LMR341G-GTR - 2MHz Low-Power Ground-Sense Op Amp | ROHM
MPN: LMR341G-GTR ✓ 啟用中LMR341G-GTR 概覽
A ground-sense operational amplifier is a rail-to-rail-input-and-output amplifier optimized for measuring small voltages relative to ground. In the broader component hierarchy, it belongs to the operational-amplifier family, then to amplifier ICs and analog semiconductors. Its low-noise CMOS input stage provides low input bias current, while the full-swing output allows the amplifier to operate close to the positive or negative supply limits without requiring a separate output-bias arrangement.
The LMR341G combines a 2 MHz gain-bandwidth product with a 1 V/µs slew rate in a low 2.7 V to 5.5 V supply range. Typical supply current is 80 µA, reducing power consumption in continuously powered equipment. The shutdown function provides a controlled low-power operating state, while the low-bias MOSFET input stage helps minimize source-current loading on high-impedance sensors. These characteristics are particularly useful when sensing battery voltage, resistive sensor outputs, or low-level analog signals.
The amplifier is designed for general-purpose low-voltage analog signal conditioning. Its CMOS input stage supports low input bias current, and its output can swing fully across the supply range for improved measurement utilization. A 2 MHz bandwidth is adequate for sensor signals that do not require high-frequency signal processing, while the 1 V/µs slew rate allows the output to track moderate input steps without requiring a larger, higher-power package.
Typical uses include battery monitoring, portable instrumentation, sensor-interface circuits, industrial control modules, and low-voltage data-acquisition systems. In a battery-powered design, the shutdown pin can reduce consumption when the measurement function is not required. For high-impedance sensor nodes, the low input bias current helps avoid input-voltage errors caused by leakage through source impedances.
PCB implementation should keep the input and feedback components close to their corresponding pins, and the decoupling capacitor should be placed directly between the supply and ground pins. Because ground-sense accuracy depends on the reference plane, connect the sensor return and amplifier ground using a low-impedance layout. Avoid long input traces and unnecessary copper around high-impedance input nodes to reduce leakage and susceptibility to interference.
This page combines the manufacturer’s device description, distributor identification, electrical characteristics, package information, sourcing guidance, and practical design considerations. It also identifies family-level drop-in candidates while clearly separating confirmed functions from parameters that require final datasheet and qualification review before a design is released to production.
直接替換替代品,適用於 LMR341G-GTR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
LMR321G
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LMR331G
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LMR351G
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LMR361G
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LMR365G
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LMR341G-GTR 最大額定值與電氣特性
| Amplifier Type | Single CMOS operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 2 MHz |
| Slew Rate | 1 V/µs |
| 供應電流 | 80 µA typical |
| Output Current | 45 mA typical |
| Input Stage | MOSFET input |
| Output Swing | Full swing |
| Shutdown Function | Yes |
| 工作溫度範圍 | -40 °C to 85 °C |
| 封裝 | 6-pin SSOP |
| Packaging Option | Tape and reel |
| 安裝類型 | Surface mount |
LMR341G-GTR 6-pin ssop 腳位配置指南
LMR341G-GTR(6-pin ssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LMR341G-GTR.
請參閱 資料表 以查看完整腳位配置。
典型應用
LMR341G-GTR 適用於 6 應用s: Battery Voltage Monitoring, Portable Sensor Signal Conditioning, High-Impedance Sensor Interface, Low-Voltage Data Acquisition, Industrial Control Signal Conditioning, Battery-Powered Instrumentation.
Battery Voltage Monitoring
The LMR341G-GTR fits battery-powered voltage monitoring because it operates from 2.7 V to 5.5 V and draws 80 µA typical supply current. It can amplify a small voltage-divider signal referenced to ground while its full-swing output improves use of the available supply range. The MOSFET input stage presents low input bias current, reducing errors when the divider contains high-value resistors. Its shutdown function can also isolate the sensing path when measurements are not needed, helping reduce overall consumption in portable equipment.
推薦
Portable Sensor Signal Conditioning
For portable sensor interfaces, the LMR341G-GTR combines a 2 MHz gain-bandwidth product with a low-bias MOSFET input stage. This allows small sensor outputs to be amplified without loading the source heavily, while the 1 V/µs slew rate provides adequate response for many temperature, pressure, and light-sensor signals. Its 80 µA typical supply current is appropriate for continuously powered equipment, and shutdown control can be used during inactive measurement intervals.
