Harris Corporation

CD4018BF/3 - 10MHz CMOS Counter | Harris | Signal Processing

MPN: CD4018BF/3 ✗ 停產
5 V Vdss 20 V test condition Id 16-lead hermetic ceramic dual-in-line package Package 10 MHz typical at a 10 V supply Speed
MOQ: 1 |

CD4018BF/3 概覽

Harris Corporation CD4018BF/3 is a medium-speed CMOS presettable binary counter and divide-by-N circuit operating from a 5 V to 15 V supply in a 16-lead ceramic dual-in-line package. It provides a typical maximum operating frequency of 10 MHz at a 10 V supply, fully static operation, standardized symmetrical output characteristics, and 5 V, 10 V, and 15 V parametric ratings. The maximum input current is 1 µA at 18 V.

A CMOS presettable counter is a sequential logic circuit within the broader digital counter, divider, and counter/diverter categories. It advances its count when driven by a clock edge and can be loaded with an initial count through its parallel data inputs. The preset capability makes the device useful when a circuit must begin counting from a selected value, while the decode outputs provide access to selected counter states.

The CD4018BF/3 supports medium-speed operation and fully static operation, allowing the internal state to remain stable when no clock transition occurs. Standardized symmetrical output characteristics help simplify interfacing with other CMOS logic. Its parametric ratings at 5 V, 10 V, and 15 V permit design engineers to evaluate the same counter across several common supply levels rather than relying on one operating point.

The part uses positive-rail, single-supply CMOS technology, placing it in the CD4000 logic family. Its 16-lead hermetic ceramic dual-in-line package supports conventional through-hole assembly and provides a durable environmental enclosure for industrial, instrumentation, and legacy control applications. The suffix /3 identifies the particular Harris ordering variant, while the CD4018B designation identifies the counter family.

Typical uses include frequency division, event-counting, timing and delay generation, programmable sequence controllers, digital instrumentation, and industrial control logic. The divide-by-N capability is useful when a system needs a stable lower-frequency output derived from an external clock. Its preset inputs can also support modulo counting and repetitive timing sequences when the surrounding combinational logic defines the terminal count.

Designers should account for supply tolerances, propagation delay, clock pulse width, reset behavior, and the settling time of the preset inputs when establishing operating-frequency limits. Input levels must remain compatible with the selected CMOS supply range, and unused inputs should be tied to a defined logic level. The manufacturer datasheet should be used for the complete terminal description and timing characteristics before assigning nets in a new layout.

This product page combines the verified CD4018BF/3 identity, manufacturer-package information, operating-speed data, design guidance, and engineering-oriented comparison context. It also distinguishes the ceramic CDIP variant from lower-pin-count or surface-mount CD4018-family alternatives that cannot replace the target part without changing the printed-circuit-board footprint.

直接替換替代品,適用於 CD4018BF/3 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此產品無可直接替換的替代品。

申請替代品

CD4018BF/3 最大額定值與電氣特性

Product Type CMOS presettable binary counter and divide-by-N circuit
Technology CMOS
Maximum Operating Frequency 10 MHz typical at a 10 V supply
Fully Static Operation Yes
Quiescent Current Test Condition 20 V test condition
Maximum Input Current 1 µA at 18 V
Parametric Supply Rating 5 V
Parametric Supply Rating 10 V
Parametric Supply Rating 15 V
Output Characteristics Standardized and symmetrical
封裝 16-lead hermetic ceramic dual-in-line package
Number of Leads 16 leads
安裝類型 Through-hole
工作溫度範圍 -55 °C to +125 °C
Counter Resolution 5-bit

CD4018BF/3 16-lead hermetic ceramic dual-in-line package 腳位配置指南

CD4018BF/3(16-lead hermetic ceramic dual-in-line package 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。

CD4018BF/3 的 16-lead hermetic ceramic dual-in-line package 封裝腳位圖

無詳細腳位定義資料: CD4018BF/3.

請參閱 資料表 以查看完整腳位配置。

典型應用

CD4018BF/3 適用於 6 應用s: Frequency Division, Event and Pulse Counting, Programmable Timing Control, Digital Instrumentation, Industrial Sequence Control, Modulo Counter and Retriggerable Timer.

