Texas Instruments

LM358ADGKR - Dual 30V 700kHz Op Amp | Texas Instruments

MPN: LM358ADGKR ✓ 啟用中
30 V Vdss VSSOP (DGK) Package Frequency compensated Speed
MOQ: 1 |

LM358ADGKR 概覽

The Texas Instruments LM358ADGKR is a dual general-purpose operational amplifier with two independent amplifier channels, a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and 3 mV input offset voltage. The device is supplied in an 8-pin VSSOP DGK package for compact surface-mount designs. Its dual architecture allows both channels to operate from a common supply while supporting single-supply or split-supply operation.

An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify voltage differences. The LM358 belongs to the operational-amplifier hierarchy within amplifier ICs, analog ICs, and semiconductor devices. Its two channels are internally frequency compensated, allowing straightforward use in common amplifier configurations without external compensation networks.

The LM358A family's principal characteristics include two amplifiers per package, operation from a supply rated up to 30 V, a 700 kHz gain-bandwidth product, and a 3 mV offset-voltage specification. These ratings make the device suitable for general-purpose signal conditioning where moderate bandwidth, wide supply-voltage headroom, and low component count are more important than very high precision or very high speed.

Each channel includes differential inputs and an output. With negative feedback applied, the closed-loop gain is set by the external resistor network rather than by the amplifier's very high open-loop gain. The manufacturer describes the LM358A as an industry-standard dual operational amplifier. Designers should therefore account for input common-mode range, output swing, supply voltage, input bias current, noise, offset, and stability requirements when choosing feedback and biasing components.

Typical uses include low-frequency audio amplification, sensor-signal conditioning, DC error amplification in control systems, buffer stages, and general instrumentation. The dual channel count is useful when a board needs two independent amplifier functions, such as a transimpedance stage followed by an output-conditioning amplifier. The 8-pin VSSOP package also reduces board area compared with larger dual operational-amplifier packages.

The primary design consideration is to verify signal amplitudes against the operating conditions for the selected supply voltage. Input and output voltages must remain within the limits stated in the manufacturer datasheet, and unused channels should be configured according to the recommended application circuit rather than left with floating inputs. Decoupling capacitors should be placed close to the supply pins to limit impedance in the supply-return path.

This product page combines the official LM358A specifications with package, pinout, procurement, comparison, and design guidance. It also identifies pin-compatible options and explains the electrical checks required before changing an operational amplifier in an existing analog circuit.

直接替換替代品,適用於 LM358ADGKR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: LM358ADGKR (相同外形與佔位) — 差異在於 Input Offset Voltage, Maximum Supply Voltage, Amplifier Type, Gain-Bandwidth Product, Differential Input Voltage Capability.

Texas Instruments
Input Offset Voltage: 2 mV
Maximum Supply Voltage: 16 V
Amplifier Type: General purpose
比較對象 LM358ADGKR →
Texas Instruments
Maximum Supply Voltage: 36 V
Amplifier Type: General-purpose operational amplifier
Gain-Bandwidth Product: 1.2 MHz
比較對象 LM358ADGKR →
Texas Instruments
Input Offset Voltage: 300 µV typical
Maximum Supply Voltage: 36 V
Differential Input Voltage Capability: High; exact limit not stated
比較對象 LM358ADGKR →

LM358DGKR

✅ 直接替換
Texas Instruments
📦 VSSOP-8 (DGK)
2 channels · 36 V · 300 µV typical · Extends to ground · High; exact limit not stated · 8-pin VSSOP · Standard general-purpose dual operational amplifier · Surface mount

聯絡詢價

查看資料表 →

LM358ADGKRG4

✅ 直接替換
Texas Instruments
📦 VSSOP-8 (DGK)
2 circuits · General purpose · 700 kHz · 0.7 MHz · 0.3 V/µs · 2 mV · 200 nA · 0.7 mA

聯絡詢價

查看資料表 →

LM358ADGKR 最大額定值與電氣特性

Amplifier Type Dual general-purpose operational amplifier
Number of Amplifier Channels 2 channels
Maximum Supply Voltage 30 V
Gain-Bandwidth Product 700 kHz
Input Offset Voltage 3 mV
工作溫度範圍 0 °C to +70 °C
Package Type VSSOP (DGK)
腳位數 8 pins
安裝類型 Surface mount
Supply Configuration Single or split supply
Internal Frequency Compensation Frequency compensated

LM358ADGKR 腳位配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
腳位 1 OUT1 — Output of amplifier channel 1
腳位 2 IN1- — Inverting input of amplifier channel 1
腳位 3 IN1+ — Noninverting input of amplifier channel 1
腳位 4 V- — Negative supply connection
腳位 5 IN2+ — Noninverting input of amplifier channel 2
腳位 6 IN2- — Inverting input of amplifier channel 2
腳位 7 OUT2 — Output of amplifier channel 2
腳位 8 V+ — Positive supply connection

典型應用

LM358ADGKR 適用於 6 應用s: Sensor Signal Conditioning, Industrial Control Error Amplifier, Audio Preamplifier, Measurement Instrumentation Buffer, Power Supply Feedback Control, Interface and Filter Stage.

