Broadcom

BCM5482A2KFBG - Dual-Port Gigabit Ethernet PHY | Broadcom

부품 번호: BCM5482A2KFBG ✓ 활성
121-BGA Package 10 Mb/s, 100 Mb/s, 1 Gb/s Speed
MOQ: 1 |

BCM5482A2KFBG 개요

The Broadcom BCM5482A2KFBG is a dual-port 10/100/1000BASE-T Ethernet transceiver IC packaged in a 121-ball BGA. It combines two Gigabit Ethernet physical-layer channels with full-duplex and half-duplex operation for network-interface, router, switch, and embedded communications equipment. The device uses CMOS technology and supports link rates of 10 Mb/s, 100 Mb/s, and 1 Gb/s on each port.

An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data into signals suitable for copper-cable transmission while managing line signaling, link negotiation, and recovery. Within the network-interface hierarchy, the BCM5482A2KFBG sits below the Ethernet MAC and above the transformer and magnetics. Integrating two PHY channels into one package reduces board area in designs that need two copper-network connections.

The principal benefits of this device are its dual-port architecture, support for three Ethernet speed classes, and 121-BGA package. Each port can operate at 10 Mb/s, 100 Mb/s, or 1 Gb/s, allowing a single board design to support legacy and gigabit links. The full-duplex capability is suited to simultaneous bidirectional traffic, while half-duplex support provides compatibility with legacy network equipment.

Technically, the BCM5482A2KFBG is a CMOS Ethernet transceiver rather than a general-purpose processor. Its two PHY channels provide the physical-layer interface between a digital network controller and external magnetic interface circuitry. Exact pin assignments, clock requirements, register definitions, power rails, media-unit interfaces, and electrical characteristics should be taken from the Broadcom manufacturer datasheet for the assembled board.

Typical uses include dual-port routers, network switches, industrial Ethernet gateways, set-top equipment, embedded Linux systems, and network-interface cards. In each application, the PHY can support two copper links independently, reducing the number of separate Ethernet transceiver packages required on the PCB.

The principal design consideration is PCB implementation. A 121-BGA device requires fine-pitch routing, controlled escape geometry, and careful power and ground distribution. Follow the manufacturer layout, decoupling, thermal, and magnetics guidance rather than inferring high-speed routing requirements from generic BGA rules.

This page consolidates the verified product identity, package information, speed-class coverage, sourcing data, replacement considerations, and engineering guidance into one design reference. It also distinguishes true footprint-compatible Broadcom alternatives from functional Ethernet PHY options that require different packages, interfaces, or board layouts.

드롭인 대체품: BCM5482A2KFBG — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: BCM5482A2KFBG (동일 폼 팩터 및 풋프린트) — 차이점: Package, Product Type.

Broadcom
Package: 121-pin BGA
Product Type: Dual-port Ethernet physical-layer transceiver
비교 대상: BCM5482A2KFBG →

BCM5482HA2KFBG

✅ 드롭인
📦 121-BGA
Data-rate coverage is identical at 10/100/1000 Mb/s, while family-specific feature and ordering-code differences are 10%

📋 참조 대체품 (카탈로그에 없음)

BCM5482SEA2KFBG

✅ 드롭인
📦 121-BGA
Supported data rates are identical at 10/100/1000 Mb/s; ordering-code and qualification differences are 10%

📋 참조 대체품 (카탈로그에 없음)

BCM5482SHEA2IFBG

✅ 드롭인
📦 121-BGA
Ethernet speed classes match exactly at 10/100/1000 Mb/s; feature, qualification, and ordering differences are 20%

📋 참조 대체품 (카탈로그에 없음)

BCM54220SB0IFBG

✅ 드롭인
📦 121-BGA
Supported rates match exactly at 10/100/1000 Mb/s; interface and family-specific feature differences are 20%

📋 참조 대체품 (카탈로그에 없음)

BCM54640B0IFBG

✅ 드롭인
📦 121-BGA
Supported rates match exactly at 10/100/1000 Mb/s; port, interface, and family-specific differences are 30%

