LM2901PWR - Quad 30V Open-Collector Comparator | Texas Instruments
Référence : LM2901PWR ✓ ActifLM2901PWR Présentation
A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2901 belongs to the broader hierarchy of comparator integrated circuits, analog interface circuits, and semiconductor signal-conditioning devices. Unlike an operational amplifier used primarily for linear amplification, each comparator channel is intended for fast binary decision-making, level crossing, window detection, and open-drain interface signaling.
Four independent channels reduce package count in multi-channel threshold systems. According to the Texas Instruments datasheet, the LM2901 has a response time of 1 µs, an input offset voltage as low as 0.37 mV, and input bias current of 3.5 nA. Its open-collector outputs are compatible with TTL, MOS, and CMOS logic and can sink current from multiple open-collector nodes when an external pull-up is installed.
The common-mode input range includes ground, which makes the device useful for detecting signals referenced to 0 V. The differential input range can equal the maximum-rated supply voltage of ±38 V for appropriate applications. A 14-pin TSSOP provides a compact surface-mount format, while the open-collector architecture requires an external pull-up resistor and leaves the output node in a high-impedance state whenever the output transistor is off.
Typical uses include industrial sensor thresholds, battery monitoring, overvoltage detection, motor-control interfaces, window comparators, and logic-level translation. Four channels can monitor multiple rails or compare several sensor outputs with the same comparator. The low 200 µA per-comparator supply current also makes the device suitable for mixed-signal systems where each active channel must consume limited power.
For reliable operation, select a pull-up resistor that keeps the output within the receiving logic family's voltage limits, route the exposed or sensitive inputs away from switching nodes, and account for input common-mode limits at every operating point. Because the outputs are open collector, a pull-up resistor is mandatory whenever a valid high output level is required.
This product page combines the manufacturer specifications, package and pinout information, qualified replacement choices, comparison parameters, and practical circuit guidance. It supports faster component identification while making the implementation trade-offs of the LM2901PWR's four-channel, open-collector architecture clear.
Alternatives de remplacement direct pour LM2901PWR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM2901PWR (même facteur de forme et même empreinte) — différant par Package, Comparator Type, Supply Voltage Range, Input Offset Voltage, Supply Current.
LM2901PW
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LM2904PWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2902PWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2903PWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2901PWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →NCV2901DTBR2G
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
LM2901PWR Valeurs maximales et caractéristiques électriques
| Comparator Type | General-purpose differential comparator |
| Number of Channels | 4 channels |
| Tension d'alimentation | 2 V to 36 V |
| Dual Supply Voltage | ±1 V to ±18 V |
| Maximum Rated Supply | 38 V |
| Type de sortie | Open-collector |
| Logic Compatibility | TTL, MOS, and CMOS |
| Low Input Offset Voltage | 0.37 mV |
| Low Input Bias Current | 3.5 nA |
| Courant d'alimentation | 200 µA per comparator |
| Response Time | 1 µs |
| Common-Mode Input Range | Includes ground |
| Differential Input Voltage Range | ±38 V |
| ESD Rating | 2 kV HBM |
| Boîtier | 14-pin TSSOP |
| Type de montage | Surface mount |
Guide de configuration des broches du LM2901PWR 14-pin tssop
Configuration des broches du LM2901PWR (boîtier 14-pin tssop). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.
Aucune donnée de brochage détaillée disponible pour LM2901PWR.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
LM2901PWR convient pour 6 applications: Industrial Sensor Threshold Detection, Battery and Power Rail Monitoring, Overvoltage and Window Detection, Motor and Actuator Interfacing, Window Comparison for Analog Signals, Open-Drain Logic Level Translation.
Industrial Sensor Threshold Detection
The LM2901PWR fits industrial sensor interfaces that require several independent voltage thresholds on one compact package. Its four comparator channels can evaluate separate pressure, temperature, or position sensor outputs against adjustable references, while the 3.5 nA input bias current minimizes loading of high-impedance sensors. The common-mode range includes ground, allowing signals centered at 0 V to be detected directly. Each open-collector output can drive a digital input, alarm input, or relay-driver stage through an external pull-up. Because the device is not identified as AEC-Q100 qualified, automotive use requires a separate qualification review.
