LM358ADGKR - Dual 30V 700kHz Op Amp | Texas Instruments
부품 번호: LM358ADGKR ✓ 활성LM358ADGKR 개요
An operational amplifier is an analog integrated circuit that uses high open-loop gain and negative feedback to amplify voltage differences. The LM358 belongs to the operational-amplifier hierarchy within amplifier ICs, analog ICs, and semiconductor devices. Its two channels are internally frequency compensated, allowing straightforward use in common amplifier configurations without external compensation networks.
The LM358A family's principal characteristics include two amplifiers per package, operation from a supply rated up to 30 V, a 700 kHz gain-bandwidth product, and a 3 mV offset-voltage specification. These ratings make the device suitable for general-purpose signal conditioning where moderate bandwidth, wide supply-voltage headroom, and low component count are more important than very high precision or very high speed.
Each channel includes differential inputs and an output. With negative feedback applied, the closed-loop gain is set by the external resistor network rather than by the amplifier's very high open-loop gain. The manufacturer describes the LM358A as an industry-standard dual operational amplifier. Designers should therefore account for input common-mode range, output swing, supply voltage, input bias current, noise, offset, and stability requirements when choosing feedback and biasing components.
Typical uses include low-frequency audio amplification, sensor-signal conditioning, DC error amplification in control systems, buffer stages, and general instrumentation. The dual channel count is useful when a board needs two independent amplifier functions, such as a transimpedance stage followed by an output-conditioning amplifier. The 8-pin VSSOP package also reduces board area compared with larger dual operational-amplifier packages.
The primary design consideration is to verify signal amplitudes against the operating conditions for the selected supply voltage. Input and output voltages must remain within the limits stated in the manufacturer datasheet, and unused channels should be configured according to the recommended application circuit rather than left with floating inputs. Decoupling capacitors should be placed close to the supply pins to limit impedance in the supply-return path.
This product page combines the official LM358A specifications with package, pinout, procurement, comparison, and design guidance. It also identifies pin-compatible options and explains the electrical checks required before changing an operational amplifier in an existing analog circuit.
드롭인 대체품: LM358ADGKR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM358ADGKR (동일 폼 팩터 및 풋프린트) — 차이점: Input Offset Voltage, Maximum Supply Voltage, Amplifier Type, Gain-Bandwidth Product, Differential Input Voltage Capability.
LM358DGKR
✅ 드롭인가격 문의
데이터시트 보기 →LM358ADGKRG4
✅ 드롭인가격 문의
데이터시트 보기 →LM358ADGKR 최대 정격 & 전기적 특성
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifier Channels | 2 channels |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 700 kHz |
| Input Offset Voltage | 3 mV |
| 동작 온도 범위 | 0 °C to +70 °C |
| Package Type | VSSOP (DGK) |
| 핀 수 | 8 pins |
| 실장 유형 | Surface mount |
| Supply Configuration | Single or split supply |
| Internal Frequency Compensation | Frequency compensated |
LM358ADGKR 핀 구성
| 핀 1 | OUT1 — Output of amplifier channel 1 |
| 핀 2 | IN1- — Inverting input of amplifier channel 1 |
| 핀 3 | IN1+ — Noninverting input of amplifier channel 1 |
| 핀 4 | V- — Negative supply connection |
| 핀 5 | IN2+ — Noninverting input of amplifier channel 2 |
| 핀 6 | IN2- — Inverting input of amplifier channel 2 |
| 핀 7 | OUT2 — Output of amplifier channel 2 |
| 핀 8 | V+ — Positive supply connection |
일반적인 애플리케이션
LM358ADGKR 적합 용도: 6 애플리케이션s: Sensor Signal Conditioning, Industrial Control Error Amplifier, Audio Preamplifier, Measurement Instrumentation Buffer, Power Supply Feedback Control, Interface and Filter Stage.
Sensor Signal Conditioning
LM358ADGKR is suitable for conditioning relatively slow sensor outputs that require amplification and level translation within a 30 V maximum supply environment. Place one channel in the signal path and use the second channel for gain, offset, filtering, or buffer functions. Its 700 kHz gain-bandwidth product provides useful bandwidth for low-frequency sensors, while the 3 mV specified offset must be considered when the measured signal is small. The circuit should remain within the datasheet's input common-mode and output-swing limits, which vary with supply voltage. Suitable sensors include resistive bridges, temperature elements, and slow analog transducers whose bandwidth is well below the amplifier's capability.
추천
Industrial Control Error Amplifier
The two channels of LM358ADGKR can implement error amplification and an actuator-feedback stage in a basic industrial control system. A 30 V maximum supply rating provides useful voltage headroom for circuits referenced to higher-voltage control rails, and the 700 kHz bandwidth allows the loop to respond to many process-control dynamics rather than only static errors. The 3 mV offset specification should be included in the accuracy budget for low-level feedback signals. Compensation and stability components must be selected from the manufacturer application information for the selected closed-loop gain and load. Industrial temperature and isolation requirements should also be checked if the controller operates outside the device's 0 °C to +70 °C rating.
