Renesas Electronics

ISL81486IU - 5V 40Mbps RS-485/RS-422 Transceiver | Renesas

MPN: ISL81486IU ✓ 啟用中
5 V Vdss RS-485 and RS-422 Rds(on) 8-pin MSOP Package
MOQ: 1 |

ISL81486IU 概覽

Renesas Electronics ISL81486IU is a 5 V, half-duplex RS-485/RS-422 transceiver rated for data rates up to 40 Mbps and supplied in an 8-pin MSOP package. It combines a balanced bus driver and differential receiver in one 8-pin device, making it suitable for high-speed industrial communication links that require both RS-485 and RS-422 operation.

A transceiver is an interface circuit that converts logic-level transmit and receive signals into balanced differential bus signals, then reconstructs the received signal. The ISL81486IU belongs to the RS-485/RS-422 interface IC hierarchy, where differential signaling improves noise immunity and allows reliable data transfer over longer cables than conventional single-ended interfaces.

Key features include a 5 V supply, operation up to 40 Mbps, support for PROFIBUS, and BiCMOS circuit technology. These characteristics suit industrial automation, factory equipment, PROFIBUS nodes, process-control equipment, and other systems that combine long cable runs with demanding data rates. Its half-duplex architecture supports one driver and one receiver in a shared eight-pin package.

The device is designed to conserve board space compared with separate driver and receiver packages. The MSOP outline also supports dense industrial-control assemblies, although exposed-pad thermal performance and PCB copper must be considered when the device dissipates substantial power. Differential bus routing, controlled impedance, and proper termination remain central to achieving reliable operation at the upper end of its 40 Mbps capability.

Typical uses include high-speed RS-485 links in factory automation, RS-422 point-to-point links, PROFIBUS-compatible equipment, industrial controllers, data-acquisition systems, and communication interfaces operating from a 5 V rail. Because the bus topology determines correct operation, the network should use twisted-pair cabling, appropriate termination, and a common reference strategy between connected nodes.

Designers should follow the manufacturer datasheet for the exact pin assignment, enable and receiver-enable behavior, driver output levels, receiver thresholds, and recommended external components. The part number suffix IU identifies the specified package/order configuration, but the package drawing and pin description should always be checked against the exact ordering code before PCB release.

This page organizes the device’s interface role, package constraints, application fit, and verified ordering information into a design-oriented overview. It also distinguishes true same-package alternatives from parts that may only offer similar electrical functions, helping engineers assess PCB reuse without overlooking protocol, speed, or enable-control differences.

直接替換替代品,適用於 ISL81486IU — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: ISL81486IU (相同外形與佔位) — 差異在於 Maximum Data Rate, Package, Product Type.

Renesas Electronics
Maximum Data Rate: 30 Mbps
Package: 8-pin MSOP, 0.118 in (3.00 mm) width
Product Type: Single RS-485/RS-422 line transceiver
比較對象 ISL81486IU →

ISL81486IUZ

✅ 直接替換
📦 8-pin MSOP
Same 8-pin MSOP RS-485/RS-422 function and 5 V supply; ordering suffix differs and some electrical characteristics may vary.

📋 參考替代品(不在目錄中)

ISL81486IU-T

✅ 直接替換
📦 8-pin MSOP
Same ISL81486 family, 8-pin MSOP footprint, and 5 V interface function; packaging order code differs.

📋 參考替代品(不在目錄中)

ISL81485IU

✅ 直接替換
Renesas Electronics
📦 8-pin MSOP
Single RS-485/RS-422 line transceiver · 5 V · 30 Mbps · RS-485 and RS-422 · BiCMOS · 1 · 8-pin MSOP, 0.118 in (3.00 mm) width · Surface mount

聯絡詢價

查看資料表 →

ISL4486IU

✅ 直接替換
📦 8-pin MSOP
Related 5 V BiCMOS transceiver in the same 8-pin MSOP family; exact pin functions and timing differences require comparison.

📋 參考替代品(不在目錄中)

ISL83072EIUZA-T

✅ 直接替換
📦 8-pin MSOP
Same-package Renesas interface candidate with a 5.5 V listing maximum; data rate, supply, and enable logic differ from the 5 V 40 Mbps target.

