LMR341G-GTR - 2MHz Low-Power Ground-Sense Op Amp | ROHM
料号: LMR341G-GTR ✓ 量产中LMR341G-GTR 概述
A ground-sense operational amplifier is a rail-to-rail-input-and-output amplifier optimized for measuring small voltages relative to ground. In the broader component hierarchy, it belongs to the operational-amplifier family, then to amplifier ICs and analog semiconductors. Its low-noise CMOS input stage provides low input bias current, while the full-swing output allows the amplifier to operate close to the positive or negative supply limits without requiring a separate output-bias arrangement.
The LMR341G combines a 2 MHz gain-bandwidth product with a 1 V/µs slew rate in a low 2.7 V to 5.5 V supply range. Typical supply current is 80 µA, reducing power consumption in continuously powered equipment. The shutdown function provides a controlled low-power operating state, while the low-bias MOSFET input stage helps minimize source-current loading on high-impedance sensors. These characteristics are particularly useful when sensing battery voltage, resistive sensor outputs, or low-level analog signals.
The amplifier is designed for general-purpose low-voltage analog signal conditioning. Its CMOS input stage supports low input bias current, and its output can swing fully across the supply range for improved measurement utilization. A 2 MHz bandwidth is adequate for sensor signals that do not require high-frequency signal processing, while the 1 V/µs slew rate allows the output to track moderate input steps without requiring a larger, higher-power package.
Typical uses include battery monitoring, portable instrumentation, sensor-interface circuits, industrial control modules, and low-voltage data-acquisition systems. In a battery-powered design, the shutdown pin can reduce consumption when the measurement function is not required. For high-impedance sensor nodes, the low input bias current helps avoid input-voltage errors caused by leakage through source impedances.
PCB implementation should keep the input and feedback components close to their corresponding pins, and the decoupling capacitor should be placed directly between the supply and ground pins. Because ground-sense accuracy depends on the reference plane, connect the sensor return and amplifier ground using a low-impedance layout. Avoid long input traces and unnecessary copper around high-impedance input nodes to reduce leakage and susceptibility to interference.
This page combines the manufacturer’s device description, distributor identification, electrical characteristics, package information, sourcing guidance, and practical design considerations. It also identifies family-level drop-in candidates while clearly separating confirmed functions from parameters that require final datasheet and qualification review before a design is released to production.
直接替换替代料: LMR341G-GTR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
LMR321G
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LMR331G
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LMR351G
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LMR361G
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LMR365G
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LMR341G-GTR 最大额定值与电气特性
| Amplifier Type | Single CMOS operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 2 MHz |
| Slew Rate | 1 V/µs |
| 电源电流 | 80 µA typical |
| Output Current | 45 mA typical |
| Input Stage | MOSFET input |
| Output Swing | Full swing |
| Shutdown Function | Yes |
| 工作温度范围 | -40 °C to 85 °C |
| 封装 | 6-pin SSOP |
| Packaging Option | Tape and reel |
| 安装类型 | Surface mount |
LMR341G-GTR 6-pin ssop 引脚配置指南
LMR341G-GTR(6-pin ssop 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LMR341G-GTR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LMR341G-GTR 适用于 6 应用s: Battery Voltage Monitoring, Portable Sensor Signal Conditioning, High-Impedance Sensor Interface, Low-Voltage Data Acquisition, Industrial Control Signal Conditioning, Battery-Powered Instrumentation.
Battery Voltage Monitoring
The LMR341G-GTR fits battery-powered voltage monitoring because it operates from 2.7 V to 5.5 V and draws 80 µA typical supply current. It can amplify a small voltage-divider signal referenced to ground while its full-swing output improves use of the available supply range. The MOSFET input stage presents low input bias current, reducing errors when the divider contains high-value resistors. Its shutdown function can also isolate the sensing path when measurements are not needed, helping reduce overall consumption in portable equipment.
推荐
Portable Sensor Signal Conditioning
For portable sensor interfaces, the LMR341G-GTR combines a 2 MHz gain-bandwidth product with a low-bias MOSFET input stage. This allows small sensor outputs to be amplified without loading the source heavily, while the 1 V/µs slew rate provides adequate response for many temperature, pressure, and light-sensor signals. Its 80 µA typical supply current is appropriate for continuously powered equipment, and shutdown control can be used during inactive measurement intervals.
