LAN9255-V/ZMX019 - 2/3-Port EtherCAT Controller | Microchip
MPN: LAN9255-V/ZMX019 ✓ 啟用中LAN9255-V/ZMX019 概覽
An EtherCAT device controller, or ESC, is a specialized communications semiconductor that manages distributed real-time fieldbus traffic and provides the electrical interface between an EtherCAT master and downstream slave devices. The LAN9255-V/ZMX019 combines that controller function with a general-purpose microcontroller, allowing EtherCAT communication and application-specific control logic to share one device while retaining access to the LAN9253 and SAM E53J signal sets.
The controller supports two or three EtherCAT ports, with two integrated full-duplex 100BASE-TX PHYs operating at 100 Mbps. A 512K programmable-memory configuration is indicated by the ZMX019 order code. The integrated SAM E53J core is based on the Arm Cortex-M4F architecture with hardware floating-point capability. The -V device is identified in the Microchip ordering guide as an extended-industrial temperature option, while ZMX identifies the 128-pin TQFP package.
The Ethernet side includes IEEE 802.3 controller functionality, RMII, USB 2.0, and serial flash interfaces identified in the product listings. Integrating the PHYs removes the need for separate Ethernet transceiver circuits in the standard EtherCAT port implementation. The microcontroller and EtherCAT signals are brought to package pins, allowing the hardware design to follow the pin-assignment and reference-layout guidance in the LAN9255 data sheet and hardware design checklist.
Typical uses include industrial servo drives, motion controllers, programmable automation controllers, I/O modules, robotics, and factory equipment that must exchange cyclic process data over EtherCAT. The same integration is useful in embedded machine-control systems where board space, deterministic communication, and local real-time processing are all important.
A critical design consideration is that the LAN9255 combines two functional blocks whose clocks, reset behavior, interfaces, and firmware must be coordinated. Follow the manufacturer's decoupling, PHY magnetics, crystal, and exposed-pad requirements exactly, and use the hardware design checklist as a PCB review reference before fabrication.
This page consolidates the verified family specifications, temperature and memory order-code differences, package constraints, and practical implementation considerations into one engineering reference. It also distinguishes true order-code alternatives from functional Ethernet devices that use different packages and cannot replace the part without a PCB redesign.
直接替換替代品,適用於 LAN9255-V/ZMX019 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LAN9255-V/ZMX019 (相同外形與佔位) — 差異在於 Operating Temperature, Package, Integrated MCU, Supply Voltage, EtherCAT Port Configuration.
LAN9255-I/ZMX019
✅ 直接替換聯絡詢價
查看資料表 →LAN9255/ZMX019
✅ 直接替換📋 參考替代品(不在目錄中)
LAN9255-V/ZMX020
✅ 直接替換聯絡詢價
查看資料表 →LAN9255-I/ZMX020
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LAN9255/ZMX020
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LAN9255-V/ZMX019 規格
| Device Type | 2/3-port EtherCAT device controller |
| Integrated MCU | SAM E53J with 32-bit Arm Cortex-M4F core |
| Integrated PHYs | 2 full-duplex 100BASE-TX transceivers |
| Ethernet Data Rate | 100 Mbps |
| EtherCAT Port Configuration | 2 or 3 ports |
| Programmable Memory | 512K |
| 供應電壓 | 3.3 V |
| 工作溫度 | -40°C to +105°C (Extended Industrial, -V) |
| 封裝 | 128-pin TQFP (ZMX), 14 x 14 mm |
| Ethernet Standard | IEEE 802.3 |
| USB Interface | USB 2.0 |
| MAC Interface | RMII |
| SPI Interface | SQI |
| Microchip Technology Product Page | LAN9255 |
| 安裝類型 | Surface mount |
LAN9255-V/ZMX019 128-pin tqfp (zmx), 14 x 14 mm 腳位配置指南
LAN9255-V/ZMX019(128-pin tqfp (zmx), 14 x 14 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: LAN9255-V/ZMX019.
