LM2902KDBRE4 - Quad 26V 1.2MHz Op Amp | Texas Instruments
MPN: LM2902KDBRE4 ✓ 啟用中LM2902KDBRE4 概覽
An operational amplifier, commonly called an op amp, is a high-gain differential-input amplifier whose external feedback network determines its closed-loop behavior. Within the broader semiconductor hierarchy, an op amp is a linear integrated circuit used for voltage amplification, current-to-voltage conversion, filtering, comparison, and buffering. The LM2902 combines four such amplifier channels in one package, reducing board area compared with four separately packaged devices.
The principal characteristics include operation from dual supplies of up to ±13 V, a 26 V total supply rating, a 1.2 MHz gain-bandwidth product, and input offset voltage specified at 2 mV for the LM2902 product family. A typical input offset voltage of 3 mV and typical input offset current of 2 nA are also identified. The common-mode input range includes ground, allowing direct sensing near the lower supply rail, while the low input bias and offset parameters support precision low-frequency signal conditioning.
Each channel uses internal frequency compensation, removing the need for an external compensation capacitor in ordinary closed-loop configurations. The design includes ESD protection characterized as less than 500 V using the MIL-STD-883 Method 3015 procedure and greater than 200 V using the machine model. The manufacturer also identifies the LM2902 as qualified for automotive applications under AEC-Q100, with customer-specific configuration control and major-change approval support.
Typical uses include sensor-signal conditioning, transducer amplification, analog control loops, audio preamplification, bridge-balancing networks, and low-frequency active filters. Four integrated channels can reduce component count in designs requiring several matched general-purpose amplifier functions. Common-mode input voltage that includes ground makes the device useful in circuits powered from positive-only supplies where the signal approaches zero volts.
Design with adequate supply bypass capacitance and route input and output traces to minimize parasitic coupling. Confirm common-mode, output-swing, and input-bias requirements against the load and supply conditions. Because a linear amplifier dissipates power proportional to supply voltage and output current, thermal analysis remains important when driving low-impedance loads or operating at elevated ambient temperature.
This product page combines manufacturer specifications, package and ordering information, verified source links, application guidance, and practical replacement considerations. It supports faster component evaluation while directing engineers to the manufacturer datasheet for final pin assignments, limiting values, test conditions, and qualification details.
直接替換替代品,適用於 LM2902KDBRE4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2902KDBRE4 (相同外形與佔位) — 差異在於 Amplifier Type, Package.
此產品無可直接替換的替代品。
申請替代品LM2902KDBRE4 最大額定值與電氣特性
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Amplifier Channels | 4 circuits |
| Maximum Total Supply Voltage | 26 V |
| Maximum Dual Supply Voltage | ±13 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Maximum Input Offset Voltage | 2 mV |
| Typical Input Offset Voltage | 3 mV |
| Typical Input Offset Current | 2 nA |
| Typical Supply Current | 0.8 mA |
| Common-Mode Input Voltage | Includes ground |
| Frequency Compensation | Internal |
| 封裝 | 14-pin SSOP |
| Packaging | Tape and reel |
| ESD Protection, MIL-STD-883 Method 3015 | <500 V |
| Machine-Model ESD Protection | >200 V at 200 pF |
| Automotive Qualification | AEC-Q100 qualified |
| Configuration Control | Customer-specific support with major-change approval |
LM2902KDBRE4 14-pin ssop 腳位配置指南
LM2902KDBRE4(14-pin ssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2902KDBRE4.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2902KDBRE4 適用於 6 應用s: Sensor Signal Conditioning, Industrial Control Loops, Audio Preamplification, Active Filtering, Data Acquisition Front End, Automotive Low-Speed Control.
Sensor Signal Conditioning
The LM2902KDBRE4 fits low-frequency sensor-conditioning circuits requiring four amplifier channels in one 14-pin SSOP package. Its common-mode input range includes ground, making it useful when the sensor output approaches zero volts, while the typical 2 nA input offset current helps reduce bias-related errors with high-impedance sources. Four internally compensated channels can support buffering, gain stages, active filtering, and output conditioning without requiring four separate packages. The designer should verify sensor output range and bandwidth against the device’s 1.2 MHz gain-bandwidth product, then confirm that the 26 V maximum total supply accommodates every transient and supply configuration.
推薦
Industrial Control Loops
The LM2902KDBRE4 is appropriate for general industrial feedback and control loops that operate below its 1.2 MHz bandwidth limit. Four channels can implement error amplification, actuator conditioning, current sensing, and feedback paths within a compact board area. The maximum total supply rating of 26 V accommodates common industrial signal-chain voltages, and internal frequency compensation simplifies ordinary closed-loop implementation. Designers should still check output current, output swing, settling behavior, and common-mode range against the controller and load. Robust grounding, supply bypassing, and isolation from switching nodes are necessary to prevent induced noise from appearing directly in the control signal.