🔧

Frequency Division

The CD4018BF/3 fits frequency-divider designs that derive a lower periodic signal from an external clock. Its counter and divide-by-N architecture permits the divide ratio to be established through the preset and data connections, while the 10 MHz typical operating point at 10 V provides useful margin for moderate clock rates. The fully static CMOS implementation also avoids unnecessary state changes when the clock remains idle. In implementation, the designer must verify clock pulse width, propagation delay, feedback-loop timing, and the settling behavior of the preset inputs against the required output accuracy.

🏭

Event and Pulse Counting

CD4018BF/3 is appropriate for counting discrete events such as sensor pulses, machine movements, or timed production steps. The binary counter state can be observed through its decode outputs, and the preset capability allows a cycle to begin from a selected count instead of zero. Its medium-speed operation, with a typical 10 MHz maximum at a 10 V supply, is substantially faster than many mechanical-contact applications require. Designers should still account for switch bounce, input conditioning, reset timing, and the maximum tolerated event rate when interpreting the counter output.

⏱️

Programmable Timing Control

The CD4018BF/3 can act as the timing core in programmable delay and repetitive-sequence circuits. Preset values establish the starting count, while external decode and feedback logic can detect a terminal count and restart or gate the timing cycle. Its 5 V, 10 V, and 15 V parametric ratings support several industrial logic environments, and fully static operation maintains a stable count when the clock is stopped. Accurate timing requires checking propagation delay, clock pulse width, preset and reset recovery intervals, and the behavior of any external feedback combinational logic.

🔧

Digital Instrumentation

CD4018BF/3 suits digital instrumentation that must count samples, events, or timing intervals and present a decoded state. The 16-lead hermetic ceramic dual-in-line package is appropriate for through-hole instrument construction and provides a -55 °C to +125 °C rated operating range. The counter’s preset inputs can support calibration or selectable measurement intervals, while its outputs can drive display-control or status logic. Because this is a legacy CMOS counter, engineers should validate noise margins, clock-source edge quality, supply bypass behavior, and state transitions across the complete voltage and temperature range.

🏭

Industrial Sequence Control

The CD4018BF/3 can support legacy industrial sequence-control systems where a repeatable count drives discrete process steps. Its fully static operation preserves the count between clock events, and the preset function allows different sequence lengths without rebuilding the counter hardware. The through-hole CDIP-16 package facilitates repair and replacement in older control equipment. Integration requires careful inspection of reset priority, preset loading, unused-input states, and recovery timing. Designers should also confirm that the supply rail and all connected logic operate at compatible CMOS levels to prevent false clocking or incomplete count transitions.

⚡

Modulo Counter and Retriggerable Timer

CD4018BF/3 is useful in modulo-count and retriggerable-timer arrangements because the preset function permits a defined count range while external logic detects and reloads the terminal state. Its medium-speed operation supports clock sources significantly faster than typical industrial timing intervals, and its single-supply CMOS construction simplifies integration with 5 V, 10 V, or 15 V logic systems. To obtain repeatable timing, the feedback path must not introduce race conditions, and clock, reset, and preset recovery times must be respected. Pull-up or pull-down treatment of unused inputs is also necessary for deterministic operation.

