Analog Devices

LT1213MJ8 - Dual 28MHz Precision Op Amp | Analog Devices

MPN: LT1213MJ8 ✗ Akhir Hayat
±18 V / 36 V total Vdss 8-pin CERDIP Package
MOQ: 1 |

LT1213MJ8 Ringkasan

Analog Devices LT1213MJ8 is a dual, single-supply precision operational amplifier with a 28 MHz gain-bandwidth product, 12 V/µs slew rate, and military-grade 8-pin CERDIP package. The LT1213 family combines two amplifiers with DC precision, fast settling, and an operating range extending to ±18 V, making it suitable for instrumentation, active filtering, photodiode signal conditioning, and precision data-conversion systems.

An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sources, compare voltages, and drive feedback networks. Within the electronics hierarchy, the LT1213 belongs to the amplifier IC category, where precision and speed determine whether it is appropriate for instrumentation, audio, communications, or control applications. Its dual configuration provides two independent amplifiers in one package while reducing board area compared with separate single devices.

Key features include a typical 28 MHz gain-bandwidth product and 12 V/µs slew rate. The device settles to 0.01% after a 2 V step with 200 µV error in approximately 500 ns, while a 10 V step settles to 1 mV in approximately 1.1 µs. These figures make it useful where both small-signal accuracy and rapid transient response are required rather than low-noise-only operation.

The LT1213 architecture emphasizes DC precision, allowing many systems to operate without amplifier trim adjustments. Its single-supply capability simplifies rail-to-rail-compatible interface design when the signal and supply ranges are compatible with the input and output limits. The 28 MHz bandwidth also permits operation at higher closed-loop gains while retaining useful loop bandwidth and phase margin.

Typical applications include 12-bit systems with a 2.5 V full scale, 16-bit systems with a 10 V full scale, active filters, and photodiode amplifiers. The dual package is also useful for instrumentation requiring two amplified channels, such as differential signal conditioning or a gain stage paired with an active filter.

When laying out the LT1213MJ8, use short feedback paths, maintain symmetric routing around the amplifier pins, and place compensation or filter capacitors according to the manufacturer application guidance. Decouple each supply rail close to the device and avoid routing high-current return paths through sensitive analog ground connections.

This page combines the LT1213 family specifications, package details, application guidance, practical design notes, and available same-family replacement choices into a design-focused reference for engineers evaluating the LT1213MJ8 in military, industrial, and precision analog systems.

Pilihan pengganti yang segera untuk LT1213MJ8 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

LT1213ACN8

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 8-pin CERDIP
Same LT1213 core electrical performance and 8-pin pinout, but the ACN8 temperature-grade suffix differs from the military MJ8 designation; core bandwidth and slew-rate deltas are 0%.

📋 Alternatif rujukan (tidak dalam katalog)

LT1213CN8

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 8-pin CERDIP
Same LT1213 core electrical performance and 8-pin pinout, but the CN8 temperature-grade suffix differs from the military MJ8 designation; core bandwidth and slew-rate deltas are 0%.

📋 Alternatif rujukan (tidak dalam katalog)

LT1213IN8

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 8-pin CERDIP
Same LT1213 core electrical performance and 8-pin pinout, but the IN8 temperature-grade suffix differs from the military MJ8 designation; core bandwidth and slew-rate deltas are 0%.

📋 Alternatif rujukan (tidak dalam katalog)

LT1213MJ8 Penilaian maksimum & Ciri-ciri Elektrik

Amplifier Type Dual precision operational amplifier
Number of Circuits 2 circuits
Gain-Bandwidth Product 28 MHz typical
Slew Rate 12 V/µs typical
Maximum Supply Voltage ±18 V / 36 V total
Supply Type Single supply
0.01% Settling Time 500 ns typical for a 2 V step with 200 µV error
1 mV Settling Time 1.1 µs typical for a 10 V step
Kemasan 8-pin CERDIP
Package Type Ceramic dual in-line through-hole package
Terminal Count 8 terminals
Jenis Pemasangan Through-hole
Temperature Grade Military

Panduan Konfigurasi Pin LT1213MJ8 ceramic dual in-line through-hole package

Konfigurasi pin untuk LT1213MJ8 (ceramic dual in-line through-hole package pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai ceramic dual in-line through-hole package untuk LT1213MJ8

Tiada data garisan pin yang diperoleh untuk LT1213MJ8.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

LT1213MJ8 patut untuk 6 aplikasis: Precision Data-Conversion Front End, Photodiode Signal Conditioning, Active Filter Implementation, Instrumentation Signal Buffering, Communications Receive Chain, Low-Level Pulse Amplification.