推薦
Audio Preamplification
The LM2902KDBRE4 can serve as a general-purpose preamplifier in low-frequency audio and instrumentation paths that do not require rail-to-rail operation. Its four amplifier channels allow two channels to process stereo signals while the remaining channels support gain, summing, or buffering functions. Internal frequency compensation removes the need for external compensation capacitors in conventional closed-loop stages, and the 26 V total supply limit permits operation from ±13 V supplies. Audio performance depends on output swing into the selected load, noise behavior at the signal bandwidth, and layout cleanliness. The circuit should use short, shielded input routes and a stable return path to minimize hum and interference.
推薦
Active Filtering
The LM2902KDBRE4 is suitable for first-order and modest higher-order active filters built around general-purpose closed-loop amplifier stages. Four channels provide flexibility for cascaded low-pass, high-pass, notch, or buffering sections, while internal frequency compensation supports stable operation at practical gains. Its 1.2 MHz gain-bandwidth product limits the usable signal range and should be compared with the filter’s corner frequency and required closed-loop gain. Precision passive components and stable references become increasingly important as the filter response tightens. Confirm the actual input and output signal levels so neither amplifier saturates, and test the completed board for oscillation and sensitivity to load capacitance.
推薦
Data Acquisition Front End
The LM2902KDBRE4 can condition low-frequency inputs in a data-acquisition front end when the required bandwidth and precision fall within the LM2902 performance class. Four channels allow independent amplification and buffering for multiple sensors or a multiplexed measurement chain. The common-mode input range including ground supports circuits that measure signals near the lower rail, while the 2 mV maximum input offset specification is important for small-signal measurements. For higher-resolution systems, verify input offset drift, input bias behavior, noise density, and common-mode rejection at the actual operating frequency. Add input protection and reference grounding carefully so protection leakage does not dominate the sensor signal.
推薦
Automotive Low-Speed Control
The LM2902KDBRE4 supports low-speed signal-processing functions in automotive electronics because its documentation identifies the LM2902 family as AEC-Q100 qualified. Four internally compensated amplifier channels can handle sensor interfaces, actuator drivers, and feedback networks within a 26 V maximum total supply environment. Automotive qualification does not remove the need for application-level validation, so engineers should review transient immunity, temperature limits, EMC performance, and the exact ordering-code configuration. Production procurement should apply customer-specific configuration-control and major-change-approval procedures where supported. Keep sensitive input routes away from high-current loads and vehicle power domains to minimize coupled noise.
推薦
推薦產品摘要
工程參考資料,適用於 LM2902KDBRE4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Brand | Texas Instruments |
| Package | 14-pin SSOP |
| Amplifier Configuration | Quad general-purpose operational amplifier |
| Maximum Total Supply Voltage | 26 V |
| Maximum Dual Supply Voltage | ±13 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Maximum Input Offset Voltage | 2 mV |
| Frequency Compensation | Internal |
| Automotive Qualification | AEC-Q100 qualified |
| Delivery Packaging | Tape and reel |
主要差異化特點
- Four integrated general-purpose amplifier channels (對比LM2902KDBRG4)
- General-purpose 26 V supply capability (對比LM2902KDR)
- Automotive-oriented family qualification (對比LM2902KDBRG4)
設計說明
Place the supply bypass capacitor close to the device’s power and ground pins, and keep the return path short to reduce supply impedance. The LM2902 is intended for operation up to a 26 V total supply, but correct decoupling and grounding remain necessary at every operating point. Check the selected capacitor’s DC-bias derating and temperature rating so effective capacitance remains adequate at the actual supply voltage.
Route each amplifier channel’s input and output as short and direct as practical, with a continuous return plane beneath the device. Four channels can create crosstalk if sensitive inputs run parallel to outputs or switching-node wiring. Respect the 14-pin SSOP land pattern from the manufacturer package drawing, confirm pin orientation during inspection, and avoid placing test pads or long stubs adjacent to high-impedance input nodes.
Do not interpret the 26 V rating as permission to exceed input or output limits. Verify common-mode range, output swing, load current, and stable operating gain against the actual supply. Because the common-mode input range includes ground but does not imply rail-to-rail capability, check the datasheet waveform limits before using the amplifier at the positive rail or driving loads near the output limits.
Estimated: power dissipation depends on the actual supply, output voltage, load current, and ambient temperature because the output stage can dissipate current even when the output remains below the rail. Use the manufacturer’s electrical limits and thermal information to determine the worst-case condition. Provide adequate copper area around the SSOP and avoid enclosing the device in a thermally isolated enclosure without thermal analysis.
合規資訊
The LM2902 documentation identifies AEC-Q100 qualification for automotive applications and states that customer-specific configuration control can be supported along with major-change approval. ESD ratings are identified as less than 500 V using MIL-STD-883 Method 3015 and greater than 200 V using the machine model at 200 pF.