推荐
High-Impedance Sensor Interface
The MOSFET input stage makes the LMR341G-GTR useful for high-impedance sensor nodes where input leakage could shift the measured voltage. With operation from 2.7 V to 5.5 V and a 2 MHz gain-bandwidth product, it can provide local gain close to the sensor while remaining within a compact 6-pin SSOP package. Keep input traces short, guard the sensitive node where appropriate, and confirm the actual input bias current in the manufacturer datasheet for the selected production lot and temperature range.
推荐
Low-Voltage Data Acquisition
The LMR341G-GTR is appropriate for conditioning channels in a compact low-voltage data-acquisition system. Its 2 MHz gain-bandwidth product supports moderate-bandwidth signals, and the 1 V/µs slew rate allows the output to follow changing sensor levels. The 6-pin SSOP format simplifies routing on space-constrained boards, while shutdown control can reduce power when selected channels are inactive. The amplifier should be paired with careful grounding and local supply bypassing to maintain accurate measurements.
推荐
Industrial Control Signal Conditioning
In an industrial control module, the LMR341G-GTR can condition low-level voltage inputs before they reach an analog-to-digital converter or controller. Its 2.7 V to 5.5 V range is compatible with common low-voltage control rails, and its full-swing output allows the signal to occupy more of the available analog range. The 80 µA typical supply current supports low-power auxiliary channels, while shutdown control can suppress a channel during inactive operating states.
推荐
Battery-Powered Instrumentation
The LMR341G-GTR supports portable instrumentation requiring low supply voltage and low quiescent consumption. Its 2.7 V lower operating limit accommodates single-cell-derived rails, while the 80 µA typical supply current limits amplifier overhead in continuously active measurement paths. The shutdown function can reduce consumption between readings, and the MOSFET input stage helps preserve the accuracy of high-impedance probes. Layout should prioritize a quiet ground reference and short feedback paths.
推荐
推荐产品汇总
工程参考数据: LMR341G-GTR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LMR321G | LMR331G | LMR351G | LMR361G | LMR365G |
|---|---|---|---|---|---|---|
| Brand | ROHM Semiconductor | ROHM Semiconductor | ROHM Semiconductor | ROHM Semiconductor | ROHM Semiconductor | ROHM Semiconductor |
| Package | 6-pin SSOP | 6-pin SSOP | 6-pin SSOP | 6-pin SSOP | 6-pin SSOP | 6-pin SSOP |
关键差异点
- Low-voltage operation with integrated shutdown (对比 LMR331G)
- Low-power MOSFET-input ground-sense architecture (对比 LMR321G)
- Balanced dynamic performance for sensor signals (对比 LMR351G)
- Full-swing output improves analog range utilization (对比 LMR361G)
设计说明
Place the supply bypass capacitor directly between the amplifier supply and ground pins, and keep the input and feedback traces short. Ground-sense accuracy depends on a low-impedance return path; route sensor ground and analog ground without current-sharing with motors, relays, or switching-converter returns. For a high-impedance sensor node, minimize exposed copper and use a suitable guard arrangement.
Estimated: with a 3.3 V supply and 80 µA typical supply current, amplifier supply consumption is approximately 0.264 mW before sensor and load current is included. This estimate uses 3.3 V and 80 µA and excludes output-current dissipation and external circuit losses. Shutdown can reduce consumption when the measurement path is not continuously required, but its active polarity must be confirmed from the manufacturer pin description.
Use feedback-gain values that preserve stability with the amplifier’s 2 MHz gain-bandwidth product and account for parasitic capacitance in the feedback network. The 1 V/µs slew rate supports moderate signal slopes, but very fast inputs can trigger slew-rate distortion. Avoid placing high-speed digital traces beneath sensitive input or feedback nodes, and use a quiet analog ground reference.
Do not assume every 6-pin amplifier in the same family has identical shutdown polarity, output behavior, or enable thresholds. Before substituting a family member, compare the official pin table, supply range, input common-mode limits, output swing, quiescent current, and package drawing. Also verify that the GTR ordering code represents the required tape-and-reel configuration for production.
合规信息
The retrieved product information does not explicitly state the regulatory status of LMR341G-GTR. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations with ROHM before production release.