LT1357CN8 - 25MHz 600V/us Voltage-Feedback Op Amp | ADI
MPN: LT1357CN8 ✓ 啟用中LT1357CN8 概覽
A voltage-feedback operational amplifier is a general-purpose analog building block that amplifies the difference between its inverting and non-inverting inputs. Within the broader IC hierarchy, it belongs to the amplifier IC class, performs closed-loop signal conditioning, and can operate as a voltage amplifier, current buffer, comparator with an external bias arrangement, or a driver for downstream analog and mixed-signal circuits.
Key characteristics include a 25 MHz gain-bandwidth product, a 600 V/us slew rate, and approximately 30 mA supply current. According to the Analog Devices LT1357 datasheet, the device provides lower supply current, lower input offset voltage, lower input bias current, and higher DC gain than amplifiers with comparable bandwidth. These properties make it useful where accurate small-signal behavior must coexist with rapid large-signal transitions.
The LT1357 uses a voltage-feedback topology optimized for conventional gain-setting networks. Its high speed makes gain-bandwidth and slew-rate limits important in pulse, video, instrumentation, and feedback-control systems. The 8-pin PDIP package supports through-hole assembly and prototyping, while the single-amplifier configuration leaves two spare inputs available for grounding or shielding.
Typical uses include low-level signal conditioning, current-to-voltage conversion, active filtering, analog instrumentation, and pulse-shaping stages. The 600 V/us slew rate supports faster edge reproduction than many general-purpose amplifiers, while the 25 MHz bandwidth covers applications extending into the low megahertz range.
When designing a board around the LT1357CN8, follow the datasheet pinout and decoupling recommendations closely. Keep input and feedback traces short, provide clean supply bypassing, and account for resistor loading when calculating closed-loop gain and bandwidth.
This page consolidates the manufacturer specifications, package details, equivalent-part information, and practical design guidance into one engineering reference for evaluating the LT1357CN8 in new amplifier designs.
直接替換替代品,適用於 LT1357CN8 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
LT1357CN8#PBF
✅ 直接替換📋 參考替代品(不在目錄中)
LT1357CN8 最大額定值與電氣特性
| Amplifier Type | Voltage Feedback |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 25 MHz |
| Slew Rate | 600 V/us |
| 供應電流 | 30 mA |
| 封裝 | 8-pin PDIP, 7.62 mm lead pitch |
| Package Length | 7.62 mm |
| 安裝類型 | Through-hole, PDIP-8 |
| Process Technology | Bipolar complementary processing |
LT1357CN8 7.62 mm 腳位配置指南
LT1357CN8(7.62 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LT1357CN8.
請參閱 資料表 以查看完整腳位配置。
典型應用
LT1357CN8 適用於 6 應用s: Fast Instrumentation Signal Conditioning, Pulse and Edge Signal Amplification, Active Filtering and Frequency Shaping, Current-to-Voltage Conversion, Video and Wideband Analog Buffering, Industrial Feedback Control Loops.
Fast Instrumentation Signal Conditioning
The LT1357CN8 fits precision analog front ends that must amplify sensor signals without sacrificing large-signal response. Its 25 MHz gain-bandwidth product supports moderate closed-loop gains, and the 600 V/us slew rate allows the amplifier to reproduce waveform edges that many general-purpose op amps would slow down. Place the device at the first gain stage, keep the input route short, and use the datasheet feedback and decoupling layouts to preserve stability. Confirm the input-common-mode range, offset voltage, and bias current against the sensor output before committing to the design.
推薦
Pulse and Edge Signal Amplification
The LT1357CN8 is useful where the information carried by pulse edges matters more than the steady-state level alone. Its 600 V/us slew rate provides fast large-signal transitions, while the 25 MHz gain-bandwidth product accommodates moderate closed-loop gain and higher-frequency content. Use it for pulse conditioning, clock-buffer amplification, and waveform cleanup when the output must follow the input without excessive edge rounding. Verify output swing, output-current capability, and stability at the intended gain, and provide local supply bypassing to keep the fast switching currents from disturbing adjacent circuitry.