📋 參考替代品(不在目錄中)

ISL81486IU 規格

Product Type RS-485/RS-422 half-duplex transceiver
供應電壓 5 V
Maximum Data Rate 40 Mbps
Supported Standards RS-485 and RS-422
PROFIBUS Support Yes
Circuit Technology BiCMOS
Transceiver Configuration 1 transmitter and 1 receiver
Duplex Mode Half-duplex
封裝 8-pin MSOP
腳位數 8 pins

ISL81486IU 8-pin msop 腳位配置指南

ISL81486IU(8-pin msop 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

ISL81486IU 的 8-pin msop 封裝腳位圖

無詳細腳位定義資料: ISL81486IU.

請參閱 資料表 以查看完整腳位配置。

典型應用

ISL81486IU 適用於 6 應用s: PROFIBUS Industrial Communication, High-Speed RS-485 Bus, Point-to-Point RS-422 Link, Factory Automation Controller, Industrial Data Acquisition, Instrumentation and Test Equipment.

🏭

PROFIBUS Industrial Communication

The ISL81486IU fits PROFIBUS interface nodes because the manufacturer identifies the device as a 5 V, ultra-high-speed PROFIBUS, RS-485/RS-422 transceiver with operation up to 40 Mbps. Its integrated driver and receiver provide the balanced physical layer for controllers, sensors, actuators, and industrial I/O modules connected to a PROFIBUS segment. In this topology, the transceiver converts logic signals into a differential bus waveform and receives the corresponding differential input. The high-rate capability provides useful timing margin for short, well-controlled industrial segments, although actual PROFIBUS compliance also depends on network length, cable type, termination, connector wiring, and device-level timing. Engineers should preserve the balanced pair as a routed differential pair, apply the network’s prescribed termination, and verify grounding and common-mode behavior across the complete segment.

🌐

High-Speed RS-485 Bus

The ISL81486IU is appropriate for a 5 V RS-485 bus that needs substantially more signaling speed than conventional low-rate transceivers. Its stated 40 Mbps capability supports short, point-to-point or lightly loaded multipoint links where propagation delay and skew remain manageable. The balanced differential driver and receiver improve rejection of common-mode noise compared with a single-ended interface, while the half-duplex arrangement allows the same pair of conductors to carry data in either direction. For a robust implementation, place termination only where required by the topology, avoid excessive stub lengths, route the differential pair over a continuous reference plane, and test the assembled cable and transceiver combination. These practices are especially important because a transceiver rated for 40 Mbps does not guarantee that every cable, connector, and grounding arrangement can preserve that rate.

🔧

Point-to-Point RS-422 Link

The ISL81486IU can serve as the physical-layer device in a point-to-point RS-422 connection where a source drives a remote receiver over a twisted pair. RS-422 is suited to one-to-one communication and balanced signaling, and the transceiver’s stated 40 Mbps rate allows short links to operate with substantial bandwidth margin. The device combines the balanced transmitter and receiver in an 8-pin MSOP, reducing the footprint compared with separate interface packages. In a practical link, terminate the receiving end in accordance with the selected network strategy, keep the cable pair tightly twisted, and provide a suitable reference connection if the source and receiver grounds are not locally common. Engineers should also evaluate propagation delay, skew, input thresholds, and maximum cable length from the manufacturer electrical tables before treating the link specification as complete.

🏭

Factory Automation Controller

The ISL81486IU is well suited to compact factory-automation controllers that exchange high-speed data with remote modules over balanced industrial wiring. Its 5 V supply fits many embedded control assemblies, while the 40 Mbps capability supports communication links whose timing must remain predictable inside equipment racks or across short machine distances. The 8-pin MSOP package allows the interface to be placed near a connector or processor without occupying the board area of two separate line-interface devices. Designers should keep the driver and receiver traces symmetrical, provide local supply decoupling, and keep protection or isolation components outside the high-speed differential path unless their propagation delay has been included in the system budget. Industrial enclosure grounding and surge protection remain separate from logic functionality and should be engineered for the installation environment.

