KSZ8794CNXCC - 4-Port 10/100 Managed Ethernet Switch | Microchip
MPN: KSZ8794CNXCC ✓ 啟用中KSZ8794CNXCC 概覽
An Ethernet switch is a Layer 2 network component that receives Ethernet frames, examines destination addresses, and forwards traffic through the appropriate physical port. The KSZ8794CNXCC belongs to the managed-switch hierarchy, combining integrated 10/100 Base-T/TX PHYs with management features designed to reduce the component count and board area required for multiport industrial or embedded Ethernet equipment.
The principal features are four integrated copper Ethernet ports, a configurable Gigabit uplink, support for RGMII, MII, and RMII host interfaces, internal biasing, and on-chip termination. Its 8 mm by 8 mm QFN-64 package supports compact designs while exposing high-speed network connectivity without requiring four discrete Ethernet PHYs. The managed Layer 2 architecture is suitable for systems that need controlled forwarding behavior rather than only basic hub functionality.
The uplink architecture allows a lower-cost 10/100 Mb/s access network to connect to a faster Gigabit backbone through a single high-speed host interface. RGMII supports parallel high-speed signaling, MII is a lower-speed parallel interface, and RMII reduces the number of host-side signals. Designers should select the interface according to the host processor, signal-rate requirements, board constraints, and software-support considerations described in the manufacturer datasheet.
Typical uses include industrial Ethernet gateways, factory automation controllers, embedded network appliances, video-network equipment, and compact access switches. The KSZ8794CNXCC is especially relevant when three copper endpoints need 10/100 Mb/s connectivity and a fourth port must provide a Gigabit path to a network processor or switching uplink.
Board design requires careful treatment of Ethernet magnetics, termination, supply routing, clocking, and high-speed uplink signals. Place the KSZ8794CNXCC and its decoupling close to the relevant connectors, follow the hardware design checklist for RJ45 termination, and preserve continuous ground references beneath high-speed interfaces.
This product summary consolidates the switch configuration, interface options, package information, drop-in-family alternatives, and implementation guidance needed to evaluate the KSZ8794CNXCC before beginning a Layer 2 Ethernet design.
直接替換替代品,適用於 KSZ8794CNXCC — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: KSZ8794CNXCC (相同外形與佔位).
KSZ8794CNXIC
✅ 直接替換聯絡詢價
查看資料表 →KSZ8795CNXCC
✅ 直接替換📋 參考替代品(不在目錄中)
KSZ8794CNXCC 最大額定值與電氣特性
| Product Type | Layer 2 managed Ethernet switch |
| Number of Ports | 4 ports |
| Copper Port Configuration | 3 ports at 10/100 Mb/s and 1 Gigabit uplink at 10/100/1000 Mb/s |
| Uplink Interface | Gigabit RGMII/MII/RMII |
| Supported Host Interfaces | RGMII, MII, and RMII |
| Ethernet Standard | 10/100 Base-T/TX |
| Uplink Ethernet Rate | 10/100/1000 Mb/s |
| 供應電壓 | 3.3 V |
| Package Type | 64-pin QFN |
| Package Dimensions | 8 mm x 8 mm |
| 安裝類型 | Surface mount |
| Packaging Form | Tray |
| Internal Biasing | Integrated |
| On-Chip Termination | Integrated |
| Managed Layer | Layer 2 |
KSZ8794CNXCC 8 mm x 8 mm 腳位配置指南
KSZ8794CNXCC(8 mm x 8 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: KSZ8794CNXCC.
請參閱 資料表 以查看完整腳位配置。
典型應用
KSZ8794CNXCC 適用於 6 應用s: Industrial Ethernet Gateway, Factory Automation Controller, Embedded Network Appliance, Video Network Equipment, Compact Access Switch, Communication Equipment.
Industrial Ethernet Gateway
The KSZ8794CNXCC fits an industrial gateway that connects three 10/100 Mb/s local devices to a Gigabit network backbone. The managed Layer 2 switch provides controlled frame forwarding while the fourth port reaches a higher-speed network through RGMII, MII, or RMII. Operating from 3.3 V and using a compact 64-QFN, 8 mm by 8 mm package helps reduce board area in DIN-rail or embedded gateway products. The design should allocate copper, magnetics, and RJ45 protection according to Microchip’s hardware design checklist, particularly the 75-ohm, 1000 pF, 2 kV center-tap network.
推薦
Factory Automation Controller
The KSZ8794CNXCC can serve as the central Ethernet switch in a factory automation controller with three 10/100 Mb/s machine interfaces and one Gigabit uplink. Its managed Layer 2 operation is useful when the controller must forward frames between local equipment while maintaining a defined path to a supervisory network. The 3.3 V supply requirement and integrated copper PHYs reduce the external circuitry needed for a multiport design. Layout must preserve high-speed uplink routing, provide local decoupling, and maintain controlled chassis-return paths around every Ethernet transformer.
