous data movement. A robust adapter also needs ESD protection, controlled cable or connector design, firmware enumeration support, and verification of the USB operating-current budget. The exact 100-pin land pattern must be used during PCB layout.
推薦
Embedded Test and Measurement Instrument
The ATXMEGA128B1-AU fits embedded test and measurement instruments that combine local control, event-driven acquisition, and USB reporting. Its 32 MHz throughput provides useful margin for timing routines, communication protocols, and data processing, while the event system can coordinate triggers across timers and external events. The two-channel DMA controller is valuable when acquisition must continue while results are transmitted or displayed. The broad I/O count allows connection to sensors, relay drivers, status LEDs, and front-panel controls without requiring a separate programmable logic device. For accurate analog measurements, keep the MCU power and clock references separated from sensitive front ends, and follow the manufacturer’s recommended grounding and decoupling layout.
推薦
推薦產品摘要
工程參考資料,適用於 ATXMEGA128B1-AU — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ATXMEGA128B1-AN | ATXMEGA128D3-AU | ATXMEGA128A1-AU |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-TQFP (14x14) | 100-TQFP (14x14) - same | 100-TQFP (14x14) - same | 100-TQFP (14x14) - same |
| Product Family | AVR XMEGA B1 | AVR XMEGA B1 | AVR XMEGA D3 | AVR XMEGA A1 |
| Program Memory | 128 KB Flash | 128 KB Flash | 128 KB Flash | 128 KB Flash |
主要差異化特點
- Closest same-package temperature-grade alternative (對比ATXMEGA128B1-AN)
- Substantial integrated peripheral set (對比ATXMEGA128A1-AU)
- 32 MHz processing rate with 128 KB Flash (對比ATXMEGA128D3-AU)
設計說明
Place the required input and output decoupling capacitors directly beside their corresponding supply and ground pins, following the manufacturer layout and component-selection guidance. Keep the USB data-pair routing short, continuous, and over a continuous ground plane. The 100-pin TQFP lead pitch also requires careful footprint verification: confirm pin-1 orientation, exposed-pad requirements if applicable, solder-mask clearance, and paste volume before releasing the PCB artwork.
The device supports 1.8 V, 2.5 V, and 3.3 V operation, but the selected supply must satisfy the voltage, clock, and USB requirements for the complete design. Sequence rails consistently with the USB interface circuitry and avoid operating peripherals outside their permitted voltage ranges. If the board also includes sensors or transceivers, budget their current together with the MCU rather than sizing the regulator from the MCU name alone.
Use the event system and DMA channels to separate timed sampling from buffer movement, but ensure each peripheral’s event routing and channel assignment is checked against the device documentation. Review interrupt priority, DMA arbitration, and memory contention in firmware. For designs involving external precision references or analog front ends, maintain quiet return paths and avoid routing clock or high-current switching nodes beneath sensitive analog sections.
合規資訊
Compliance status has not been established for the exact ordering code. Confirm current environmental, automotive, and material declarations with Microchip Technology before production release.