📊

Industrial Data Acquisition

The ISL81486IU can form the communications link in a data-acquisition system that distributes measurements from remote sensors or machine controllers. Balanced differential signaling helps maintain data integrity when the acquisition cabinet is connected to field equipment through cables that may pick up industrial noise. The transceiver’s 40 Mbps capability is valuable when the acquisition backplane must carry bursts of data, synchronize equipment, or support a multi-drop bus with short branches. The device should be placed near the protected cable entry point, with its differential route separated from switching power and motor-control traces. Add termination and biasing according to the selected network configuration, and verify common-mode limits for every connected node. A logic-level analysis at the transceiver pins is often more informative than relying only on a bus analyzer when diagnosing installation-specific signal-integrity problems.

🖥️

Instrumentation and Test Equipment

The ISL81486IU is appropriate for instrumentation modules that require a compact, high-speed balanced communication interface. Test and measurement equipment often connects an instrument to a remote fixture, controller, or workstation over a cable that extends beyond the enclosure. The 5 V transceiver can preserve data integrity in that environment through differential signaling, while its 40 Mbps capability supports dense measurement data and low-latency control traffic. The MSOP footprint is especially useful in multi-channel instruments where each channel may require a communications interface. Layout should provide a short path from the transceiver to the connector, avoid splitting the differential pair around other circuitry, and maintain a continuous ground reference. If the instrument can be connected to equipment at different ground potentials, add an appropriate isolation strategy rather than assuming the transceiver's common-mode limits will cover every installation.