推薦
Active Filtering and Frequency Shaping
The LT1357CN8 can implement active filters whose useful frequency range extends beyond general-purpose amplifiers. The 25 MHz gain-bandwidth product leaves bandwidth margin for moderate-gain filter sections, and the 600 V/us slew rate improves large-signal behavior in filters that process waveforms with significant amplitude. Place the amplifier and feedback components close together, use short ground returns, and avoid long parasitic loops around high-value resistors. Check the amplifier's open-loop response and noise behavior against the filter's passband and stopband targets.
推薦
Current-to-Voltage Conversion
The LT1357CN8 is appropriate for converting a small current-derived voltage into a larger analog signal with a wide bandwidth. Its high DC gain and 25 MHz gain-bandwidth product support transimpedance-style feedback arrangements, while the 600 V/us slew rate helps preserve rapidly changing current signals. Use a feedback resistor and compensation capacitor selected from the target transimpedance gain and bandwidth. Keep the input node physically small, protect the input from stray capacitance, and verify the input bias current because it creates an offset error in the converted voltage.
推薦
Video and Wideband Analog Buffering
The LT1357CN8 can buffer low-level video or wideband analog signals when conventional op amps introduce excessive edge-rate limitation. The 25 MHz bandwidth covers low-megahertz signal ranges, and the 600 V/us slew rate reduces large-signal distortion in square-wave and pulsed-video paths. Use the device as an inverting or non-inverting buffer with gain-setting resistors that keep the closed-loop bandwidth appropriate for the chosen gain. Account for output-swing limits and stable feedback layout, and evaluate group-delay and settling behavior if the application has waveform-integrity requirements.
推薦
Industrial Feedback Control Loops
The LT1357CN8 fits control and feedback loops that require rapid correction of an error signal. Its 600 V/us slew rate allows a substantial output change to occur quickly, and the 25 MHz gain-bandwidth product provides the loop bandwidth needed to follow faster system dynamics. Position the amplifier close to the feedback summing node, keep compensation components compact, and avoid routing the high-speed output through long traces. Confirm whether the loop requires a unity-gain-stable configuration or a specific compensation network before finalizing the gain and stability design.
推薦
推薦產品摘要
工程參考資料,適用於 LT1357CN8 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LT1357CN8#PBF |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 8-pin PDIP | 8-pin PDIP |
| Amplifier Type | Voltage Feedback | Voltage Feedback |
| Number of Circuits | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 25 MHz | 25 MHz |
| Slew Rate | 600 V/us | 600 V/us |
| Supply Current | 30 mA | 30 mA |
| Process Technology | Bipolar complementary processing | Bipolar complementary processing |
| Finish Designation | Standard ordering designation | Lead-free finish designation |
主要差異化特點
- High slew rate for a voltage-feedback amplifier (對比LT1357CN8#PBF)
- Single-amplifier PDIP implementation (對比LT1357CN8#PBF)
- Bipolar complementary processing (對比LT1357CN8#PBF)
設計說明
Route the non-inverting input, inverting input, feedback components, and output as a compact analog island because the LT1357's 25 MHz bandwidth and 600 V/us slew rate can amplify parasitic effects. Keep the input node compact, avoid running the feedback trace beside the input trace, and use a single ground reference without long return paths. Place supply-bypass capacitors at the pins specified in the manufacturer datasheet.
Do not select the amplifier from bandwidth alone. Check the output-voltage swing, output-current capability, input-common-mode range, offset voltage, bias current, and stability at the intended closed-loop gain. A 600 V/us slew rate cannot create additional output voltage range, and a high gain-bandwidth product does not guarantee acceptable noise or accuracy. Validate the complete operating point against the LT1357 datasheet before layout release.
For fast edges, treat power return and decoupling as part of the signal path. Keep the input and feedback connections away from high-current outputs and switching nodes, and evaluate the board with a scope for ringing, overshoot, and settling. The LT1357 combines voltage-feedback behavior with current-feedback-like slewing characteristics, so follow the manufacturer feedback-component recommendations rather than applying generic resistor values without stability checks.
合規資訊
The #PBF ordering suffix identifies a lead-free finish designation, but the product records do not explicitly state RoHS, REACH, halogen-free, or conflict-minerals status. The device is an analog amplifier and is not presented as an AEC-Q100-qualified automotive part.