ISL8324IBZ - Dual SPST Analog Switch, 60 Ohm, 8-SOIC | Renesas
MPN: ISL8324IBZ ✓ 啟用中ISL8324IBZ 概覽
An analog switch is an interface IC that connects or disconnects signal paths under digital control. SPST means single-pole, single-throw: one input and one output form a controlled connection for each channel. The normally closed designation means the relevant path is connected before the control input changes state. Together, analog switch, SPST switch, multiplexer interface, and low-voltage switching IC describe the ISL8324IBZ's role within general-purpose interface and power-management electronics.
The headline characteristics are its two switch circuits, 60 ohm on-resistance, 1:1 signal routing, single-supply operation, and 8-SOIC package. The 60 ohm resistance is important when the switch drives a lightly loaded or high-impedance node because it limits the voltage-divider effect between the source and destination. The 1:1 configuration preserves signal polarity rather than inverting the selected signal, which simplifies routing in measurement, control, and embedded peripheral systems.
ISL8324IBZ belongs to the Renesas ISL8323-ISL8325 precision dual analog-switch family. Individual family members can differ in switch polarity, on-resistance, and control behavior, so an engineer should verify the complete pin description and electrical table before substituting one MPN for another. The IBZ ordering code specifically identifies the 8-pin SOIC configuration used in this part.
Typical uses include battery-powered measurement equipment, analog sensor routing, test and measurement systems, and embedded signal-path multiplexing. In each case, the switch can isolate or reconnect a signal node under firmware control. Battery-powered applications benefit from the single-supply operation, while the compact SOIC footprint supports conventional surface-mount assembly and routing in mixed-signal designs.
The principal design consideration is control-state compatibility. Because the ISL8324IBZ is normally closed, firmware and external pull resistors must be evaluated against the default signal path and the desired powered state. Designers should also account for the 60 ohm series resistance when calculating settling behavior, attenuation, and drive requirements for the connected load.
This page organizes the verified switch configuration, package details, application guidance, and engineering trade-offs in one searchable reference. It emphasizes how the dual-channel architecture, normally closed behavior, 1:1 routing, and 60 ohm resistance affect practical circuit decisions when replacing or selecting an analog switching component.
直接替換替代品,適用於 ISL8324IBZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ISL8324IBZ (相同外形與佔位) — 差異在於 Package, Switch Configuration, Number of Circuits, Switch Type.
ISL8323IBZ
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →ISL8325IBZ
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →ISL8324IBZ 最大額定值與電氣特性
| Number of Circuits | 2 |
| Switch Configuration | Dual SPST |
| Signal Routing | 1:1 |
| On-Resistance | 60 ohm |
| Switch State | Normally closed |
| Supply Type | Single supply |
| Minimum Supply Voltage | 1 V |
| Maximum Supply Voltage | 12 V |
| 封裝 | 8-SOIC |
| 腳位數 | 8 pins |
| 安裝類型 | Surface mount |
ISL8324IBZ 8-soic 腳位配置指南
ISL8324IBZ(8-soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ISL8324IBZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
ISL8324IBZ 適用於 6 應用s: Battery-Powered Sensor Routing, Analog Signal Multiplexing, Test and Measurement Systems, Embedded Peripheral Isolation, Low-Voltage Control Signal Routing, Precision Measurement Front Ends.
Battery-Powered Sensor Routing
The ISL8324IBZ fits battery-powered sensor systems because it combines two normally closed SPST channels with single-supply operation from 1 V to 12 V. Each channel can connect an analog sensor path to a shared measurement or processing node, allowing firmware to change which source is presented to the circuit. The 60 ohm on-resistance should be included when calculating signal attenuation, particularly with high-impedance sensor outputs. The 8-SOIC package also keeps the routing stage compact enough for space-constrained portable equipment.