📺

Precision Data-Conversion Front End

The LT1213MJ8 fits precision acquisition paths because its 28 MHz typical gain-bandwidth product and 12 V/µs typical slew rate support fast settling while retaining DC precision. The manufacturer identifies both 2.5 V full-scale 12-bit systems and 10 V full-scale 16-bit systems as LT1213 applications. Each amplifier can condition a separate input or serve as a post-amplifier following a converter driver. The key design consideration is gain-bandwidth allocation: higher closed-loop gains reduce available loop bandwidth, so verify stability, noise, and output settling against the actual filter and converter timing. A ceramic dual in-line package also favors rugged through-hole laboratory, industrial, and military equipment rather than compact surface-mount products.

🎥

Photodiode Signal Conditioning

The LT1213MJ8 is suitable for photodiode amplification because the manufacturer lists photodiode amplifiers among the principal LT1213 applications. A 28 MHz typical gain-bandwidth product preserves pulse-edge information, while the approximately 500 ns settling time for a 2 V step to 200 µV error helps recover rapidly after transients. Its dual configuration can process a detector and reference channel or two sensors in a compact through-hole implementation. The principal trade-off is that fast voltage feedback does not eliminate all detector constraints; input bias current, input-voltage noise, capacitance, and photodiode leakage must be checked against the source impedance. Compensation capacitance should be selected using the manufacturer’s stability guidance for the intended gain and load.

📡

Active Filter Implementation

The LT1213MJ8 supports active-filter designs where the 28 MHz gain-bandwidth product leaves useful bandwidth above the filter corner frequency, while its 12 V/µs typical slew rate improves large-signal behavior. The manufacturer specifically identifies active filters as an LT1213 application. Two amplifiers in one package allow a second-order section and an additional gain or buffer stage without using separate dual packages. Component tolerances and amplifier open-loop behavior affect the realized cutoff, attenuation, and phase response, so simulate the complete filter before fabrication. Keep the feedback components and routing compact to reduce parasitic coupling, and verify output swing against the largest transient expected at the filter output. The military-grade ceramic package is useful in rugged systems where long service intervals and through-hole assembly are preferred.

🏭

Instrumentation Signal Buffering

The LT1213MJ8 is well suited to instrumentation buffering because the LT1213 family emphasizes DC precision and can operate from a single supply. Its 28 MHz bandwidth permits closed-loop gains commonly used for sensor conditioning without placing the amplifier deep into its low-frequency regime. The dual architecture supports a differential pair with one amplifier handling each side, or separates gain and buffer stages in a multichannel board. Designers should verify input common-mode range, output swing, offset error, and bias current for the actual sensor excitation. Keep input leads short, use a quiet return path, and avoid placing sensitive high-impedance traces beside the 12 V/µs output nodes. These practices reduce errors that are significant when precision rather than bandwidth is the primary measurement objective.

🌐

Communications Receive Chain

The LT1213MJ8 can support communications receive chains where 28 MHz bandwidth and a 12 V/µs slew rate are needed to preserve amplitude and edge information. Its precision DC characteristics also make it useful ahead of filtering or demodulation stages rather than only as a wideband driver. The dual package permits two channels or a gain stage and an antialias filter. Adequate supply bypassing and controlled board geometry are essential because fast output current can couple through supply and ground impedance. Check the output-current demand into the following stage and confirm that the selected feedback network remains stable with realistic capacitive loading. For battery-powered or highly integrated systems, a lower-power family may be more appropriate when the 28 MHz bandwidth is not required.