📋 참조 대체품 (카탈로그에 없음)

BCM5482A2KFBG 최대 정격 & 전기적 특성

Product Type Dual-port Ethernet transceiver
Supported Ethernet Speeds 10 Mb/s, 100 Mb/s, 1 Gb/s
Port Count 2 ports
Duplex Operation Full duplex and half duplex
Physical Layer Standard 10/100/1000BASE-T
Process Technology CMOS
패키지 121-BGA
핀 수 121 balls
실장 유형 Surface mount
Interface Category Ethernet PHY
Maximum Data Rate 1 Gb/s per port
Minimum Data Rate 10 Mb/s per port
RoHS 상태 unknown
REACH Status unknown

BCM5482A2KFBG 121-bga 핀 구성 가이드

BCM5482A2KFBG(121-bga 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.

BCM5482A2KFBG의 121-bga 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: BCM5482A2KFBG.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

BCM5482A2KFBG 적합 용도: 6 애플리케이션s: Dual-Port Network Router, Industrial Ethernet Gateway, Network Switch Line Card, Set-Top Box and Media Gateway, Embedded Linux Network Interface, Network Interface Card.

🌐

Dual-Port Network Router

The BCM5482A2KFBG fits routers requiring two copper Ethernet connections in one device. Each PHY channel supports 10 Mb/s, 100 Mb/s, and 1 Gb/s, allowing the same hardware to address legacy 10/100BASE-T equipment as well as Gigabit Ethernet clients. Placing two PHYs under one network controller can reduce PCB area and simplify power sequencing. The implementation should provide independent magnetics, isolation, and controlled-impedance routing for both ports, while confirming that all required management, clock, and status signals are available on the chosen Broadcom variant.

🏭

Industrial Ethernet Gateway

The BCM5482A2KFBG is suitable for gateways that must bridge local copper networks to an embedded controller or upstream processor. Its two ports support 10BASE-T, 100BASE-T, and 1000BASE-T, making it useful where field equipment may connect through older or newer Ethernet infrastructure. A dual-channel implementation avoids two separate PHY packages, but the board must provide appropriate surge protection, isolation, grounding, and magnetics. Confirm the device temperature grade and electrical limits against the gateway’s environmental requirements before production release.

🖥️

Network Switch Line Card

The BCM5482A2KFBG can supply two 10/100/1000BASE-T physical-layer channels for a switch line card or compact access switch. Supporting all three Ethernet speed classes on each port helps the card interoperate with mixed legacy and Gigabit deployments. Its 121-BGA package supports dense integration but requires careful escape routing between fine-pitch balls and the magnetics or RJ45 area. Validate fanout, layer transitions, return paths, and impedance control using the manufacturer land pattern and high-speed layout guidance.

📺

Set-Top Box and Media Gateway

The BCM5482A2KFBG fits media systems that need one or more Ethernet links alongside video, storage, or control functions. The device’s dual-port capability can support connectivity to a home network and local service equipment without requiring separate PHY packages. Because link speeds can be negotiated across 10 Mb/s, 100 Mb/s, and 1 Gb/s, the implementation can support legacy switches and high-speed transfers. Keep the PHY, magnetics, and connector return paths physically separated from noisy switching regulators and high-current digital circuitry.

🧩

Embedded Linux Network Interface

The BCM5482A2KFBG can provide hardware network connectivity for an embedded Linux system through an external MAC or a companion network controller. Supporting three speed classes broadens compatibility with development networks, peripherals, and service equipment. Two PHY channels can separate management traffic from application traffic or provide a fallback path for link diagnostics. Firmware must support the PHY interface and status behavior of the exact BCM5482 variant, while the PCB must preserve clean media-unit signaling and isolated network-domain boundaries.

