ISL81485IU - 30Mbps RS-485/RS-422 Transceiver | Renesas
MPN: ISL81485IU ✗ 停產ISL81485IU 概覽
An RS-485/RS-422 transceiver is an interface IC that converts single-ended digital signals into balanced differential signals for transmission and converts received differential signals back into a logic-level output. RS-422 is commonly associated with point-to-point, balanced communication, while RS-485 supports multipoint bus networks and driver inhibit capability. The ISL81485IU belongs to the broader hierarchy of interface transceivers, serial communication ICs, and semiconductors used to connect digital equipment over copper cabling.
The principal features of the ISL81485IU are its 5 V operation, 30 Mbps maximum signaling rate, and support for both RS-485 and RS-422 communication standards. Its single-transceiver format allows a compact design to implement a bidirectional link by connecting the driver and receiver controls to the same digital interface. The manufacturer datasheet describes a larger output voltage and higher data rate as beneficial for high-speed applications, while its BiCMOS process supports the demanding output and receiver requirements of balanced differential links.
In an RS-485 network, the differential bus reduces sensitivity to common-mode noise and allows data to be transmitted over longer cable runs than a conventional single-ended interface. The 30 Mbps capability makes the device relevant to factory automation, industrial control, data acquisition, and embedded instrumentation systems that need a compact point-to-point or multidrop communications interface. When two transceivers are used on a shared bus, driver-enable and receiver-enable controls determine which node drives or listens at any given time.
The principal design tradeoff is that a high-speed differential transceiver requires careful attention to board layout, termination, decoupling, grounding, and protection. The 5 V supply should be filtered near the device, and routed differential traces should remain closely coupled. Cabling and connector geometry also influence signal integrity, particularly at the maximum 30 Mbps operating rate.
This page combines the manufacturer specifications, interface-function analysis, sourcing fields, and practical RS-485/RS-422 design guidance to support component selection and PCB implementation. It also distinguishes confirmed drop-in candidates from related devices that require additional pin, timing, and protocol verification before substitution.
直接替換替代品,適用於 ISL81485IU — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ISL81485IU (相同外形與佔位) — 差異在於 Maximum Data Rate, Package, Product Type.
ISL81486IU
✅ 直接替換聯絡詢價
查看資料表 →ISL81485IU 規格
| Product Type | Single RS-485/RS-422 line transceiver |
| 供應電壓 | 5 V |
| Maximum Data Rate | 30 Mbps |
| Supported Standards | RS-485 and RS-422 |
| Process Technology | BiCMOS |
| Number of Transceivers | 1 |
| 封裝 | 8-pin MSOP, 0.118 in (3.00 mm) width |
| 安裝類型 | Surface mount |
| Signal Interface | Balanced differential |
ISL81485IU 8-pin msop, 0.118 in (3.00 mm) width 腳位配置指南
ISL81485IU(8-pin msop, 0.118 in (3.00 mm) width 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ISL81485IU.
請參閱 資料表 以查看完整腳位配置。
典型應用
ISL81485IU 適用於 3 應用s: 嵌入式系統, IoT 裝置, 工業控制.
嵌入式系統
使用 ISL81485IU 於嵌入式應用中進行核心處理。
IoT 裝置
由 ISL81485IU 驅動的智慧連網裝置。
工業控制
使用 ISL81485IU 的自動化與控制系統。
工程參考資料,適用於 ISL81485IU — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ISL81486IU |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 8-MSOP | 8-MSOP |
| Maximum Data Rate | 30 Mbps | 30 Mbps |
| Lifecycle Status | Obsolete | Obsolete |
| Mounting Type | Surface mount | Surface mount |
主要差異化特點
- High-speed balanced communications in a compact package (對比ISL81486IU)
- One device supports two balanced bus standards (對比ISL81486IU)
- Single-transceiver implementation reduces board area (對比ISL81486IU)
設計說明
Route the differential pair as a closely coupled pair with continuous reference-plane geometry and minimize stubs, vias, and branch points. At 30 Mbps, discontinuities and unbalanced loading can degrade the differential signal. Keep the transceiver close to the connector and place termination components near the bus interface so that reflections are controlled without creating long high-frequency current loops.
Decouple the 5 V transceiver supply close to the device and keep the return-current path continuous beneath the IC and connector. Use the manufacturer-recommended capacitance and voltage rating, and account for supply ripple when the bus reaches its maximum 30 Mbps data rate. Avoid sharing a narrow supply path with unrelated switching or motor-current loads.
Do not substitute the ISL81485IU-T as a different functional alternative; it represents a distinct ordering or packing suffix for the same ISL81485 device. Before fitting an alternative transceiver, compare pin names, enable polarity, receiver-enable behavior, propagation delay, bus impedance, common-mode range, and power-off state. A shared MSOP outline alone does not guarantee behavioral compatibility.
For RS-485 networks, use an appropriate topology and termination strategy rather than adding termination indiscriminately to every node. Stubs should be minimized, especially on high-speed networks. The differential interface can improve noise immunity, but common-mode transients still require appropriate protection and grounding, particularly where the transceiver is connected to long external cables.
合規資訊
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the available records. The ISL81485IU and ISL81486IU are identified as obsolete.