LT1213MJ8 - Dual 28MHz Precision Op Amp | Analog Devices
MPN: LT1213MJ8 ✗ 停產LT1213MJ8 概覽
An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sources, compare voltages, and drive feedback networks. Within the electronics hierarchy, the LT1213 belongs to the amplifier IC category, where precision and speed determine whether it is appropriate for instrumentation, audio, communications, or control applications. Its dual configuration provides two independent amplifiers in one package while reducing board area compared with separate single devices.
Key features include a typical 28 MHz gain-bandwidth product and 12 V/µs slew rate. The device settles to 0.01% after a 2 V step with 200 µV error in approximately 500 ns, while a 10 V step settles to 1 mV in approximately 1.1 µs. These figures make it useful where both small-signal accuracy and rapid transient response are required rather than low-noise-only operation.
The LT1213 architecture emphasizes DC precision, allowing many systems to operate without amplifier trim adjustments. Its single-supply capability simplifies rail-to-rail-compatible interface design when the signal and supply ranges are compatible with the input and output limits. The 28 MHz bandwidth also permits operation at higher closed-loop gains while retaining useful loop bandwidth and phase margin.
Typical applications include 12-bit systems with a 2.5 V full scale, 16-bit systems with a 10 V full scale, active filters, and photodiode amplifiers. The dual package is also useful for instrumentation requiring two amplified channels, such as differential signal conditioning or a gain stage paired with an active filter.
When laying out the LT1213MJ8, use short feedback paths, maintain symmetric routing around the amplifier pins, and place compensation or filter capacitors according to the manufacturer application guidance. Decouple each supply rail close to the device and avoid routing high-current return paths through sensitive analog ground connections.
This page combines the LT1213 family specifications, package details, application guidance, practical design notes, and available same-family replacement choices into a design-focused reference for engineers evaluating the LT1213MJ8 in military, industrial, and precision analog systems.
直接替換替代品,適用於 LT1213MJ8 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
LT1213ACN8
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LT1213CN8
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LT1213IN8
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LT1213MJ8 最大額定值與電氣特性
| Amplifier Type | Dual precision operational amplifier |
| Number of Circuits | 2 circuits |
| Gain-Bandwidth Product | 28 MHz typical |
| Slew Rate | 12 V/µs typical |
| Maximum Supply Voltage | ±18 V / 36 V total |
| Supply Type | Single supply |
| 0.01% Settling Time | 500 ns typical for a 2 V step with 200 µV error |
| 1 mV Settling Time | 1.1 µs typical for a 10 V step |
| 封裝 | 8-pin CERDIP |
| Package Type | Ceramic dual in-line through-hole package |
| Terminal Count | 8 terminals |
| 安裝類型 | Through-hole |
| Temperature Grade | Military |
LT1213MJ8 ceramic dual in-line through-hole package 腳位配置指南
LT1213MJ8(ceramic dual in-line through-hole package 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LT1213MJ8.
請參閱 資料表 以查看完整腳位配置。
典型應用
LT1213MJ8 適用於 6 應用s: Precision Data-Conversion Front End, Photodiode Signal Conditioning, Active Filter Implementation, Instrumentation Signal Buffering, Communications Receive Chain, Low-Level Pulse Amplification.
Precision Data-Conversion Front End
The LT1213MJ8 fits precision acquisition paths because its 28 MHz typical gain-bandwidth product and 12 V/µs typical slew rate support fast settling while retaining DC precision. The manufacturer identifies both 2.5 V full-scale 12-bit systems and 10 V full-scale 16-bit systems as LT1213 applications. Each amplifier can condition a separate input or serve as a post-amplifier following a converter driver. The key design consideration is gain-bandwidth allocation: higher closed-loop gains reduce available loop bandwidth, so verify stability, noise, and output settling against the actual filter and converter timing. A ceramic dual in-line package also favors rugged through-hole laboratory, industrial, and military equipment rather than compact surface-mount products.
推薦
Photodiode Signal Conditioning
The LT1213MJ8 is suitable for photodiode amplification because the manufacturer lists photodiode amplifiers among the principal LT1213 applications. A 28 MHz typical gain-bandwidth product preserves pulse-edge information, while the approximately 500 ns settling time for a 2 V step to 200 µV error helps recover rapidly after transients. Its dual configuration can process a detector and reference channel or two sensors in a compact through-hole implementation. The principal trade-off is that fast voltage feedback does not eliminate all detector constraints; input bias current, input-voltage noise, capacitance, and photodiode leakage must be checked against the source impedance. Compensation capacitance should be selected using the manufacturer’s stability guidance for the intended gain and load.
推薦
Active Filter Implementation
The LT1213MJ8 supports active-filter designs where the 28 MHz gain-bandwidth product leaves useful bandwidth above the filter corner frequency, while its 12 V/µs typical slew rate improves large-signal behavior. The manufacturer specifically identifies active filters as an LT1213 application. Two amplifiers in one package allow a second-order section and an additional gain or buffer stage without using separate dual packages. Component tolerances and amplifier open-loop behavior affect the realized cutoff, attenuation, and phase response, so simulate the complete filter before fabrication. Keep the feedback components and routing compact to reduce parasitic coupling, and verify output swing against the largest transient expected at the filter output. The military-grade ceramic package is useful in rugged systems where long service intervals and through-hole assembly are preferred.