✈️

Low-Level Pulse Amplification

The LT1213MJ8 is appropriate for amplifying short, low-level pulses when fast recovery and stable output settling are more important than minimum noise density. The specified 10 V step settles to 1 mV in approximately 1.1 µs, while the 2 V step reaches the finer 0.01% criterion in approximately 500 ns. That behavior can reduce distortion when a sensor returns rapidly to baseline. Place the amplifier close to the source to minimize parasitic capacitance and pickup, and use a local bypass capacitor on each supply connection. A resistive feedback network must be checked for parasitic oscillation, and the output must remain within its voltage swing during the pulse. The ceramic military-grade package is advantageous for field equipment requiring robust through-hole construction.

Ringkasan Produk Disebarkan

LT1213 Same dual amplifier family Dipergunakan di: Precision Data-Conversion Front End, Photodiode Signal Conditioning, Active Filter Implementation, Instrumentation Signal Buffering, Communications Receive Chain, Low-Level Pulse Amplification LT1214 Quad version of the same amplifier family Dipergunakan di: Precision Data-Conversion Front End, Active Filter Implementation LT1211 Lower-power related precision amplifier family Dipergunakan di: Photodiode Signal Conditioning LT1212 Related lower-speed precision amplifier family Dipergunakan di: Instrumentation Signal Buffering LT1215 Higher-speed related amplifier family Dipergunakan di: Communications Receive Chain, Low-Level Pulse Amplification LT1216 Higher-speed related amplifier family Dipergunakan di: Communications Receive Chain
What is the LT1213MJ8?
The LT1213MJ8 is a dual precision operational amplifier with two amplifiers in one 8-pin CERDIP package. According to the Analog Devices LT1213 product page, the family provides a 28 MHz typical gain-bandwidth product and a 12 V/µs typical slew rate. The MJ8 ordering code identifies a military-grade ceramic dual in-line package suitable for through-hole precision analog designs where fast settling and low DC error are important.
What is the gain-bandwidth product and slew rate of LT1213MJ8?
The LT1213MJ8 has a 28 MHz typical gain-bandwidth product and a 12 V/µs typical slew rate. According to the Analog Devices LT1213 product information, these speed specifications permit accurate operation well beyond audio frequencies while still supporting feedback networks with moderate closed-loop gains. Designers should verify loop stability and output-current requirements for the selected gain and load.
What is the settling performance of the LT1213MJ8?
The LT1213 family settles to 0.01% within approximately 500 ns after a 2 V step with 200 µV error. According to the LT1213 datasheet, it also settles to 1 mV within approximately 1.1 µs after a 10 V step. These figures make the LT1213MJ8 appropriate for pulse-processing and data-acquisition paths requiring rapid recovery after a large input transition.
Can the LT1213MJ8 operate from a single supply?
Yes, the LT1213MJ8 is specified as a single-supply precision operational amplifier, and the family supports an operating range extending to ±18 V. According to the Analog Devices LT1213 product page, single-supply operation simplifies circuit design when signals remain within the amplifier’s input and output ranges. The exact common-mode limits and output swing should be checked against the selected rail voltages in the manufacturer datasheet.
Where can I download the LT1213MJ8 datasheet PDF?
The LT1213MJ8 datasheet and product information are available through the official Analog Devices LT1213 product page at https://www.analog.com/en/products/lt1213.html. The manufacturer page provides the authoritative electrical characteristics, ordering information, package drawings, and typical application material. Use the MJ8 ordering details in the datasheet to confirm ceramic-package and military-grade requirements before releasing a design.
Where is the LT1213MJ8 pinout?
The LT1213MJ8 pinout is shown in the pin-configuration section of the Analog Devices LT1213 datasheet and its 8-pin CERDIP package drawing. The device contains two complete operational amplifiers, including their offset inputs, outputs, supply pins, and offset-null functions. Use the manufacturer pin-description table when assigning PCB tracks rather than inferring connections from a generic dual-op-amp outline.
What can replace the LT1213MJ8?
The closest drop-in choices are the LT1213 family members that retain the same 8-pin CERDIP footprint and pin arrangement, including LT1213ACN8, LT1213CN8, and LT1213IN8. The LT1213MJ8 is the military-grade option, so replacement selection should consider temperature grade, ceramic-package construction, screening, and procurement requirements rather than bandwidth alone.
Is LT1213MJ8 the same as LT1213IN8?
