BCM5482A2KFBG - Dual-Port Gigabit Ethernet PHY | Broadcom
MPN: BCM5482A2KFBG ✓ 啟用中BCM5482A2KFBG 概覽
An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data into signals suitable for copper-cable transmission while managing line signaling, link negotiation, and recovery. Within the network-interface hierarchy, the BCM5482A2KFBG sits below the Ethernet MAC and above the transformer and magnetics. Integrating two PHY channels into one package reduces board area in designs that need two copper-network connections.
The principal benefits of this device are its dual-port architecture, support for three Ethernet speed classes, and 121-BGA package. Each port can operate at 10 Mb/s, 100 Mb/s, or 1 Gb/s, allowing a single board design to support legacy and gigabit links. The full-duplex capability is suited to simultaneous bidirectional traffic, while half-duplex support provides compatibility with legacy network equipment.
Technically, the BCM5482A2KFBG is a CMOS Ethernet transceiver rather than a general-purpose processor. Its two PHY channels provide the physical-layer interface between a digital network controller and external magnetic interface circuitry. Exact pin assignments, clock requirements, register definitions, power rails, media-unit interfaces, and electrical characteristics should be taken from the Broadcom manufacturer datasheet for the assembled board.
Typical uses include dual-port routers, network switches, industrial Ethernet gateways, set-top equipment, embedded Linux systems, and network-interface cards. In each application, the PHY can support two copper links independently, reducing the number of separate Ethernet transceiver packages required on the PCB.
The principal design consideration is PCB implementation. A 121-BGA device requires fine-pitch routing, controlled escape geometry, and careful power and ground distribution. Follow the manufacturer layout, decoupling, thermal, and magnetics guidance rather than inferring high-speed routing requirements from generic BGA rules.
This page consolidates the verified product identity, package information, speed-class coverage, sourcing data, replacement considerations, and engineering guidance into one design reference. It also distinguishes true footprint-compatible Broadcom alternatives from functional Ethernet PHY options that require different packages, interfaces, or board layouts.
直接替換替代品,適用於 BCM5482A2KFBG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: BCM5482A2KFBG (相同外形與佔位) — 差異在於 Package, Product Type.
BCM5482HA2KFBG
✅ 直接替換📋 參考替代品(不在目錄中)
BCM5482SEA2KFBG
✅ 直接替換📋 參考替代品(不在目錄中)
BCM5482SHEA2IFBG
✅ 直接替換📋 參考替代品(不在目錄中)
BCM54220SB0IFBG
✅ 直接替換📋 參考替代品(不在目錄中)
BCM54640B0IFBG
✅ 直接替換📋 參考替代品(不在目錄中)
BCM5482A2KFBG 最大額定值與電氣特性
| Product Type | Dual-port Ethernet transceiver |
| Supported Ethernet Speeds | 10 Mb/s, 100 Mb/s, 1 Gb/s |
| Port Count | 2 ports |
| Duplex Operation | Full duplex and half duplex |
| Physical Layer Standard | 10/100/1000BASE-T |
| Process Technology | CMOS |
| 封裝 | 121-BGA |
| 腳位數 | 121 balls |
| 安裝類型 | Surface mount |
| Interface Category | Ethernet PHY |
| Maximum Data Rate | 1 Gb/s per port |
| Minimum Data Rate | 10 Mb/s per port |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
BCM5482A2KFBG 121-bga 腳位配置指南
BCM5482A2KFBG(121-bga 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: BCM5482A2KFBG.
請參閱 資料表 以查看完整腳位配置。
典型應用
BCM5482A2KFBG 適用於 6 應用s: Dual-Port Network Router, Industrial Ethernet Gateway, Network Switch Line Card, Set-Top Box and Media Gateway, Embedded Linux Network Interface, Network Interface Card.
Dual-Port Network Router
The BCM5482A2KFBG fits routers requiring two copper Ethernet connections in one device. Each PHY channel supports 10 Mb/s, 100 Mb/s, and 1 Gb/s, allowing the same hardware to address legacy 10/100BASE-T equipment as well as Gigabit Ethernet clients. Placing two PHYs under one network controller can reduce PCB area and simplify power sequencing. The implementation should provide independent magnetics, isolation, and controlled-impedance routing for both ports, while confirming that all required management, clock, and status signals are available on the chosen Broadcom variant.
推薦
Industrial Ethernet Gateway
The BCM5482A2KFBG is suitable for gateways that must bridge local copper networks to an embedded controller or upstream processor. Its two ports support 10BASE-T, 100BASE-T, and 1000BASE-T, making it useful where field equipment may connect through older or newer Ethernet infrastructure. A dual-channel implementation avoids two separate PHY packages, but the board must provide appropriate surge protection, isolation, grounding, and magnetics. Confirm the device temperature grade and electrical limits against the gateway’s environmental requirements before production release.
