LM2901PWR - Quad 30V Open-Collector Comparator | Texas Instruments
MPN: LM2901PWR ✓ 啟用中LM2901PWR 概覽
A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2901 belongs to the broader hierarchy of comparator integrated circuits, analog interface circuits, and semiconductor signal-conditioning devices. Unlike an operational amplifier used primarily for linear amplification, each comparator channel is intended for fast binary decision-making, level crossing, window detection, and open-drain interface signaling.
Four independent channels reduce package count in multi-channel threshold systems. According to the Texas Instruments datasheet, the LM2901 has a response time of 1 µs, an input offset voltage as low as 0.37 mV, and input bias current of 3.5 nA. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic and can sink current from multiple open-collector nodes when an external pull-up is installed.
The common-mode input range includes ground, which makes the device useful for detecting signals referenced to 0 V. The differential input range can equal the maximum-rated supply voltage of ±38 V for appropriate applications. A 14-pin TSSOP provides a compact surface-mount format, while the open-collector architecture requires an external pull-up resistor and leaves the output node in a high-impedance state whenever the output transistor is off.
Typical uses include industrial sensor thresholds, battery monitoring, overvoltage detection, motor-control interfaces, window comparators, and logic-level translation. Four channels can monitor multiple rails or compare several sensor outputs with the same comparator. The low 200 µA per-comparator supply current also makes the device suitable for mixed-signal systems where each active channel must consume limited power.
For reliable operation, select a pull-up resistor that keeps the output within the receiving logic family's voltage limits, route the exposed or sensitive inputs away from switching nodes, and account for input common-mode limits at every operating point. Because the outputs are open collector, a pull-up resistor is mandatory whenever a valid high output level is required.
This product page combines the manufacturer specifications, package and pinout information, qualified replacement choices, comparison parameters, and practical circuit guidance. It supports faster component identification while making the implementation trade-offs of the LM2901PWR's four-channel, open-collector architecture clear.
直接替換替代品,適用於 LM2901PWR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2901PWR (相同外形與佔位) — 差異在於 Package, Comparator Type, Supply Voltage Range, Input Offset Voltage, Supply Current.
LM2901PW
✅ 直接替換📋 參考替代品(不在目錄中)
LM2904PWR
✅ 直接替換聯絡詢價
查看資料表 →LM2902PWR
✅ 直接替換聯絡詢價
查看資料表 →LM2903PWR
✅ 直接替換聯絡詢價
查看資料表 →LM2901PWR
✅ 直接替換聯絡詢價
查看資料表 →NCV2901DTBR2G
✅ 直接替換📋 參考替代品(不在目錄中)
LM2901PWR 最大額定值與電氣特性
| Comparator Type | General-purpose differential comparator |
| Number of Channels | 4 channels |
| 供應電壓 | 2 V to 36 V |
| Dual Supply Voltage | ±1 V to ±18 V |
| Maximum Rated Supply | 38 V |
| 輸出類型 | Open-collector |
| Logic Compatibility | TTL, MOS, and CMOS |
| Low Input Offset Voltage | 0.37 mV |
| Low Input Bias Current | 3.5 nA |
| 供應電流 | 200 µA per comparator |
| Response Time | 1 µs |
| Common-Mode Input Range | Includes ground |
| Differential Input Voltage Range | ±38 V |
| ESD Rating | 2 kV HBM |
| 封裝 | 14-pin TSSOP |
| 安裝類型 | Surface mount |
LM2901PWR 14-pin tssop 腳位配置指南
LM2901PWR(14-pin tssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2901PWR.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2901PWR 適用於 6 應用s: Industrial Sensor Threshold Detection, Battery and Power Rail Monitoring, Overvoltage and Window Detection, Motor and Actuator Interfacing, Window Comparison for Analog Signals, Open-Drain Logic Level Translation.
Industrial Sensor Threshold Detection
The LM2901PWR fits industrial sensor interfaces that require several independent voltage thresholds on one compact package. Its four comparator channels can evaluate separate pressure, temperature, or position sensor outputs against adjustable references, while the 3.5 nA input bias current minimizes loading of high-impedance sensors. The common-mode range includes ground, allowing signals centered at 0 V to be detected directly. Each open-collector output can drive a digital input, alarm input, or relay-driver stage through an external pull-up. Because the device is not identified as AEC-Q100 qualified, automotive use requires a separate qualification review.