推薦
High-Impedance Sensor Interface
The MOSFET input stage makes the LMR341G-GTR useful for high-impedance sensor nodes where input leakage could shift the measured voltage. With operation from 2.7 V to 5.5 V and a 2 MHz gain-bandwidth product, it can provide local gain close to the sensor while remaining within a compact 6-pin SSOP package. Keep input traces short, guard the sensitive node where appropriate, and confirm the actual input bias current in the manufacturer datasheet for the selected production lot and temperature range.
推薦
Low-Voltage Data Acquisition
The LMR341G-GTR is appropriate for conditioning channels in a compact low-voltage data-acquisition system. Its 2 MHz gain-bandwidth product supports moderate-bandwidth signals, and the 1 V/µs slew rate allows the output to follow changing sensor levels. The 6-pin SSOP format simplifies routing on space-constrained boards, while shutdown control can reduce power when selected channels are inactive. The amplifier should be paired with careful grounding and local supply bypassing to maintain accurate measurements.
推薦
Industrial Control Signal Conditioning
In an industrial control module, the LMR341G-GTR can condition low-level voltage inputs before they reach an analog-to-digital converter or controller. Its 2.7 V to 5.5 V range is compatible with common low-voltage control rails, and its full-swing output allows the signal to occupy more of the available analog range. The 80 µA typical supply current supports low-power auxiliary channels, while shutdown control can suppress a channel during inactive operating states.
推薦
Battery-Powered Instrumentation
The LMR341G-GTR supports portable instrumentation requiring low supply voltage and low quiescent consumption. Its 2.7 V lower operating limit accommodates single-cell-derived rails, while the 80 µA typical supply current limits amplifier overhead in continuously active measurement paths. The shutdown function can reduce consumption between readings, and the MOSFET input stage helps preserve the accuracy of high-impedance probes. Layout should prioritize a quiet ground reference and short feedback paths.
推薦
推薦產品摘要
工程參考資料,適用於 LMR341G-GTR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LMR321G | LMR331G | LMR351G | LMR361G | LMR365G |
|---|---|---|---|---|---|---|
| Brand | ROHM Semiconductor | ROHM Semiconductor | ROHM Semiconductor | ROHM Semiconductor | ROHM Semiconductor | ROHM Semiconductor |
| Package | 6-pin SSOP | 6-pin SSOP | 6-pin SSOP | 6-pin SSOP | 6-pin SSOP | 6-pin SSOP |
主要差異化特點
- Low-voltage operation with integrated shutdown (對比LMR331G)
- Low-power MOSFET-input ground-sense architecture (對比LMR321G)
- Balanced dynamic performance for sensor signals (對比LMR351G)
- Full-swing output improves analog range utilization (對比LMR361G)
設計說明
Place the supply bypass capacitor directly between the amplifier supply and ground pins, and keep the input and feedback traces short. Ground-sense accuracy depends on a low-impedance return path; route sensor ground and analog ground without current-sharing with motors, relays, or switching-converter returns. For a high-impedance sensor node, minimize exposed copper and use a suitable guard arrangement.
Estimated: with a 3.3 V supply and 80 µA typical supply current, amplifier supply consumption is approximately 0.264 mW before sensor and load current is included. This estimate uses 3.3 V and 80 µA and excludes output-current dissipation and external circuit losses. Shutdown can reduce consumption when the measurement path is not continuously required, but its active polarity must be confirmed from the manufacturer pin description.
Use feedback-gain values that preserve stability with the amplifier’s 2 MHz gain-bandwidth product and account for parasitic capacitance in the feedback network. The 1 V/µs slew rate supports moderate signal slopes, but very fast inputs can trigger slew-rate distortion. Avoid placing high-speed digital traces beneath sensitive input or feedback nodes, and use a quiet analog ground reference.
Do not assume every 6-pin amplifier in the same family has identical shutdown polarity, output behavior, or enable thresholds. Before substituting a family member, compare the official pin table, supply range, input common-mode limits, output swing, quiescent current, and package drawing. Also verify that the GTR ordering code represents the required tape-and-reel configuration for production.
合規資訊
The retrieved product information does not explicitly state the regulatory status of LMR341G-GTR. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations with ROHM before production release.