💻

Network Interface Card

The BCM5482A2KFBG is applicable to dual-port network interface cards intended to add copper Ethernet connectivity to a computer or embedded chassis. Each channel can operate from 10BASE-T through 1000BASE-T, supporting legacy infrastructure while retaining gigabit throughput. Two integrated PHY channels can simplify connector and magnetics placement relative to two discrete transceiver packages. A production design should verify host-interface requirements, reference clocks, MDIO management paths, LED behavior, and the exact Broadcom ordering code before finalizing the schematic.

What is the Broadcom BCM5482A2KFBG?
The Broadcom BCM5482A2KFBG is a dual-port CMOS Ethernet transceiver that supports 10BASE-T, 100BASE-T, and 1000BASE-T links. It provides two physical-layer channels at rates up to 1 Gb/s per port in a 121-BGA package. According to the Broadcom manufacturer datasheet, the device is intended for copper Ethernet network-interface equipment operating in full-duplex or half-duplex mode.
What Ethernet speeds does BCM5482A2KFBG support?
The BCM5482A2KFBG supports 10 Mb/s, 100 Mb/s, and 1 Gb/s operation on each of its two Ethernet ports. This allows one physical-layer design to cover 10BASE-T, 100BASE-T, and 1000BASE-T networks. The Broadcom manufacturer datasheet identifies the device as a dual-port 10/100/1000BASE-T Gigabit Ethernet transceiver.
Where can I download the BCM5482A2KFBG datasheet PDF?
The BCM5482A2KFBG datasheet PDF can be obtained from the Broadcom datasheet listing linked on this page or from the linked product documentation record. The manufacturer document describes the device as a dual-port 10/100/1000BASE-T Gigabit Ethernet transceiver. Use the Broadcom document for the authoritative pin assignments, electrical limits, register map, and application circuit.
Where can I find the BCM5482A2KFBG pinout?
The BCM5482A2KFBG pinout is defined in the Broadcom manufacturer datasheet and includes 121 BGA balls. The package information available for this exact ordering code identifies a 121-BGA device, but a ball-by-ball assignment is not reproduced on this page. Use the datasheet pin-description table and land-pattern guidance when assigning PCB tracks, power rails, grounds, and media-unit connections.
What are the key specifications of BCM5482A2KFBG that engineers should know?
The key BCM5482A2KFBG specifications are two Ethernet ports, support for 10 Mb/s, 100 Mb/s, and 1 Gb/s data rates, full-duplex and half-duplex operation, CMOS construction, and a 121-BGA package. According to the Broadcom manufacturer datasheet, the device is a copper-network physical-layer transceiver rather than a complete Ethernet controller.
What can replace the BCM5482A2KFBG?
A BCM5482A2KFBG replacement must first match its 121-BGA footprint, two-channel architecture, and 10/100/1000 Mb/s PHY function. BCM5482HA2KFBG, BCM5482SEA2KFBG, and BCM5482SHEA2IFBG are the closest Broadcom family candidates identified for comparison. Final interchangeability requires checking every ball assignment, register behavior, power rail, and media-unit interface against the manufacturer datasheet.
Is BCM5482A2KFBG the same as BCM5482HA2KFBG?
BCM5482HA2KFBG is a closely related Broadcom BCM5482-family option, but it should not be treated as automatically identical without a complete pin and register review. Both are associated with the BCM5482 dual-port 10/100/1000BASE-T product family. The comparison record reports the same supported speed classes, while qualification, feature, and ordering differences require confirmation from the manufacturer documentation.