推薦
Instrumentation Signal Buffering
The LT1213MJ8 is well suited to instrumentation buffering because the LT1213 family emphasizes DC precision and can operate from a single supply. Its 28 MHz bandwidth permits closed-loop gains commonly used for sensor conditioning without placing the amplifier deep into its low-frequency regime. The dual architecture supports a differential pair with one amplifier handling each side, or separates gain and buffer stages in a multichannel board. Designers should verify input common-mode range, output swing, offset error, and bias current for the actual sensor excitation. Keep input leads short, use a quiet return path, and avoid placing sensitive high-impedance traces beside the 12 V/µs output nodes. These practices reduce errors that are significant when precision rather than bandwidth is the primary measurement objective.
推薦
Communications Receive Chain
The LT1213MJ8 can support communications receive chains where 28 MHz bandwidth and a 12 V/µs slew rate are needed to preserve amplitude and edge information. Its precision DC characteristics also make it useful ahead of filtering or demodulation stages rather than only as a wideband driver. The dual package permits two channels or a gain stage and an antialias filter. Adequate supply bypassing and controlled board geometry are essential because fast output current can couple through supply and ground impedance. Check the output-current demand into the following stage and confirm that the selected feedback network remains stable with realistic capacitive loading. For battery-powered or highly integrated systems, a lower-power family may be more appropriate when the 28 MHz bandwidth is not required.
推薦
Low-Level Pulse Amplification
The LT1213MJ8 is appropriate for amplifying short, low-level pulses when fast recovery and stable output settling are more important than minimum noise density. The specified 10 V step settles to 1 mV in approximately 1.1 µs, while the 2 V step reaches the finer 0.01% criterion in approximately 500 ns. That behavior can reduce distortion when a sensor returns rapidly to baseline. Place the amplifier close to the source to minimize parasitic capacitance and pickup, and use a local bypass capacitor on each supply connection. A resistive feedback network must be checked for parasitic oscillation, and the output must remain within its voltage swing during the pulse. The ceramic military-grade package is advantageous for field equipment requiring robust through-hole construction.
推薦
推薦產品摘要
工程參考資料,適用於 LT1213MJ8 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LT1213ACN8 | LT1213CN8 | LT1213IN8 |
|---|---|---|---|---|
| Package | 8-pin CERDIP | 8-pin CERDIP | 8-pin CERDIP | 8-pin CERDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Configuration | Dual | Dual | Dual | Dual |
| Gain-Bandwidth Product | 28 MHz typical | 28 MHz typical | 28 MHz typical | 28 MHz typical |
| Slew Rate | 12 V/µs typical | 12 V/µs typical | 12 V/µs typical | 12 V/µs typical |
| 0.01% Settling for 2 V Step | 500 ns typical with 200 µV error | 500 ns typical with 200 µV error | 500 ns typical with 200 µV error | 500 ns typical with 200 µV error |
| 1 mV Settling for 10 V Step | 1.1 µs typical | 1.1 µs typical | 1.1 µs typical | 1.1 µs typical |
| Temperature Grade | Military | ACN8 grade designation | CN8 grade designation | IN8 grade designation |
主要差異化特點
- Maintains the core LT1213 dynamic specifications (對比LT1213CN8)
- Provides fast recovery after large signal steps (對比LT1213IN8)
- Combines dual precision channels with a military-grade designation (對比LT1213ACN8)
設計說明
Place input, feedback, and decoupling connections close to the LT1213MJ8 pins. A high-speed voltage-feedback amplifier can form unintended feedback loops when long traces add phase shift. Route each supply connection directly to local bypass capacitance and connect the bypass return to the quiet ground reference without sharing narrow paths with output-current returns. The manufacturer’s LT1213 application guidance and the package pin table should be used for final trace placement.
Treat the two amplifier channels as separate high-speed signal paths. Keep feedback resistors close to the output and input pins, avoid vias in sensitive feedback loops, and place optional compensation capacitors at the amplifier pins. If the source has high capacitance or the load is capacitive, check loop stability using the manufacturer’s recommended compensation values. The 12 V/µs slew rate can generate high edge current, so grounding and supply-return geometry should minimize common-impedance noise.
Do not treat a 28 MHz gain-bandwidth product as unlimited usable bandwidth at every closed-loop gain. Account for the gain error and phase margin introduced by the feedback network, verify output swing and output-current capability, and ensure the input common-mode range includes the complete signal excursion. The LT1213 family’s single-supply operation does not make the amplifier automatically rail-to-rail at the input or output, so both limits must be checked for the actual supply configuration.
Use the 8-pin CERDIP footprint with adequate hole and lead-clearance tolerances for the chosen board process. Keep sensitive analog inputs away from the opposite amplifier’s output and supply pins, especially when one channel handles a fast transient and the other measures a small signal. Confirm the exact pin numbering against the manufacturer package drawing before fabrication, particularly when using any LT1213 family ordering suffix as a mechanical or electrical substitute.
合規資訊
The military-grade suffix identifies the device temperature grade, not automotive qualification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or applicable material declaration.