What is the CD4018BF/3?
The CD4018BF/3 is a Harris Corporation CMOS presettable binary counter and divide-by-N circuit in a 16-lead hermetic ceramic dual-in-line package. According to the manufacturer datasheet information, the device supports medium-speed operation with a typical maximum frequency of 10 MHz at a 10 V supply, fully static operation, and standardized symmetrical output characteristics.
What is the maximum operating frequency of CD4018BF/3?
The CD4018BF/3 has a typical maximum operating frequency of 10 MHz when operated from a 10 V supply. The manufacturer datasheet describes this as medium-speed operation. Actual timing in a completed circuit also depends on clock pulse width, propagation delay, reset and preset timing, supply voltage, and the loading applied to the outputs.
What supply voltages support the CD4018BF/3?
The CD4018BF/3 is characterized at 5 V, 10 V, and 15 V supply levels. These ratings correspond to the manufacturer’s standard CMOS parametric test conditions and allow operation from low-voltage 5 V systems through 15 V logic systems. The maximum input current specification of 1 µA at 18 V also identifies the upper test condition used in the datasheet.
Where can I download the CD4018BF/3 datasheet PDF?
The CD4018BF/3 datasheet can be located through the Harris datasheet page at https://www.datasheets.com/harris/cd4018bf. The manufacturer-family information is also available through Texas Instruments at https://www.ti.com/lit/gpn/CD4018B. Use the pin-description and timing tables in the manufacturer datasheet when creating the schematic, assigning inputs, and determining the clock and reset constraints.
Where can I find the CD4018BF/3 pinout?
The CD4018BF/3 pinout is defined in the CD4018B manufacturer datasheet for its 16-lead ceramic dual-in-line package. Use the terminal-description table to map clock, reset, preset, data, decode, power, and ground connections. The target part is a CDIP-16 device, so a 16-pin SOIC or TSSOP alternative cannot be substituted without changing the board footprint.
Can CD4018BF/3 operate as a divide-by-N counter?
Yes. The CD4018BF/3 is designed to function as a presettable counter and divide-by-N circuit. By combining its count inputs with suitable feedback logic, the divide ratio can be established for timing, rate conversion, or periodic-event applications. The final operating frequency must remain consistent with the device’s 10 MHz typical maximum at a 10 V supply.
Is the CD4018BF/3 suitable for industrial control systems?
The CD4018BF/3 is suitable for many industrial control and instrumentation functions because it is a fully static CMOS counter with a -55 °C to +125 °C operating temperature range. Its hermetic 16-lead ceramic package is also mechanically suitable for through-hole assembly. Input levels, reset behavior, noise margins, and timing margins still require validation within the final industrial system.
Where can I buy CD4018BF/3 online?
Use the Request a Quote form on this page to request CD4018BF/3 availability, current lead time, and minimum order quantity. The exact /3 ordering suffix should be entered in the request so the distributor channel can confirm the correct Harris Corporation ceramic CDIP variant rather than a related CD4018-family package or grade.
What is the price of CD4018BF/3?
The current commercial price for CD4018BF/3 is best requested through the Request a Quote form on this page. The quote request should identify the exact MPN CD4018BF/3, the required quantity, and the acceptable packaging or delivery conditions. This avoids confusion with CD4018BF, CD4018BE, and surface-mount CD4018-family variants.
Is CD4018BF/3 in stock and what is its lead time?
Stock and lead time for CD4018BF/3 should be confirmed through the Request a Quote form on this page. Because CD4018BF/3 is a legacy-ordering variant, provide the quantity and target delivery date with the request. The exact suffix /3 is important when asking for confirmation of the Harris ceramic CDIP part.
What can replace CD4018BF/3?
The closest replacement must use the same 16-lead CDIP footprint and provide equivalent clock, reset, preset, data, and decode functions. No additional drop-in alternatives can be confirmed from the published cross-reference results, so engineers should not assume that a 16-pin SOIC or TSSOP CD4018-family device is pin-to-pin compatible. The manufacturer-family datasheet should be used to validate any proposed substitute.
Is CD4018BF/3 the same as CD4018BF?
CD4018BF/3 is the specified Harris Corporation ordering variant of the CD4018B counter family, while CD4018BF is a related CD4018B ordering designation. The exact manufacturer ordering table should be checked for grade, package, and qualification differences before treating them as interchangeable. A board designed for CD4018BF/3 requires a physical 16-lead ceramic dual-in-line footprint.
CD4018BF/3 vs CD4018BM - which is better for a CDIP design?
CD4018BF/3 is the relevant choice for a design using the target 16-lead ceramic dual-in-line footprint. CD4018BM is identified in the published comparison result as a 16-pin SOIC device, so it requires a different PCB footprint and is not a physical drop-in replacement for CD4018BF/3. Its logic function may be related, but package compatibility makes it unsuitable for direct substitution.
When should I choose CD4018BF/3 over another counter?
Choose CD4018BF/3 when the design requires a presettable CMOS counter or divide-by-N function, a 10 MHz typical operating point at 10 V, and a 16-lead ceramic dual-in-line footprint. It is particularly appropriate for through-hole industrial, instrumentation, and timing systems that retain a CD4018B counter design. Choose a modern counter instead when smaller PCB area, lower supply current, or newer qualification is more important than footprint continuity.
Is CD4018BF/3 suitable for frequency division and timing?
The CD4018BF/3 is suitable for frequency division and timing because it combines counter operation with programmable preset inputs and a typical maximum frequency of 10 MHz at a 10 V supply. Designers should establish the desired divide ratio, then verify propagation delay, clock pulse width, preset recovery time, and reset recovery time in the manufacturer timing diagrams. External feedback also requires deliberate design for a stable terminal count.