추천
Audio Preamplifier
LM358ADGKR can serve as a low-frequency audio preamplifier when its noise, offset, slew-rate, and output-drive requirements meet the source impedance and signal level. The 700 kHz gain-bandwidth product covers audio-band applications with moderate closed-loop gain, while two amplifiers allow independent gain and buffering stages in one package. Because the device is a general-purpose operational amplifier rather than a dedicated low-noise audio component, the complete input-noise and distortion behavior must be reviewed for high-fidelity paths. The 30 V maximum supply rating does not require a 30 V operating rail; selecting a lower supply can improve headroom and simplify output-swing design.
추천
Measurement Instrumentation Buffer
LM358ADGKR is useful for buffering a measurement source before a downstream converter or display input. One channel can provide impedance buffering, while the other can implement gain or active filtering, helping isolate the source from measurement-system loading. Its 700 kHz bandwidth is appropriate for many low-speed laboratory and industrial measurements, but offset error remains 3 mV as specified. Designers should calculate the closed-loop gain from the feedback resistors, check source impedance against the input-bias-current requirement, and maintain input and output voltages within the operating limits. The VSSOP-8 package supports compact analog boards while reducing the number of separate amplifier packages required.
추천
Power Supply Feedback Control
LM358ADGKR can amplify the error voltage between a power-supply feedback node and a reference, providing a compact control path for an external regulator topology. The dual channels can handle error amplification and output buffering, while the 30 V maximum supply rating supports control circuits connected to higher-voltage rails. The 700 kHz gain-bandwidth product is suitable for many moderate-bandwidth control loops, but compensation must be derived from the plant and must preserve phase margin. The 3 mV input offset contributes directly to the regulation error. This application requires careful common-mode-range, output-swing, and stability analysis rather than treating the amplifier as a fixed-voltage regulator.
추천
Interface and Filter Stage
LM358ADGKR can implement active filters and interface stages between sensors, logic families, or external transducers. Two channels permit a filter and a buffer to share one package, reducing board area in compact control systems. Its 700 kHz gain-bandwidth product supports filter frequencies well below the closed-loop bandwidth when appropriate resistor and capacitor values are selected. Component tolerances determine much of the actual filter accuracy, while the 3 mV offset can influence the DC operating point of a low-frequency active filter. Verify noise, input-bias current, common-mode range, and output drive against the source and load before finalizing the circuit.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM358ADGKR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM358DGKR | LM358ADGKRG4 |
|---|---|---|---|
| Package | VSSOP-8 (DGK) | VSSOP-8 (DGK) - same package | VSSOP-8 (DGK) - same package |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Channels | 2 channels | 2 channels | 2 channels |
| Maximum Supply Voltage | 30 V | 30 V nominal device family | 30 V nominal device family |
| Gain-Bandwidth Product | 700 kHz | 700 kHz nominal device family | 700 kHz nominal device family |
| Supply Configuration | Single or split supply | Single or split supply | Single or split supply |
| Mounting Type | Surface mount | Surface mount | Surface mount |
주요 차별점
- Two independent amplifier channels in one compact package (vs LM358ADGKRG4)
- Wide maximum supply rating for general-purpose analog systems (vs LM358DGKR)
- Single-package consolidation for two-stage signal chains (vs LM358ADGKRG4)
설계 노트
Decouple each supply connection with a local ceramic capacitor and connect the ground reference directly to the package ground pin. Keep the input, output, feedback, and ground paths compact because long traces can add parasitic resistance, inductance, and coupling. The manufacturer datasheet should be used for the recommended capacitor values, acceptable ceramic types, and the device's input and output current limits.
Do not assume that the 30 V maximum supply rating permits the input and output to swing across the full supply range. Check the input common-mode range and output-swing limits for the actual supply voltage, especially in low-voltage single-supply systems. Also avoid allowing either input to float; configure unused channels according to the manufacturer recommendation so they remain in a defined operating state.
Calculate closed-loop bandwidth from the 700 kHz gain-bandwidth product rather than treating that value as usable bandwidth at every gain. Higher closed-loop gain narrows the available bandwidth and can require noise-gain compensation. When driving capacitive loads, add isolation resistance or place the amplifier behind a suitable buffer, and verify stability experimentally rather than relying only on nominal bandwidth.
Use a compact analog layout with the bypass capacitor adjacent to the supply pin and a low-impedance ground plane or ground pour beneath the device. Route feedback components close to the relevant channel pins and keep sensitive input traces away from switching nodes and high-current paths. Because the package is VSSOP-8, verify land pattern dimensions and pin numbering against the manufacturer package drawing before fabrication.
규정 준수 정보
The manufacturer product page identifies LM358ADGKR, but no explicit target-part RoHS, REACH, halogen-free, lead-free, or conflict-minerals declaration is shown. The device is a general-purpose commercial amplifier rather than an AEC-Q100 automotive-qualified variant.