🧩

Sensor Signal Conditioning

LM358ADGKR is suitable for conditioning relatively slow sensor outputs that require amplification and level translation within a 30 V maximum supply environment. Place one channel in the signal path and use the second channel for gain, offset, filtering, or buffer functions. Its 700 kHz gain-bandwidth product provides useful bandwidth for low-frequency sensors, while the 3 mV specified offset must be considered when the measured signal is small. The circuit should remain within the datasheet's input common-mode and output-swing limits, which vary with supply voltage. Suitable sensors include resistive bridges, temperature elements, and slow analog transducers whose bandwidth is well below the amplifier's capability.

🏭

Industrial Control Error Amplifier

The two channels of LM358ADGKR can implement error amplification and an actuator-feedback stage in a basic industrial control system. A 30 V maximum supply rating provides useful voltage headroom for circuits referenced to higher-voltage control rails, and the 700 kHz bandwidth allows the loop to respond to many process-control dynamics rather than only static errors. The 3 mV offset specification should be included in the accuracy budget for low-level feedback signals. Compensation and stability components must be selected from the manufacturer application information for the selected closed-loop gain and load. Industrial temperature and isolation requirements should also be checked if the controller operates outside the device's 0 °C to +70 °C rating.

🎧

Audio Preamplifier

LM358ADGKR can serve as a low-frequency audio preamplifier when its noise, offset, slew-rate, and output-drive requirements meet the source impedance and signal level. The 700 kHz gain-bandwidth product covers audio-band applications with moderate closed-loop gain, while two amplifiers allow independent gain and buffering stages in one package. Because the device is a general-purpose operational amplifier rather than a dedicated low-noise audio component, the complete input-noise and distortion behavior must be reviewed for high-fidelity paths. The 30 V maximum supply rating does not require a 30 V operating rail; selecting a lower supply can improve headroom and simplify output-swing design.

⚡

Measurement Instrumentation Buffer

LM358ADGKR is useful for buffering a measurement source before a downstream converter or display input. One channel can provide impedance buffering, while the other can implement gain or active filtering, helping isolate the source from measurement-system loading. Its 700 kHz bandwidth is appropriate for many low-speed laboratory and industrial measurements, but offset error remains 3 mV as specified. Designers should calculate the closed-loop gain from the feedback resistors, check source impedance against the input-bias-current requirement, and maintain input and output voltages within the operating limits. The VSSOP-8 package supports compact analog boards while reducing the number of separate amplifier packages required.

⚡

Power Supply Feedback Control

LM358ADGKR can amplify the error voltage between a power-supply feedback node and a reference, providing a compact control path for an external regulator topology. The dual channels can handle error amplification and output buffering, while the 30 V maximum supply rating supports control circuits connected to higher-voltage rails. The 700 kHz gain-bandwidth product is suitable for many moderate-bandwidth control loops, but compensation must be derived from the plant and must preserve phase margin. The 3 mV input offset contributes directly to the regulation error. This application requires careful common-mode-range, output-swing, and stability analysis rather than treating the amplifier as a fixed-voltage regulator.

🔧

Interface and Filter Stage

LM358ADGKR can implement active filters and interface stages between sensors, logic families, or external transducers. Two channels permit a filter and a buffer to share one package, reducing board area in compact control systems. Its 700 kHz gain-bandwidth product supports filter frequencies well below the closed-loop bandwidth when appropriate resistor and capacitor values are selected. Component tolerances determine much of the actual filter accuracy, while the 3 mV offset can influence the DC operating point of a low-frequency active filter. Verify noise, input-bias current, common-mode range, and output drive against the source and load before finalizing the circuit.