BCM5482A2KFBG vs BCM54220SB0IFBG: which is better for a dual-port router?
BCM54220SB0IFBG is the better candidate for an existing dual-port router only if its complete footprint, ball assignments, register map, electrical limits, and management features satisfy the design. The cross-reference record associates it with BCM5482A2KFBG, and both support 10 Mb/s, 100 Mb/s, and 1 Gb/s operation. Exact suitability cannot be established from the speed ratings alone.
When should I choose BCM5482A2KFBG over BCM54640B0IFBG?
Choose BCM5482A2KFBG when the design specifically targets the BCM5482 121-BGA implementation and its associated pin, register, and interface behavior. BCM54640B0IFBG is a separate Broadcom Ethernet product family that appears in replacement comparisons but is not automatically pin-to-pin compatible. Use it only after its datasheet confirms the required package, ports, speed modes, and management interface.
Is BCM5482A2KFBG suitable for industrial Ethernet equipment?
The BCM5482A2KFBG can be suitable for industrial Ethernet equipment when its electrical ratings, temperature grade, reliability requirements, and certification obligations are acceptable for the installation environment. The confirmed device description identifies a dual-port 10/100/1000BASE-T transceiver in a 121-BGA package. Confirm the operating-temperature range, isolation strategy, surge requirements, and industrial qualification before releasing the design.
What is the lead time for BCM5482A2KFBG?
The current lead time for BCM5482A2KFBG should be requested through the Request a Quote form on this page because stock and scheduling can change by order quantity and sourcing status. The part is identified as a Broadcom dual-port 10/100/1000BASE-T transceiver in a 121-BGA package. Include the target quantity, date code requirement, and shipping destination with the request.
Is BCM5482A2KFBG in stock?
Current BCM5482A2KFBG inventory should be checked through the Request a Quote form on this page rather than inferred from a catalog page. The device is a dual-port 10/100/1000BASE-T Ethernet transceiver in a 121-BGA package. A quotation response can confirm available inventory, scheduled lead time, package quantity, and any date-code constraints.
What is the price of BCM5482A2KFBG?
The current price of BCM5482A2KFBG depends on order quantity, date-code requirements, and sourcing conditions. Use the Request a Quote form on this page to request a current unit-price breakdown and availability confirmation. The component is the Broadcom BCM5482A2KFBG dual-port 10/100/1000BASE-T transceiver packaged in a 121-BGA.
Where can I buy BCM5482A2KFBG online?
BCM5482A2KFBG can be requested through the Request a Quote form on this page. Provide the required quantity, target delivery date, acceptable date code, and shipping destination. The component is a Broadcom dual-port 10/100/1000BASE-T Gigabit Ethernet transceiver supplied in a 121-BGA package.
What is the best cross-brand equivalent for BCM5482A2KFBG?
The best cross-brand equivalent for BCM5482A2KFBG cannot be selected from Ethernet functionality alone; a true drop-in candidate must also reproduce the 121-BGA footprint and pin behavior. TLK105L, KSZ9031, and 88E1510 are identified as functionally similar Gigabit Ethernet PHY products, but none is established here as footprint-compatible. Treat them as redesign candidates until their package and pin assignments are verified.