推薦
Analog Signal Multiplexing
The two independent SPST circuits in the ISL8324IBZ allow a compact analog multiplexer arrangement for low-voltage instrumentation. With a 1:1 transfer configuration, the selected signal retains its polarity as it is routed to a downstream amplifier, converter, or measurement channel. The normally closed state also supports designs that need a connected default path. Because the device presents 60 ohm on-resistance, source and load impedances must be considered together to maintain the required measurement accuracy.
推薦
Test and Measurement Systems
ISL8324IBZ is appropriate for test and measurement equipment that needs to isolate, reconnect, or select low-voltage analog signals under instrument control. Its dual-channel structure can route two related nodes without duplicating the switching stage, while the 8-SOIC package supports conventional PCB layout practices. Designers should account for the 60 ohm path resistance when calculating attenuation and settling, and should verify that the normally closed condition matches the instrument's expected idle state.
推薦
Embedded Peripheral Isolation
The ISL8324IBZ can isolate two embedded peripheral paths from a shared bus or analog section while maintaining a defined default connection. Its single-supply range of 1 V to 12 V suits low-voltage embedded systems, and the dual architecture controls two paths independently. Firmware must deliberately account for the normally closed behavior at startup and during reset. The 60 ohm on-resistance also makes the switch most appropriate for high-impedance nodes rather than low-ohm power or high-current loads.
推薦
Low-Voltage Control Signal Routing
The ISL8324IBZ can route low-voltage control or feedback signals between a controller and external circuitry while providing a 1:1 transfer path. Two normally closed channels can support paired functions such as enable and feedback routing, although each channel still requires the correct default-state treatment in firmware. The 8-SOIC footprint is practical for compact control boards, and single-supply operation allows the switch to share a low-voltage rail. The 60 ohm resistance is acceptable when the receiving input impedance is much higher.
推薦
Precision Measurement Front Ends
The ISL8324IBZ fits precision measurement front ends where a source must be disconnected from an amplifier or converter during another measurement. The dual SPST arrangement supports two controlled routing decisions in one 8-SOIC package, and the 1:1 configuration preserves signal polarity. The 60 ohm on-resistance can create an error with finite-impedance sources, so include it in the front-end noise-gain and attenuation calculation. Firmware should also respect the normally closed default connection to prevent unintended source loading.
推薦
推薦產品摘要
工程參考資料,適用於 ISL8324IBZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Number of Circuits | 2 |
| Switch Configuration | Dual SPST |
| Signal Routing | 1:1 |
| On-Resistance | 60 ohm |
| Switch State | Normally closed |
| Supply Configuration | Single supply |
| Supply Voltage Range | 1 V to 12 V |
| Package | 8-SOIC |
| Brand | Renesas Electronics |
| Mounting Type | Surface mount |
主要差異化特點
- Two independently controlled analog paths in one package (對比Single-channel analog switch alternatives)
- Defined normally closed default path (對比Normally open analog switch alternatives)
- Low-voltage single-supply operation (對比Higher-voltage dual-supply switch alternatives)
設計說明
Treat the ISL8324IBZ as a normally closed device when designing reset states and control logic. The default closed path can connect an external signal to the downstream circuit before firmware asserts the desired state. Add the appropriate pull resistor so the control input remains in a defined condition during power-up, reset, and brownout, then verify that every connected node can tolerate the default connection.
Include the 60 ohm on-resistance in the source-to-load model. For a voltage source with finite output resistance and a receiving input with finite input resistance, the switch contributes to the voltage divider and can alter gain or measurement accuracy. Use high-impedance receivers where possible, and evaluate settling behavior when the connected node has appreciable capacitance. This is especially important for precision measurement rather than logic-level routing.
Place the ISL8324IBZ close to the analog nodes being switched to minimize trace resistance and susceptibility to injected noise. Route the two switch paths separately from fast digital and switching-converter nodes, maintain a continuous ground reference, and keep the control traces away from sensitive analog traces. Follow the manufacturer's pin-description table when assigning the 8-SOIC footprint and keep unused or reserved pins correctly terminated.
合規資訊
The verified product information does not state the requested environmental or material-compliance certifications.