What is the operating voltage of LM358ADGKR?
The LM358ADGKR is rated for operation with a maximum supply voltage of 30 V. According to the Texas Instruments LM358A product page, the device is a dual operational amplifier intended for single-supply or split-supply operation. The 30 V figure is the maximum supply rating, not the output-voltage range, and individual input and output limits remain subject to the manufacturer datasheet.
What are the key specifications of LM358ADGKR that engineers should know?
The LM358ADGKR combines two operational-amplifier channels, a 30 V maximum supply rating, a 700 kHz gain-bandwidth product, and a 3 mV input offset voltage in an 8-pin VSSOP package. According to the Texas Instruments LM358A product page, it is a general-purpose, industry-standard dual operational amplifier designed for single or split supplies.
What is the gain-bandwidth product of LM358ADGKR?
The LM358ADGKR has a gain-bandwidth product of 700 kHz. According to the Texas Instruments LM358A product page, this bandwidth supports general-purpose amplification of low- and moderate-frequency signals. Practical closed-loop bandwidth also depends on the selected gain, feedback network, load, and the amplifier's stability characteristics.
What is the input offset voltage of LM358ADGKR?
The specified input offset voltage for LM358ADGKR is 3 mV. According to the Texas Instruments LM358A product page, this parameter represents the small differential voltage needed to bring the output into its linear operating region. For precision DC measurements, the complete offset-voltage and drift limits should be checked for the selected temperature range.
Where can I download the LM358ADGKR datasheet PDF?
The official LM358A product page provides the Texas Instruments LM358A datasheet and ordering information for LM358ADGKR. Use the linked data-sheet document on that manufacturer page for the authoritative package drawing, pin descriptions, electrical characteristics, recommended circuits, and operating limits. The LM358ADGKR ordering entry identifies the part as an 8-pin VSSOP DGK device.
Where can I find the LM358ADGKR pinout?
The LM358ADGKR pinout is defined by the 8-pin VSSOP DGK drawing in the Texas Instruments LM358A manufacturer datasheet. The package contains two operational-amplifier channels, with the two noninverting inputs, two inverting inputs, two outputs, supply connections, and ground connection distributed across the eight numbered pins. Use the package drawing when assigning PCB tracks.
Can LM358ADGKR operate from a single 5 V supply?
The LM358ADGKR is designed to operate from single or split supplies, so a 5 V implementation falls within its intended supply architecture. However, the usable input common-mode and output-swing ranges depend on the actual supply voltage. According to the Texas Instruments LM358A documentation, consult the electrical-characteristics plots before operating signals near the supply rails.
What is the best drop-in replacement for LM358ADGKR?
LM358ADGKR and LM358DGKR are the closest same-package choices identified for replacement review, both using the 8-pin DGK VSSOP format. The manufacturer and cross-reference information establish the shared package family, but exact offset, temperature, and grade requirements must still be compared before substitution. LM358ADGKRG4 is another same-footprint ordering option with the same nominal device designation.
What can replace LM358ADGKR?
LM358DGKR and LM358ADGKRG4 are same-brand, 8-pin DGK VSSOP alternatives associated with the LM358ADGKR family. Both retain the dual-op-amp architecture, 30 V nominal supply class, and 700 kHz bandwidth class, making them the most direct candidates for footprint review. Confirm pin functions, electrical limits, temperature range, and qualification requirements in the manufacturer documentation before production use.
Is LM358ADGKR the same as LM358DGKR?
LM358ADGKR and LM358DGKR share the 8-pin DGK VSSOP package and the same general LM358 dual-amplifier device family. The available comparison material identifies package and compliance attributes for comparison but does not establish that every electrical limit is identical. A drop-in decision should therefore include a channel-by-channel comparison of offset, bandwidth, bias current, noise, common-mode range, and temperature limits.
When should I choose LM358ADGKR instead of another dual op amp?
Choose LM358ADGKR when the design needs two general-purpose amplifier channels, a 30 V maximum supply rating, and a 700 kHz gain-bandwidth product in a compact VSSOP package. It is a practical choice for conventional instrumentation and signal-conditioning blocks where internal frequency compensation, single- or split-supply use, and simple closed-loop configuration are priorities.
Is LM358ADGKR suitable for sensor signal conditioning?
Yes, LM358ADGKR is suitable for many sensor-signal-conditioning circuits because it provides two channels, a 30 V maximum supply rating, and 700 kHz gain-bandwidth product. According to the Texas Instruments LM358A product page, it is an industry-standard dual operational amplifier. The sensor output range, required gain, noise, offset, and common-mode limits must be checked against the complete electrical characteristics.
How does LM358ADGKR compare with a precision op amp?
LM358ADGKR favors general-purpose flexibility rather than precision amplification: its specified input offset voltage is 3 mV, while its 700 kHz gain-bandwidth product supports moderate-frequency signal processing. A precision amplifier may offer lower offset and drift, but may impose different supply, noise, or bandwidth limits. The correct choice depends on the signal amplitude and accuracy required by the application.
Where can I buy LM358ADGKR and request a quotation?
Use the Request a Quote form on this page to request LM358ADGKR pricing, stock confirmation, and lead-time information. The quote form is the appropriate channel for a current commercial offer because inventory and pricing can change. Confirm the exact LM358ADGKR ordering code, 8-pin DGK package, quantity, and target delivery date when submitting the request.
What is the lead time for LM358ADGKR?
Current LM358ADGKR lead time should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, package availability, and current manufacturing conditions. Provide the required quantity, target delivery date, and approved manufacturer or manufacturer-approved sourcing status when requesting the quotation.
Is LM358ADGKR currently in stock?
Current LM358ADGKR stock status should be confirmed through the Request a Quote form on this page rather than assumed from a historical catalog entry. Inventory changes with market demand and order volume, so a written quotation should confirm availability for the requested quantity. Include the exact 8-pin DGK package and target shipment location in the request.