No, the LT1213MJ8 and LT1213IN8 share the core LT1213 amplifier performance and an 8-pin dual in-line footprint, but their ordering codes identify different temperature and package grades. The LT1213MJ8 is a military-grade CERDIP device, whereas LT1213IN8 denotes a different grade. Confirm the required environmental rating and package construction before treating either device as an interchangeable procurement option.
LT1213MJ8 vs LT1213CN8 — which should I choose?
Choose LT1213MJ8 when the design requires the military-grade LT1213 option and ceramic dual in-line construction. Choose LT1213CN8 when that grade meets the application and a lower-cost commercial ceramic-package option is appropriate. Both belong to the same LT1213 family and share the core 28 MHz gain-bandwidth and 12 V/µs slew-rate characteristics, but their environmental and ordering requirements differ.
When should I choose LT1213MJ8 over another dual op amp?
Choose LT1213MJ8 when the design combines a dual amplifier, fast settling, a 28 MHz typical gain-bandwidth product, and a military-grade ceramic DIP requirement. It is a stronger fit than a general-purpose precision op amp when large-signal recovery speed matters. A slower amplifier may be preferable for ultralow-noise, micropower, or low-cost surface-mount applications where speed is unnecessary.
Is LT1213MJ8 suitable for photodiode amplification?
Yes, the LT1213MJ8 is suitable for photodiode and other low-level transducer amplification because the manufacturer identifies photodiode amplifiers as an LT1213 application. Its dual configuration can support two detector channels, while the 28 MHz bandwidth and 500 ns typical 0.01% settling specification help preserve pulse fidelity. Input bias current, input capacitance, and noise must still be checked against the detector source.
What is the best Analog Devices equivalent for LT1213MJ8?
The best family-based equivalent depends on the required qualification and package grade rather than on amplifier function alone. LT1213ACN8, LT1213CN8, and LT1213IN8 are same-family 8-pin dual in-line options, while LT1213MJ8 remains the military-grade CERDIP selection. The official LT1213 ordering table should determine which suffix satisfies the required temperature grade, package, and qualification level.
Where can I buy LT1213MJ8 and what is its price?
Use the Request a Quote form on this page to request LT1213MJ8 pricing, current availability, and lead time for the exact military-grade 8-pin CERDIP ordering code. The manufacturer product page identifies the device family, but live commercial terms can change and are therefore handled through the quote workflow. Confirm the package suffix and temperature grade when submitting the request.
What is the lead time for LT1213MJ8?
Request the current LT1213MJ8 lead time and minimum order quantity through the Request a Quote form on this page. Lead time depends on manufacturer inventory, the exact ordering suffix, qualification requirements, and order volume. The military-grade MJ8 configuration should be quoted separately from standard commercial LT1213 variants to avoid receiving a functionally similar but incorrectly graded device.
Is LT1213MJ8 currently in stock?
Current LT1213MJ8 inventory should be confirmed through the Request a Quote form on this page rather than inferred from a general product listing. Include the exact 8-pin CERDIP military-grade suffix and your required quantity in the request. This also lets the supplier confirm whether any available material matches the required LT1213 ordering code and environmental grade.
What are the key specifications of LT1213MJ8 that engineers should know?
The LT1213MJ8 combines two precision amplifiers, a 28 MHz typical gain-bandwidth product, a 12 V/µs typical slew rate, and fast settling in an 8-pin military-grade CERDIP package. According to Analog Devices, the 0.01% settling time is approximately 500 ns for a 2 V step with 200 µV error, while a 10 V step reaches 1 mV in approximately 1.1 µs. Its maximum supply rating is ±18 V, or 36 V total.

Data referensi kejuruteraan untuk LT1213MJ8 — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose LT1213MJ8 when the system requires a dual precision amplifier with fast settling, a military-grade ordering designation, and an 8-pin CERDIP package. LT1213ACN8, LT1213CN8, and LT1213IN8 share the core LT1213 amplifier performance and package family, so they may simplify sourcing when their individual temperature-grade and qualification requirements are acceptable. The principal decision is therefore environmental grade, package construction, qualification, and availability rather than bandwidth or slew rate. For designs that do not require a ceramic through-hole package, evaluate surface-mount dual amplifiers instead; they are not pin-to-pin substitutes and require a different PCB layout. Similarly, choose a lower-power or higher-speed amplifier family when current consumption, noise density, or slew-rate requirements differ materially from the LT1213 performance profile.