請參閱 資料表 以查看完整腳位配置。
典型應用
LAN9255-V/ZMX019 適用於 6 應用s: Industrial EtherCAT Servo Drive, Distributed Motion and Robotics Controller, Programmable Automation I/O Module, Machine Vision Data Gateway, EtherCAT-Connected Power Electronics Controller, Embedded Test and Measurement Front End.
Industrial EtherCAT Servo Drive
The LAN9255-V/ZMX019 fits an EtherCAT servo-drive controller because it combines cyclic network communication with a 32-bit Arm Cortex-M4F processor in one 128-pin TQFP. The two integrated 100BASE-TX PHYs support the 100 Mbps EtherCAT interface while the MCU executes current-loop, position-loop, and fieldbus tasks locally. Its -40°C to +105°C extended-industrial range suits factory equipment with elevated ambient temperatures. Using one package reduces PCB area and avoids adding a separate Ethernet transceiver, although clocking, reset coordination, and exposed-pad thermal design must follow the Microchip hardware checklist.
推薦
Distributed Motion and Robotics Controller
The LAN9255-V/ZMX019 is useful in robotic arms, machine controllers, and distributed automation nodes that exchange real-time motion data over EtherCAT. Its Cortex-M4F core provides hardware floating-point support for control-loop calculations, while the integrated 100BASE-TX PHYs eliminate external PHY placement around the package. A 2/3-port architecture supports daisy-chained EtherCAT topologies without separate Ethernet silicon for each standard port. The design trade-off is firmware complexity: EtherCAT stack integration, the embedded MCU, memory mapping, and deterministic interrupt scheduling must be planned together from the start.
推薦
Programmable Automation I/O Module
The LAN9255-V/ZMX019 can serve as the communications and processing core of a programmable I/O module connected to an EtherCAT master. The integrated PHYs provide two full-duplex 100 Mbps links, and the 512K memory configuration gives the SAM E53J MCU room for an EtherCAT stack plus local channel logic. The extended-industrial temperature option supports factory cabinets where temperature variation is significant. Because the device combines communications and control functions, the module designer should partition memory and firmware carefully and validate watchdog behavior, boot sequencing, and diagnostic reporting.
推薦
Machine Vision Data Gateway
The LAN9255-V/ZMX019 can bridge machine-vision or inspection data into an EtherCAT network while performing local packet and control processing. Its two 100BASE-TX PHYs support EtherCAT connectivity, and the Cortex-M4F core is capable of handling protocol tasks and real-time control in the same device. The 128-pin TQFP package provides access to the LAN9253 EtherCAT signals and SAM E53J MCU signals, supporting custom external interfaces. Keep high-speed or noisy vision circuitry on separate power and ground domains, and follow the manufacturer's isolation and return-path guidance to prevent EtherCAT timing degradation.
推薦
EtherCAT-Connected Power Electronics Controller
The LAN9255-V/ZMX019 is appropriate for power-conversion equipment that accepts commands and returns diagnostics over EtherCAT while local MCU code executes supervisory functions. The 100 Mbps PHYs satisfy the Ethernet data rate, and the Cortex-M4F core provides efficient control processing without requiring a separate communications processor. Its extended-industrial range supports industrial power cabinets. The controller does not replace the power stage itself, so isolation, current sensing, gate-drive timing, and safety shutdown circuits remain separate hardware responsibilities; validate those paths independently of the EtherCAT firmware.
推薦
Embedded Test and Measurement Front End
The LAN9255-V/ZMX019 can act as the network-facing controller in a distributed test or measurement instrument, receiving cyclic commands from an EtherCAT master and executing local acquisition-control firmware on the Cortex-M4F core. The integrated PHYs reduce the number of external network components, while 512K memory accommodates an EtherCAT stack and control routines. The device is best suited to compact multi-axis measurement hardware rather than high-bandwidth bulk transfer, because the integrated Ethernet interface is 100 Mbps. Separate analog, precision-timing, and isolation circuitry should be partitioned carefully from the digital controller.