工程參考資料,適用於 LM358ADGKR — 比較、設計指引及合規資訊。

選型指南

Choose LM358ADGKR for compact, general-purpose dual-amplifier designs that need a 30 V maximum supply rating, 700 kHz gain-bandwidth product, and operation from single or split supplies. Its two channels can reduce package count in signal-conditioning, feedback-control, filtering, and low-frequency audio circuits. LM358DGKR is a practical same-footprint candidate to review when the exact LM358A ordering requirement is not essential, but production use should follow a complete electrical and qualification comparison. LM358ADGKRG4 is the closest same-brand ordering alternative and is especially relevant when the G4 orderable designation or its associated manufacturing status is specified. For applications requiring offset drift, noise, bandwidth, common-mode range, or temperature performance beyond the LM358A family ratings, select a more specialized operational amplifier instead of forcing a footprint-compatible general-purpose part.

與替代品比較

參數 本產品 LM358DGKR LM358ADGKRG4
Package VSSOP-8 (DGK) VSSOP-8 (DGK) - same package VSSOP-8 (DGK) - same package
Brand Texas Instruments Texas Instruments Texas Instruments
Amplifier Channels 2 channels 2 channels 2 channels
Maximum Supply Voltage 30 V 30 V nominal device family 30 V nominal device family
Gain-Bandwidth Product 700 kHz 700 kHz nominal device family 700 kHz nominal device family
Supply Configuration Single or split supply Single or split supply Single or split supply
Mounting Type Surface mount Surface mount Surface mount

主要差異化特點

  • Two independent amplifier channels in one compact package (對比LM358ADGKRG4)
  • Wide maximum supply rating for general-purpose analog systems (對比LM358DGKR)
  • Single-package consolidation for two-stage signal chains (對比LM358ADGKRG4)

設計說明

Decouple each supply connection with a local ceramic capacitor and connect the ground reference directly to the package ground pin. Keep the input, output, feedback, and ground paths compact because long traces can add parasitic resistance, inductance, and coupling. The manufacturer datasheet should be used for the recommended capacitor values, acceptable ceramic types, and the device's input and output current limits.

Do not assume that the 30 V maximum supply rating permits the input and output to swing across the full supply range. Check the input common-mode range and output-swing limits for the actual supply voltage, especially in low-voltage single-supply systems. Also avoid allowing either input to float; configure unused channels according to the manufacturer recommendation so they remain in a defined operating state.

Calculate closed-loop bandwidth from the 700 kHz gain-bandwidth product rather than treating that value as usable bandwidth at every gain. Higher closed-loop gain narrows the available bandwidth and can require noise-gain compensation. When driving capacitive loads, add isolation resistance or place the amplifier behind a suitable buffer, and verify stability experimentally rather than relying only on nominal bandwidth.

Use a compact analog layout with the bypass capacitor adjacent to the supply pin and a low-impedance ground plane or ground pour beneath the device. Route feedback components close to the relevant channel pins and keep sensitive input traces away from switching nodes and high-current paths. Because the package is VSSOP-8, verify land pattern dimensions and pin numbering against the manufacturer package drawing before fabrication.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The manufacturer product page identifies LM358ADGKR, but no explicit target-part RoHS, REACH, halogen-free, lead-free, or conflict-minerals declaration is shown. The device is a general-purpose commercial amplifier rather than an AEC-Q100 automotive-qualified variant.

相關搜尋

LM358ADGKR datasheet LM358ADGKR pinout LM358ADGKR datasheet pdf LM358ADGKR specifications LM358ADGKR equivalent LM358ADGKR replacement LM358ADGKR vs LM358DGKR LM358ADGKR price LM358ADGKR stock Texas Instruments LM358ADGKR LM358ADGKR VSSOP-8 footprint LM358ADGKR application circuit

相關元件與詞彙

Texas Instruments LM358ADGKR LM358DGKR LM358ADGKRG4 LM358A operational amplifier dual operational amplifier general-purpose amplifier amplifier IC analog IC semiconductor single-supply operation split-supply operation gain-bandwidth product input offset voltage negative feedback internal frequency compensation VSSOP-8 DGK package surface-mount package signal conditioning error amplifier active filter audio preamplifier power-supply feedback control
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情