Perbandingan dengan Gantian

Parametr Produk Ini LT1213ACN8 LT1213CN8 LT1213IN8
Package 8-pin CERDIP 8-pin CERDIP 8-pin CERDIP 8-pin CERDIP
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Amplifier Configuration Dual Dual Dual Dual
Gain-Bandwidth Product 28 MHz typical 28 MHz typical 28 MHz typical 28 MHz typical
Slew Rate 12 V/µs typical 12 V/µs typical 12 V/µs typical 12 V/µs typical
0.01% Settling for 2 V Step 500 ns typical with 200 µV error 500 ns typical with 200 µV error 500 ns typical with 200 µV error 500 ns typical with 200 µV error
1 mV Settling for 10 V Step 1.1 µs typical 1.1 µs typical 1.1 µs typical 1.1 µs typical
Temperature Grade Military ACN8 grade designation CN8 grade designation IN8 grade designation

Penyeberangsung Jelas

  • Maintains the core LT1213 dynamic specifications (vsLT1213CN8)
  • Provides fast recovery after large signal steps (vsLT1213IN8)
  • Combines dual precision channels with a military-grade designation (vsLT1213ACN8)

Catatan Desain

Place input, feedback, and decoupling connections close to the LT1213MJ8 pins. A high-speed voltage-feedback amplifier can form unintended feedback loops when long traces add phase shift. Route each supply connection directly to local bypass capacitance and connect the bypass return to the quiet ground reference without sharing narrow paths with output-current returns. The manufacturer’s LT1213 application guidance and the package pin table should be used for final trace placement.

Treat the two amplifier channels as separate high-speed signal paths. Keep feedback resistors close to the output and input pins, avoid vias in sensitive feedback loops, and place optional compensation capacitors at the amplifier pins. If the source has high capacitance or the load is capacitive, check loop stability using the manufacturer’s recommended compensation values. The 12 V/µs slew rate can generate high edge current, so grounding and supply-return geometry should minimize common-impedance noise.

Do not treat a 28 MHz gain-bandwidth product as unlimited usable bandwidth at every closed-loop gain. Account for the gain error and phase margin introduced by the feedback network, verify output swing and output-current capability, and ensure the input common-mode range includes the complete signal excursion. The LT1213 family’s single-supply operation does not make the amplifier automatically rail-to-rail at the input or output, so both limits must be checked for the actual supply configuration.

Use the 8-pin CERDIP footprint with adequate hole and lead-clearance tolerances for the chosen board process. Keep sensitive analog inputs away from the opposite amplifier’s output and supply pins, especially when one channel handles a fast transient and the other measures a small signal. Confirm the exact pin numbering against the manufacturer package drawing before fabrication, particularly when using any LT1213 family ordering suffix as a mechanical or electrical substitute.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The military-grade suffix identifies the device temperature grade, not automotive qualification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or applicable material declaration.

Pencarian Berhubungan

LT1213MJ8 datasheet LT1213MJ8 datasheet pdf LT1213MJ8 pinout LT1213MJ8 equivalent LT1213MJ8 replacement LT1213MJ8 cross reference LT1213MJ8 vs LT1213CN8 LT1213MJ8 footprint LT1213MJ8 price Analog Devices LT1213MJ8 LT1213MJ8 8-pin CERDIP LT1213 28MHz dual precision op amp

Komponen dan Tanda berkaitan

Analog Devices Linear Technology LT1213MJ8 LT1213 LT1214 LT1211 LT1212 LT1215 LT1216 LT1213ACN8 LT1213CN8 LT1213IN8 operational amplifier precision amplifier dual amplifier amplifier IC gain-bandwidth product slew rate settling time single-supply amplifier 8-pin CERDIP ceramic dual in-line package through-hole package active filter photodiode amplifier
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