推薦
推薦產品摘要
工程參考資料,適用於 LAN9255-V/ZMX019 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LAN9255-I/ZMX019 | LAN9255/ZMX019 | LAN9255-V/ZMX020 | LAN9255-I/ZMX020 | LAN9255/ZMX020 |
|---|---|---|---|---|---|---|
| Package | 128-TQFP (ZMX, 14x14 mm) | 128-TQFP (ZMX, 14x14 mm) - same | 128-TQFP (ZMX, 14x14 mm) - same | 128-TQFP (ZMX, 14x14 mm) - same | 128-TQFP (ZMX, 14x14 mm) - same | 128-TQFP (ZMX, 14x14 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Temperature Designation | -V extended industrial | -I industrial | Standard commercial | -V extended industrial | -I industrial | Standard commercial |
| Programmable Memory | 512K | 512K - same | 512K - same | 1024K | 1024K | 1024K |
| Integrated MCU | SAM E53J with 32-bit Arm Cortex-M4F | SAM E53J with 32-bit Arm Cortex-M4F | SAM E53J with 32-bit Arm Cortex-M4F | SAM E53J with 32-bit Arm Cortex-M4F | SAM E53J with 32-bit Arm Cortex-M4F | SAM E53J with 32-bit Arm Cortex-M4F |
| Integrated PHY Count | 2 full-duplex 100BASE-TX PHYs | 2 full-duplex 100BASE-TX PHYs | 2 full-duplex 100BASE-TX PHYs | 2 full-duplex 100BASE-TX PHYs | 2 full-duplex 100BASE-TX PHYs | 2 full-duplex 100BASE-TX PHYs |
| Ethernet Data Rate | 100 Mbps | 100 Mbps | 100 Mbps | 100 Mbps | 100 Mbps | 100 Mbps |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
主要差異化特點
- Combines EtherCAT controller, dual PHYs, and Cortex-M4F processing (對比KSZ8041TLI-TR)
- Extended-industrial operating-temperature designation (對比LAN9255/ZMX019)
- Higher embedded memory option in the same footprint (對比LAN9255-V/ZMX019)
設計說明
Use the Microchip LAN9255 Hardware Design Checklist as the primary PCB review document before routing or fabrication. Pay particular attention to the 128-pin TQFP footprint, exposed-pad connection, power-plane geometry, and PHY trace routing. Maintain the datasheet-specified component placement and decoupling arrangement, and use continuous ground references beneath the high-speed Ethernet and MCU sections to minimize return-path discontinuities.
Route each Ethernet differential pair as a controlled-impedance pair with symmetrical geometry and continuous reference planes. Keep the PHY connections and magnetics-interface area isolated from switching power stages and noisy MCU signals. Avoid vias in the differential pair where possible, and observe the manufacturer spacing and isolation guidance between the EtherCAT interfaces and unrelated external circuits.
Decouple the 3.3 V supply close to every applicable power pin and follow the exact capacitor values and placement in the manufacturer reference design. The device contains both Ethernet and microcontroller circuitry, so supply transients can affect communications as well as computation. Validate startup sequencing, reset behavior, and the exposed-pad thermal path under maximum local processing and EtherCAT traffic.
Do not treat the Ethernet PHY data rate as the memory or firmware capacity, and do not substitute a generic Ethernet controller for this integrated part. Firmware must coordinate the EtherCAT stack with the SAM E53J Cortex-M4F application, including watchdog, reset, timing, and memory protection. Review order-code memory and temperature differences before release because the 019 and 020 suffixes are not interchangeable in firmware sizing.
合規資訊
Compliance statements are not printed in the manufacturer and distributor listings represented for this part. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations with Microchip Technology for the exact order code before environmental qualification.