推薦
Battery and Power Rail Monitoring
The LM2901PWR is well suited to multi-rail battery supervision because four channels can independently compare different supply levels with reference thresholds. Its 38 V maximum rating provides headroom for monitored automotive or industrial battery systems, while the common-mode range including ground supports detection near 0 V. The 1 µs response time allows fast fault transitions to be captured, and the open-collector outputs can pull up a fault line or connect to a supervisor. Pull-up selection must ensure that no monitored rail or output exceeds the receiving device's absolute-maximum rating.
推薦
Overvoltage and Window Detection
The LM2901PWR can implement overvoltage, undervoltage, and window-monitoring functions by using two comparator channels for each monitored rail. With an input offset voltage of 0.37 mV, it can resolve small threshold differences when accurate reference and resistor networks are used. The open-collector architecture allows multiple channels to share a wired fault signal through suitable pull-up arrangements. Designers should account for input bias current, reference-node impedance, propagation delay, and output rise time because an open-collector output changes state rapidly but returns through the external pull-up.
推薦
Motor and Actuator Interfacing
The LM2901PWR can condition limit switches, position sensors, and analog control signals before they reach a motor or actuator controller. Its four channels permit compact comparison of multiple feedback signals, while the 1 µs response supports prompt detection of changing conditions. Open-collector outputs are useful when driving transistor gates, relay-driver inputs, or fault inputs because the receiving transistor can be supplied from a separate voltage domain. The common-mode input range including ground simplifies sensing around zero, although motor environments require careful grounding and protection from switching transients.
推薦
Window Comparison for Analog Signals
The LM2901PWR is appropriate for window comparison, where an input must remain between a lower and an upper threshold. Two channels can detect the lower and upper limits, and their open-collector outputs can be combined to produce a fault indication. The low 3.5 nA bias current is valuable when the source impedance is high, while 0.37 mV offset voltage helps preserve narrow threshold spacing. Practical implementations should use resistor ratios with suitable tolerances, account for comparator delay, and choose pull-up resistors that provide adequate rise time without excessive switching current.
推薦
Open-Drain Logic Level Translation
The LM2901PWR can support level translation when its open-collector output is pulled up to the destination logic voltage. The comparator determines whether the translated state is low or released, while the pull-up rail defines the high level independently of the comparator supply. This arrangement is useful between TTL, MOS, and CMOS receiving devices because the Texas Instruments datasheet identifies all three as compatible output loads. Confirm the pull-up voltage against every output's absolute-maximum rating, and avoid configurations where an external pull-up could back-power an input or output junction.
推薦
推薦產品摘要
工程參考資料,適用於 LM2901PWR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2901PW | LM2904PWR | LM2902PWR | LM2903PWR | LM2901PWR | NCV2901DTBR2G |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | ROHM Semiconductor | onsemi |
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Number of Pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
主要差異化特點
- Four channels in one 14-pin package (對比LM2901PW)
- Low input bias for threshold sensing (對比NCV2901DTBR2G)
- Open-collector flexibility with multiple logic families (對比LM2904PWR)
- Fast response for multi-rail detection (對比LM2902PWR)
設計說明
Place each comparator's reference and signal components close to the corresponding input pins, and keep the external pull-up resistor near the output receiver. Sensitive input traces should avoid switching-node and relay-coil routes. The LM2901's common-mode range includes ground, but the selected supply configuration still determines the usable common-mode interval, so check both input pins against those limits at startup, shutdown, and transient conditions.
Do not treat an open-collector output as actively driven high. When the output transistor turns off, the node rises only through the external pull-up. Use a resistor value that satisfies the receiver's high-level voltage and sink-current requirements while keeping the output rise time acceptable for the intended bus. Also avoid pull-up voltages that exceed the comparator output's absolute-maximum rating during power-off or brownout conditions.
Account for both comparator propagation delay and the RC rise time created by the pull-up resistor and input capacitance. The Texas Instruments datasheet specifies a 1 µs response time, but a wired fault signal may rise more slowly because the output is released rather than actively driven. For short pulse detection, use a local pull-up, minimize capacitive loading, and verify the complete system timing rather than relying on the transition time alone.
The four comparators draw approximately 200 µA each under the specified conditions, so budget for the complete device rather than one channel when designing a low-power system. The open-collector pull-ups can add system current whenever an output is released. Choose pull-up values that balance receiver noise margin, dynamic capacitance, and power consumption while remaining within the input and output voltage limits of the circuit.
合規資訊
The device is not identified as an AEC-Q100-qualified automotive comparator. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the applicable manufacturer declaration.