推薦
Network Switch Line Card
The BCM5482A2KFBG can supply two 10/100/1000BASE-T physical-layer channels for a switch line card or compact access switch. Supporting all three Ethernet speed classes on each port helps the card interoperate with mixed legacy and Gigabit deployments. Its 121-BGA package supports dense integration but requires careful escape routing between fine-pitch balls and the magnetics or RJ45 area. Validate fanout, layer transitions, return paths, and impedance control using the manufacturer land pattern and high-speed layout guidance.
推薦
Set-Top Box and Media Gateway
The BCM5482A2KFBG fits media systems that need one or more Ethernet links alongside video, storage, or control functions. The device’s dual-port capability can support connectivity to a home network and local service equipment without requiring separate PHY packages. Because link speeds can be negotiated across 10 Mb/s, 100 Mb/s, and 1 Gb/s, the implementation can support legacy switches and high-speed transfers. Keep the PHY, magnetics, and connector return paths physically separated from noisy switching regulators and high-current digital circuitry.
推薦
Embedded Linux Network Interface
The BCM5482A2KFBG can provide hardware network connectivity for an embedded Linux system through an external MAC or a companion network controller. Supporting three speed classes broadens compatibility with development networks, peripherals, and service equipment. Two PHY channels can separate management traffic from application traffic or provide a fallback path for link diagnostics. Firmware must support the PHY interface and status behavior of the exact BCM5482 variant, while the PCB must preserve clean media-unit signaling and isolated network-domain boundaries.
推薦
Network Interface Card
The BCM5482A2KFBG is applicable to dual-port network interface cards intended to add copper Ethernet connectivity to a computer or embedded chassis. Each channel can operate from 10BASE-T through 1000BASE-T, supporting legacy infrastructure while retaining gigabit throughput. Two integrated PHY channels can simplify connector and magnetics placement relative to two discrete transceiver packages. A production design should verify host-interface requirements, reference clocks, MDIO management paths, LED behavior, and the exact Broadcom ordering code before finalizing the schematic.
推薦
推薦產品摘要
工程參考資料,適用於 BCM5482A2KFBG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | BCM5482HA2KFBG | BCM5482SEA2KFBG | BCM5482SHEA2IFBG | BCM54220SB0IFBG | BCM54640B0IFBG |
|---|---|---|---|---|---|---|
| Package | 121-BGA | 121-BGA | 121-BGA | 121-BGA | 121-BGA | 121-BGA |
| Brand | Broadcom | Broadcom | Broadcom | Broadcom | Broadcom | Broadcom |
| Product Type | Dual-port Ethernet transceiver | Dual-port Ethernet transceiver | Ethernet transceiver | Ethernet PHY | Ethernet transceiver | Ethernet transceiver |
| Supported Data Rates | 10 Mb/s, 100 Mb/s, 1 Gb/s | 10 Mb/s, 100 Mb/s, 1 Gb/s | 10 Mb/s, 100 Mb/s, 1 Gb/s | 10 Mb/s, 100 Mb/s, 1 Gb/s | 10 Mb/s, 100 Mb/s, 1 Gb/s | 10 Mb/s, 100 Mb/s, 1 Gb/s |
| Maximum Data Rate | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port | 1 Gb/s per port |
主要差異化特點
- Two independently addressed Gigabit Ethernet PHY channels (對比BCM5482HA2KFBG)
- Broad support for mixed-speed copper Ethernet (對比BCM54640B0IFBG)
- Single-package integration for two copper network links (對比TLK105L)
- Full-duplex and half-duplex operation (對比KSZ9031)
設計說明
Treat the 121-BGA escape routing as the dominant layout constraint. Follow the Broadcom land pattern for ball locations, solder-mask design, and pad geometry, and preserve the recommended ball-to-ball and ball-to-component clearances. Fan out each media-unit, management, clock, power, and ground connection according to the manufacturer stack-up guidance before placing the connector or magnetics. Do not derive a footprint from generic BGA rules.
Separate each Ethernet channel’s signal path from the other channel and from high-current switching circuitry. Maintain continuous return paths beneath high-speed traces, use the manufacturer’s recommended reference-plane transitions, and control impedance on the media interface. Keep the PHY-to-magnetics and magnetics-to-connector sections short where the application circuit specifies it, while accounting for component and connector placement tolerance rather than relying only on nominal trace length.
Use the manufacturer’s recommended power rails, decoupling network, and startup sequencing without substituting equivalent-looking capacitors. Place required input and output capacitors adjacent to their associated balls with short ground vias, and verify that the power-supply network does not disturb link training or media-unit operation. Decoupling capacitance, voltage tolerance, ESR, and placement requirements should be selected from the Broadcom manufacturer datasheet rather than assumed from general practice.
A matching Ethernet speed rating does not prove that an alternative ordering code is interchangeable. Before substituting any BCM5482-family candidate, compare every BGA ball, power domain, reference-clock requirement, reset behavior, management address, register default, strap configuration, and media-unit connection. Also confirm the exact Broadcom ordering code and qualification status; otherwise, treat the candidate as a redesign rather than a drop-in replacement.
合規資訊
RoHS and REACH status require confirmation for the exact Broadcom ordering code. The BCM5482A2KFBG is an Ethernet interface IC rather than an automotive-qualified device, so AEC-Q100 status is not applicable.