工程參考資料,適用於 CD4018BF/3 — 比較、設計指引及合規資訊。

選型指南

Choose CD4018BF/3 when maintaining a through-hole design built around the Harris CD4018B counter is more important than adopting a modern small-footprint device. It is a practical choice for legacy frequency dividers, programmable timers, event counters, and industrial sequence-control systems that need a presettable divide-by-N function and can operate within the CD4018B timing and voltage limits. Choose CD4018BM only when the PCB can be changed to a 16-pin SOIC footprint. Do not treat a generic CD4018 counter as a direct replacement unless its exact ordering suffix confirms the same CDIP package, terminal arrangement, operating ratings, reset behavior, and preset logic. For new designs with severe area, power, or qualification constraints, evaluate a current counter family and redesign the board rather than forcing this legacy ceramic part into a new platform.

與替代品比較

參數 本產品
Package 16-lead hermetic ceramic dual-in-line package
Brand Harris Corporation
Product Type CMOS presettable binary counter and divide-by-N circuit
Logic Family CD4000-series CMOS
Maximum Operating Frequency 10 MHz typical at 10 V
Parametric Supply Ratings 5 V, 10 V, and 15 V
Maximum Input Current 1 µA at 18 V
Operating Temperature Range -55 °C to +125 °C
Fully Static Operation Yes
Lead Count 16 leads

主要差異化特點

  • Matches the original CD4018B counter function in a hermetic ceramic CDIP package (對比CD4018BM)
  • Supports medium-speed counting at a 10 V supply (對比CD4018BF)
  • Provides a defined set of operating and environmental ratings (對比CD4018B types with unspecified ordering suffix)

設計說明

Treat clock, reset, and preset signals as a coordinated timing system. Check the manufacturer’s clock-pulse-width and recovery-time diagrams before choosing a feedback network, and ensure that preset data is stable before the active clock edge. A decoded terminal count must not create a combinational feedback path that retriggers or advances the counter more than once per intended cycle.

Use the manufacturer’s 16-lead CDIP pin orientation and preserve adequate clearance between adjacent ceramic-package leads. Place any local supply bypass close to the device’s power and ground connections, and route clock and reset traces away from noisy switching nodes. A conventional through-hole footprint is required; SOIC and TSSOP CD4018-family devices are not footprint-compatible with the target.

Operate the counter from a supply compatible with its 5 V, 10 V, and 15 V parametric ratings. Input levels must not exceed the limits for the selected supply because excessive input voltage can damage the input structures, while undershoot can create unintended clocking. Verify the absolute maximum input and supply ratings in the manufacturer datasheet before connecting external signals.

Keep the external clock source clean and use the shortest practical routing path for high-rate operation. Although the device is fully static when the clock is inactive, slow or noisy edges can create multiple transitions inside the switching window. Confirm that the source amplitude, rise and fall characteristics, and return path satisfy the voltage and timing requirements of the selected supply.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The component is a legacy Harris Corporation 16-CDIP counter. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established from the cited manufacturer-family information and must be confirmed for the exact ordering variant.

資料驗證日期: 2026-11-19 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

CD4018BF/3 datasheet CD4018BF/3 pinout CD4018BF/3 datasheet pdf CD4018BF/3 equivalent CD4018BF/3 replacement CD4018BF/3 cross reference CD4018BF/3 CDIP-16 footprint CD4018BF/3 10 MHz counter CD4018BF/3 divide by N CD4018BF/3 price CD4018BF/3 stock Harris CD4018BF/3 CD4018BF/3 vs CD4018BM CD4018BF/3 presettable counter

相關元件與詞彙

Harris Corporation CD4018BF/3 CD4018BF CD4018BM CD4018B CD4000 CMOS series presettable counter binary counter divide-by-N circuit CMOS logic fully static operation counter divider sequential logic frequency divider programmable timer industrial sequence control digital instrumentation hermetic ceramic dual-in-line package CDIP-16 through-hole mounting 10 MHz operating frequency preset inputs decode outputs symmetrical output characteristics
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情