推薦產品摘要

ISL81485IU Renesas Electronics 用於: PROFIBUS Industrial Communication, Point-to-Point RS-422 Link, Industrial Data Acquisition ISL4486IU Related high-speed balanced transceiver 用於: PROFIBUS Industrial Communication, High-Speed RS-485 Bus, Factory Automation Controller, Instrumentation and Test Equipment ISL81486IUZ Same-family ordering alternative 用於: High-Speed RS-485 Bus, Industrial Data Acquisition ISL83072EIUZA-T Same-package interface candidate 用於: Point-to-Point RS-422 Link, Instrumentation and Test Equipment ISL81486IU-T Same-family ordering alternative 用於: Factory Automation Controller
What is the operating voltage of ISL81486IU?
The ISL81486IU operates from a 5 V supply. According to the manufacturer datasheet, the device combines a differential line driver and receiver in a single 8-pin MSOP package. The supply rating and the broad transceiver description identify it as a 5 V RS-485/RS-422 interface rather than a 3.3 V device. Confirm power sequencing, decoupling, and absolute-maximum limits against the exact datasheet before applying the part.
What is the maximum data rate of ISL81486IU?
The ISL81486IU supports data rates up to 40 Mbps. The manufacturer describes the ISL4486 and ISL81486 families as 5 V BiCMOS transceivers with larger output voltage and a higher data rate of 40 Mbps for demanding PROFIBUS and high-speed balanced links. At the highest rates, cable length, propagation delay, termination, skew, and PCB routing become increasingly important, so the complete channel should be validated rather than only the driver.
Which communication standards does ISL81486IU support?
The ISL81486IU supports both RS-485 and RS-422 balanced communication. The manufacturer datasheet identifies the part as a 5 V, ultra-high-speed PROFIBUS, RS-485/RS-422 transceiver. RS-485 is commonly used for multipoint buses, while RS-422 is commonly used for point-to-point links. Because both interfaces use differential signaling, termination and biasing must be designed for the actual bus topology.
Where can I download the ISL81486IU datasheet PDF?
The ISL81486IU datasheet is available through the manufacturer-hosted document and the listed datasheet download pages for this part. The document covers the 5 V supply, 40 Mbps capability, RS-485/RS-422 operation, electrical characteristics, pin descriptions, and application information. Use the ISL81486IU document for the IU ordering configuration and verify the package drawing against the PCB footprint before release.
Where can I find the ISL81486IU pinout?
The ISL81486IU pinout is defined in the pin-description section and package drawing of the manufacturer datasheet for the 8-pin MSOP package. Use that table when assigning the differential bus pins, supply, ground, driver-enable, and receiver-enable functions. Pin names and electrical directions should be transcribed directly from the datasheet rather than inferred from another ISL81486 ordering code, since suffix variants can differ in orderable packaging details.
Is the ISL81486IU suitable for PROFIBUS equipment?
Yes, the ISL81486IU is specifically identified as a PROFIBUS-capable, ultra-high-speed RS-485/RS-422 transceiver. Its 5 V operation and data-rate capability up to 40 Mbps align with high-speed industrial communication requirements. PROFIBUS implementation also depends on correct bus termination, cable characteristics, connector pin assignments, isolation strategy, grounding, and compliance with the applicable network specification.
What is the difference between ISL81486IU and ISL81486IUZ?
The ISL81486IU and ISL81486IUZ both identify 8-pin MSOP RS-485/RS-422 transceivers, with the suffix difference primarily distinguishing ordering and packaging configurations. The cross-reference listing describes them as similar parts with broadly consistent functional characteristics, while warning that some electrical details differ. Confirm the ordering table, tape-and-reel presentation, and full electrical comparison before treating one suffix as a production substitute.
What is the best drop-in replacement for ISL81486IU?
The closest drop-in candidates must retain the 8-pin MSOP footprint, RS-485/RS-422 function, 5 V supply, and approximately 40 Mbps data-rate capability. ISL81486IUZ and ISL81486IU-T are same-brand ordering candidates, while ISL81485IU and ISL4486IU require closer verification of enable logic and bus performance. No substitute should be approved solely from package shape; confirm pinout, thresholds, propagation delay, and driver output behavior against the datasheet.
Can ISL81486IU replace ISL81485IU?
The ISL81486IU can be considered as a replacement candidate for the ISL81485IU because both are listed as 8-MSOP RS-485 interface devices, but the replacement is conditional on pin-level and timing verification. The ISL81485IU is a related family member and is listed as obsolete, while the ISL81486IU offers the explicitly stated 40 Mbps capability. Compare enable polarity, receiver enable, driver outputs, supply current, and fail-safe behavior before production use.
When should I choose ISL81486IU over a lower-speed RS-485 transceiver?
Choose the ISL81486IU when the bus must operate at high data rates or when a PROFIBUS-oriented, 5 V RS-485/RS-422 interface is required. Its stated capability of 40 Mbps provides margin compared with conventional low-speed transceivers, while the combined driver and receiver reduce board area. A lower-speed part may be preferable only when its published limits comfortably exceed the actual channel requirement and offer a clear cost or feature advantage.
What can replace ISL81486IU?
ISL81486IUZ, ISL81486IU-T, ISL81485IU, ISL4486IU, and ISL83072EIUZA-T are the identified same-package candidates for evaluation. A valid replacement must preserve the 8-pin MSOP land pattern, 5 V operation, balanced driver and receiver functions, and required throughput. The candidates differ in exact features and timing, so use the manufacturer comparison information and verify every connected pin before approving a substitution.
Is ISL81486IU the same as ISL4486IU?
No, the ISL81486IU and ISL4486IU are related members of the same 5 V BiCMOS high-speed transceiver family, but they are not automatically identical. The manufacturer describes both in the ISL4486/ISL81486 family, while the ordering and application details can differ. Both use an 8-pin MSOP format, yet exact pin functions, enable control, data rate, and operating characteristics should be compared before substitution.
Where can I buy ISL81486IU and check its lead time?
Use the Request a Quote form on this page to ask for ISL81486IU availability, MOQ, and current lead time. The form is the appropriate route for a firm order commitment because inventory and lead time can change independently of the device specification. Provide the exact ISL81486IU ordering code, required quantity, target date, and destination country so the supply response reflects the intended production build.
Is ISL81486IU in stock?
Current stock for ISL81486IU should be confirmed through the Request a Quote form on this page. A distributor listing showing an order button does not by itself guarantee a current stock quantity, and this page does not publish a static inventory claim. Include your required quantity and production schedule in the request so the supplier can confirm allocation, lifecycle status, and the earliest possible shipment.
What are the key specifications of ISL81486IU that engineers should know?
The key ISL81486IU specifications are 5 V operation, a maximum data rate of 40 Mbps, one driver and one receiver in a half-duplex configuration, and an 8-pin MSOP package. The manufacturer also identifies BiCMOS technology and PROFIBUS, RS-485, and RS-422 applications. Because this legacy device appears in multiple order configurations, engineers should verify the exact suffix, pinout, enable behavior, and absolute-maximum ratings in the manufacturer datasheet.