엔지니어링 참조 데이터: BCM5482A2KFBG — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose BCM5482A2KFBG when the board is designed around Broadcom’s dual-port 10/100/1000BASE-T architecture in a 121-BGA package and the design needs both full-duplex and half-duplex operation. BCM5482HA2KFBG is the closest same-family candidate when its feature set, qualification, and ordering code satisfy the application. BCM5482SEA2KFBG and BCM5482SHEA2IFBG are appropriate only after a complete ball, register, clock, and electrical review. Use BCM54220SB0IFBG or BCM54640B0IFBG only when their interfaces are confirmed compatible with the existing PCB. TLK105L, KSZ9031, and 88E1510 provide related Gigabit Ethernet PHY functions but are not established as footprint-compatible alternatives; treat them as redesign candidates requiring a new schematic, layout, and verification effort.

대체품과의 비교

파라미터 이 제품 BCM5482HA2KFBG BCM5482SEA2KFBG BCM5482SHEA2IFBG BCM54220SB0IFBG BCM54640B0IFBG
Package 121-BGA 121-BGA 121-BGA 121-BGA 121-BGA 121-BGA
Brand Broadcom Broadcom Broadcom Broadcom Broadcom Broadcom
Product Type Dual-port Ethernet transceiver Dual-port Ethernet transceiver Ethernet transceiver Ethernet PHY Ethernet transceiver Ethernet transceiver
Supported Data Rates 10 Mb/s, 100 Mb/s, 1 Gb/s 10 Mb/s, 100 Mb/s, 1 Gb/s 10 Mb/s, 100 Mb/s, 1 Gb/s 10 Mb/s, 100 Mb/s, 1 Gb/s 10 Mb/s, 100 Mb/s, 1 Gb/s 10 Mb/s, 100 Mb/s, 1 Gb/s
Maximum Data Rate 1 Gb/s per port 1 Gb/s per port 1 Gb/s per port 1 Gb/s per port 1 Gb/s per port 1 Gb/s per port

주요 차별점

  • Two independently addressed Gigabit Ethernet PHY channels (vs BCM5482HA2KFBG)
  • Broad support for mixed-speed copper Ethernet (vs BCM54640B0IFBG)
  • Single-package integration for two copper network links (vs TLK105L)
  • Full-duplex and half-duplex operation (vs KSZ9031)

설계 노트

Treat the 121-BGA escape routing as the dominant layout constraint. Follow the Broadcom land pattern for ball locations, solder-mask design, and pad geometry, and preserve the recommended ball-to-ball and ball-to-component clearances. Fan out each media-unit, management, clock, power, and ground connection according to the manufacturer stack-up guidance before placing the connector or magnetics. Do not derive a footprint from generic BGA rules.

Separate each Ethernet channel’s signal path from the other channel and from high-current switching circuitry. Maintain continuous return paths beneath high-speed traces, use the manufacturer’s recommended reference-plane transitions, and control impedance on the media interface. Keep the PHY-to-magnetics and magnetics-to-connector sections short where the application circuit specifies it, while accounting for component and connector placement tolerance rather than relying only on nominal trace length.

Use the manufacturer’s recommended power rails, decoupling network, and startup sequencing without substituting equivalent-looking capacitors. Place required input and output capacitors adjacent to their associated balls with short ground vias, and verify that the power-supply network does not disturb link training or media-unit operation. Decoupling capacitance, voltage tolerance, ESR, and placement requirements should be selected from the Broadcom manufacturer datasheet rather than assumed from general practice.

A matching Ethernet speed rating does not prove that an alternative ordering code is interchangeable. Before substituting any BCM5482-family candidate, compare every BGA ball, power domain, reference-clock requirement, reset behavior, management address, register default, strap configuration, and media-unit connection. Also confirm the exact Broadcom ordering code and qualification status; otherwise, treat the candidate as a redesign rather than a drop-in replacement.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

RoHS and REACH status require confirmation for the exact Broadcom ordering code. The BCM5482A2KFBG is an Ethernet interface IC rather than an automotive-qualified device, so AEC-Q100 status is not applicable.

데이터 검증일: 2026-11-15 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

BCM5482A2KFBG datasheet BCM5482A2KFBG pinout BCM5482A2KFBG datasheet pdf BCM5482A2KFBG equivalent BCM5482A2KFBG replacement BCM5482A2KFBG cross reference BCM5482A2KFBG 121-BGA BCM5482A2KFBG dual port PHY Broadcom BCM5482A2KFBG BCM5482A2KFBG price BCM5482A2KFBG stock BCM5482A2KFBG vs BCM5482HA2KFBG BCM5482A2KFBG network router BCM5482A2KFBG 10/100/1000BASE-T BCM5482A2KFBG PCB layout

관련 부품 & 용어

Broadcom BCM5482A2KFBG BCM5482HA2KFBG BCM5482SEA2KFBG BCM5482SHEA2IFBG BCM54220SB0IFBG BCM54640B0IFBG TLK105L KSZ9031 88E1510 Ethernet transceiver Ethernet PHY physical-layer transceiver 10/100/1000BASE-T Gigabit Ethernet 10 Mb/s 100 Mb/s 1 Gb/s full duplex half duplex CMOS 121-BGA BGA package surface mount network interface Ethernet magnetics
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기