Recommandé
Battery and Power Rail Monitoring
The LM2901PWR is well suited to multi-rail battery supervision because four channels can independently compare different supply levels with reference thresholds. Its 38 V maximum rating provides headroom for monitored automotive or industrial battery systems, while the common-mode range including ground supports detection near 0 V. The 1 µs response time allows fast fault transitions to be captured, and the open-collector outputs can pull up a fault line or connect to a supervisor. Pull-up selection must ensure that no monitored rail or output exceeds the receiving device's absolute-maximum rating.
Recommandé
Overvoltage and Window Detection
The LM2901PWR can implement overvoltage, undervoltage, and window-monitoring functions by using two comparator channels for each monitored rail. With an input offset voltage of 0.37 mV, it can resolve small threshold differences when accurate reference and resistor networks are used. The open-collector architecture allows multiple channels to share a wired fault signal through suitable pull-up arrangements. Designers should account for input bias current, reference-node impedance, propagation delay, and output rise time because an open-collector output changes state rapidly but returns through the external pull-up.
Recommandé
Motor and Actuator Interfacing
The LM2901PWR can condition limit switches, position sensors, and analog control signals before they reach a motor or actuator controller. Its four channels permit compact comparison of multiple feedback signals, while the 1 µs response supports prompt detection of changing conditions. Open-collector outputs are useful when driving transistor gates, relay-driver inputs, or fault inputs because the receiving transistor can be supplied from a separate voltage domain. The common-mode input range including ground simplifies sensing around zero, although motor environments require careful grounding and protection from switching transients.
Recommandé
Window Comparison for Analog Signals
The LM2901PWR is appropriate for window comparison, where an input must remain between a lower and an upper threshold. Two channels can detect the lower and upper limits, and their open-collector outputs can be combined to produce a fault indication. The low 3.5 nA bias current is valuable when the source impedance is high, while 0.37 mV offset voltage helps preserve narrow threshold spacing. Practical implementations should use resistor ratios with suitable tolerances, account for comparator delay, and choose pull-up resistors that provide adequate rise time without excessive switching current.
Recommandé
Open-Drain Logic Level Translation
The LM2901PWR can support level translation when its open-collector output is pulled up to the destination logic voltage. The comparator determines whether the translated state is low or released, while the pull-up rail defines the high level independently of the comparator supply. This arrangement is useful between TTL, MOS, and CMOS receiving devices because the Texas Instruments datasheet identifies all three as compatible output loads. Confirm the pull-up voltage against every output's absolute-maximum rating, and avoid configurations where an external pull-up could back-power an input or output junction.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM2901PWR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM2901PW | LM2904PWR | LM2902PWR | LM2903PWR | LM2901PWR | NCV2901DTBR2G |
|---|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | ROHM Semiconductor | onsemi |
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Number of Pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
Principaux différenciateurs
- Four channels in one 14-pin package (vs LM2901PW)
- Low input bias for threshold sensing (vs NCV2901DTBR2G)
- Open-collector flexibility with multiple logic families (vs LM2904PWR)
- Fast response for multi-rail detection (vs LM2902PWR)
Notes de conception
Place each comparator's reference and signal components close to the corresponding input pins, and keep the external pull-up resistor near the output receiver. Sensitive input traces should avoid switching-node and relay-coil routes. The LM2901's common-mode range includes ground, but the selected supply configuration still determines the usable common-mode interval, so check both input pins against those limits at startup, shutdown, and transient conditions.
Do not treat an open-collector output as actively driven high. When the output transistor turns off, the node rises only through the external pull-up. Use a resistor value that satisfies the receiver's high-level voltage and sink-current requirements while keeping the output rise time acceptable for the intended bus. Also avoid pull-up voltages that exceed the comparator output's absolute-maximum rating during power-off or brownout conditions.
Account for both comparator propagation delay and the RC rise time created by the pull-up resistor and input capacitance. The Texas Instruments datasheet specifies a 1 µs response time, but a wired fault signal may rise more slowly because the output is released rather than actively driven. For short pulse detection, use a local pull-up, minimize capacitive loading, and verify the complete system timing rather than relying on the transition time alone.
The four comparators draw approximately 200 µA each under the specified conditions, so budget for the complete device rather than one channel when designing a low-power system. The open-collector pull-ups can add system current whenever an output is released. Choose pull-up values that balance receiver noise margin, dynamic capacitance, and power consumption while remaining within the input and output voltage limits of the circuit.
Informations de conformité
The device is not identified as an AEC-Q100-qualified automotive comparator. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the applicable manufacturer declaration.