工程參考資料,適用於 ISL81486IU — 比較、設計指引及合規資訊。

選型指南

Choose the ISL81486IU for a 5 V RS-485/RS-422 interface that needs a compact 8-pin MSOP solution and a stated data rate up to 40 Mbps, particularly in PROFIBUS-oriented industrial equipment. Select ISL81486IUZ or ISL81486IU-T when the ordering configuration satisfies procurement and assembly requirements; verify the suffix-specific datasheet and delivery format. Consider ISL4486IU only after comparing its exact pin functions, enable logic, and timing with the ISL81486IU. Evaluate ISL81485IU for related 8-MSOP designs when its published data rate and control behavior meet the system requirement. ISL83072EIUZA-T is a lower-confidence same-package candidate because its supply and timing details must be checked against the target. For any replacement, approve the part only after confirming the pinout, differential thresholds, propagation delay, supply current, fail-safe behavior, and operation on the intended cable and termination network.

與替代品比較

參數 本產品 ISL81486IUZ ISL81486IU-T ISL81485IU ISL4486IU ISL83072EIUZA-T
Package 8-pin MSOP 8-pin MSOP 8-pin MSOP 8-pin MSOP 8-pin MSOP 8-pin MSOP
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Ordering Configuration ISL81486IU ISL81486IUZ suffix ISL81486IU-T suffix ISL81485IU suffix ISL4486IU suffix ISL83072EIUZA-T suffix

主要差異化特點

  • Higher stated bus rate for high-speed industrial links (對比ISL81485IU)
  • Purpose-built 5 V BiCMOS high-speed balanced interface (對比ISL83072EIUZA-T)
  • Integrated PROFIBUS-oriented driver and receiver in a compact package (對比ISL4486IU)
  • Closest ordering alternatives preserve the 8-pin MSOP footprint (對比ISL81486IUZ)

設計說明

Route the differential bus as a tightly coupled pair over a continuous ground plane, keeping the two traces at a matched length where channel skew matters. Place the transceiver close to the connector or protected board edge, and avoid routing the pair through test pads, stubs, or layers that interrupt coupling. Keep switching regulators, relays, and high-current traces away from the bus path. At rates approaching 40 Mbps, connector and cable discontinuities can be more damaging than the apparent rise time of the IC.

Do not assume that every part sharing the 8-pin MSOP outline is electrically interchangeable. Compare supply limits, driver enable and receiver enable polarity, receiver thresholds, propagation delay, fail-safe behavior, and bus-output states before substitution. In particular, the ISL81485IU and ISL83072EIUZA-T candidates may use the same land pattern while differing in timing or control behavior. Record the exact manufacturer ordering suffix and test bus idle, dominant, turnaround, and receive states on assembled hardware.

Use a low-impedance 5 V supply with local high-frequency decoupling placed close to the device’s supply and ground pins. Determine the actual supply-current requirement from the manufacturer electrical tables for the selected operating mode, driver state, and load. Account for line-driver dissipation and connector/cable loading in the power budget. If protection components are added for industrial surge or ESD requirements, include their capacitance and leakage in the high-speed timing and common-mode analysis.

Design termination and any biasing network for the actual network topology rather than adding both indiscriminately. In a point-to-point RS-422 link, the receiver is commonly the terminated endpoint; in a multidrop RS-485 network, termination is normally placed at the physical ends, and biasing provides a defined idle state where required. Validate propagation delay, inter-symbol interference, common-mode range, and connector reflections across the longest cable and fastest operating mode before production release.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The listed product pages do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for this ordering configuration.

相關搜尋

ISL81486IU datasheet ISL81486IU pinout ISL81486IU datasheet pdf ISL81486IU equivalent ISL81486IU replacement ISL81486IU cross reference ISL81486IU vs ISL81485IU ISL81486IU vs ISL4486IU Renesas ISL81486IU ISL81486IU MSOP pinout ISL81486IU PROFIBUS transceiver ISL81486IU price ISL81486IU stock ISL81486 application circuit

相關元件與詞彙

Renesas Electronics Intersil ISL81486IU ISL81486IUZ ISL81486IU-T ISL81485IU ISL4486IU ISL83072EIUZA-T RS-485 RS-422 PROFIBUS half-duplex transceiver differential line driver differential receiver BiCMOS 5 V transceiver 40 Mbps data rate 8-pin MSOP MSOP package family surface-mount package industrial automation balanced differential signaling common-mode rejection bus termination
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情