推薦
Embedded Network Appliance
The KSZ8794CNXCC is appropriate for an embedded appliance that exposes several low-speed service ports and a faster backbone connection. Three 10/100 Mb/s copper ports can serve management, status, or peripheral connections, while the 10/100/1000 Mb/s uplink links the appliance to a host processor over RGMII, MII, or RMII. Its integrated four-port architecture replaces a collection of discrete Ethernet interface blocks. Selection of the host interface should account for PCB area, processor support, timing, and software initialization requirements.
推薦
Video Network Equipment
The KSZ8794CNXCC can support video-network equipment that combines several 10/100 Mb/s management or sensor links with a Gigabit uplink. The three access ports provide economical connectivity for cameras, control panels, or monitoring nodes, while the Gigabit port carries consolidated traffic toward recording or aggregation equipment. The managed Layer 2 function gives the system a controlled forwarding architecture rather than shared collision-domain behavior. Ethernet magnetics, surge protection, and isolation must be selected to match the installation environment and EMC objectives.
推薦
Compact Access Switch
The KSZ8794CNXCC can form the core of a compact managed access switch with three 10/100 Mb/s endpoint ports and one Gigabit network port. This mixed-speed configuration is useful where field devices remain on 10/100 Mb/s while aggregation equipment requires 1 Gb/s. RGMII provides a high-throughput parallel host connection, whereas RMII can reduce host-side pin count when its timing and throughput requirements are acceptable. Firmware configuration should establish the desired forwarding, filtering, and management behavior without exceeding port or host-interface timing limits.
推薦
Communication Equipment
The KSZ8794CNXCC is suitable for communication equipment requiring a small number of copper Ethernet service ports and a Gigabit uplink to a network processor. Its three 10/100 Mb/s ports can connect management, configuration, or auxiliary equipment, while RGMII, MII, or RMII provides integration flexibility with different host architectures. The 64-QFN, 8 mm by 8 mm package supports compact boards, although careful fanout and exposed-pad layout remain essential. Signal-integrity review should cover uplink clocks, impedance-controlled traces, and return paths between the switch and magnetics.
推薦
推薦產品摘要
工程參考資料,適用於 KSZ8794CNXCC — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | KSZ8794CNXIC | KSZ8795CNXCC |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin QFN (8x8 mm) | 64-pin QFN (8x8 mm) | 64-pin QFN (8x8 mm) |
| Product Type | Layer 2 managed Ethernet switch | Layer 2 managed Ethernet switch | Managed Ethernet switch |
| Uplink Rate | 10/100/1000 Mb/s | 10/100/1000 Mb/s | Gigabit Ethernet support |
| Integrated Features | Internal biasing and on-chip termination | Internal biasing and on-chip termination | Additional Ethernet and advanced QoS-related features |
主要差異化特點
- Mixed-speed four-port integration (對比KSZ8795CNXCC)
- Multiple host-interface choices (對比KSZ8794CNXIC)
- Integration for compact Ethernet designs (對比KSZ8795CNXCC)
設計說明
Follow the Microchip KSZ8794CNX hardware design checklist when placing the switch, Ethernet magnetics, and protection components. The specified RJ45 transmit path connects pin 3 to TX+ and pin 6 to TX−, with the cable-side center tap terminated through a 75-ohm resistor and a 1000 pF, 2 kV capacitor to chassis ground. Preserve this controlled connection and avoid long unprotected copper stubs near the connector.
Place the KSZ8794CNXCC close to the Ethernet magnetics and place all decoupling capacitors adjacent to their assigned supply and ground pins. Route RGMII, MII, or RMII signals over continuous reference planes with short point-to-point connections. Keep switching and clock sources away from copper-port traces, and verify the exposed-pad connection and via arrangement against the package drawing in the manufacturer datasheet.
Size the 3.3 V supply path for the worst combination of active ports, uplink mode, and temperature. Use local bulk and high-frequency decoupling as specified in the manufacturer application guidance, and provide low-impedance planes from the source to the switch. Since the device integrates biasing and termination, verify supply startup and current limits in the same operating modes used by the final network equipment.
Do not assume that a 64-pin QFN family member is automatically interchangeable. Before substituting KSZ8794CNXIC or KSZ8795CNXCC, compare the ordered pin table, exposed-pad requirements, temperature grade, host-interface timing, register definitions, and startup behavior. A footprint match alone does not guarantee software compatibility or identical management features, so qualify the complete Ethernet interface rather than only the physical package.
合規資訊
The Ethernet switch interface is not an automotive-qualified component classification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code and package form.