MAX202IPWRE4 - 120 kbit/s Dual RS-232 Transceiver | Texas Instruments
MPN: MAX202IPWRE4 ✓ 啟用中MAX202IPWRE4 概覽
An RS-232 transceiver is an interface IC that converts logic-level signals into bipolar RS-232 line levels and converts received line signals back into logic-compatible levels. It belongs to the interface IC hierarchy, where transceivers combine drivers, receivers, and voltage-level conversion for reliable data links. The MAX202IPWRE4 implements this function with integrated charge pumps and external bypass capacitors, reducing the discrete component count required around a conventional RS-232 port.
The principal operating characteristics include a 5 V supply, a maximum data rate of 120 kbit/s, and ±15 kV human-body-model ESD protection on the serial-port connection pins, including ground. The device meets or exceeds TIA/EIA-232-F and ITU v.28 requirements. Two external 0.1 µF capacitors support the charge-pump circuit, while its 2/2 transceiver organization supports two transmit and two receive channels in one package.
Internally, the dual charge-pump circuit generates the positive and negative voltage levels required by RS-232 drivers. The receivers convert those bipolar levels into CMOS-compatible signals for the host controller. This integrated architecture is especially useful for legacy serial equipment, industrial control links, service interfaces, and embedded systems that retain an RS-232 port while using modern digital control logic.
Typical uses include point-to-point asynchronous serial links, instrument-control consoles, barcode and identification equipment, industrial diagnostics, and communication between a host UART and a DB9 or equivalent RS-232 connector. The dual-channel arrangement can serve two independent serial directions or paired command-and-status paths where channel count permits. System designers should also account for the cable, grounding, and connector requirements of the RS-232 standard.
Place each 0.1 µF charge-pump capacitor close to its designated IC pins and provide a low-impedance connection to the device ground. Keep the interface trace routing compact, and route the exposed RS-232 pins only toward the external connector because those nets carry high-voltage transients. A suitable serial connector and protection network should be placed close to the board edge.
This page consolidates the MAX202IPWRE4 electrical characteristics, package information, qualified comparison references, and practical PCB guidance into an engineer-focused guide. It also identifies where the available cross-reference records do not establish enough evidence to claim additional drop-in replacements.
直接替換替代品,適用於 MAX202IPWRE4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX202IPWRE4 (相同外形與佔位) — 差異在於 ESD Protection, Mounting Type, Product Type.
MAX202IPWR
✅ 直接替換📋 參考替代品(不在目錄中)
MAX202CPWR
✅ 直接替換✓ 有庫存
$0.9023 / 單位
查看資料表 →MAX202IPWRE4 規格
| Product Type | Dual RS-232 line driver/receiver |
| Transceiver Configuration | 2 transmit and 2 receive channels |
| 供應電壓 | 5 V |
| Maximum Data Rate | 120 kbit/s |
| ESD Protection | ±15 kV human-body model |
| RS-232 Standard Compliance | TIA/EIA-232-F and ITU v.28 |
| External Charge-Pump Capacitors | 0.1 µF |
| Package Type | 16-pin TSSOP |
| 安裝類型 | Surface mount |
| Terminal Count | 16 terminals |
| Temperature Grade | Industrial grade |
| 工作溫度範圍 | -40 °C to +85 °C |
| Internal Charge Pump | Dual charge-pump circuit |
| Driver Count | 2 line drivers |
| Receiver Count | 2 line receivers |
MAX202IPWRE4 16-pin tssop 腳位配置指南
MAX202IPWRE4(16-pin tssop 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX202IPWRE4.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX202IPWRE4 適用於 6 應用s: Industrial Equipment Serial Interface, Instrument Control Console, Point-to-Point Embedded Serial Link, Legacy Serial Equipment Adapter, Security and Access-Control Diagnostics, Data Acquisition and Control Module.
Industrial Equipment Serial Interface
The MAX202IPWRE4 fits industrial equipment that retains an RS-232 service or control port alongside a modern embedded controller. Its dual-driver and dual-receiver arrangement can connect two asynchronous UART channels without requiring separate RS-232 line-interface devices. The 5 V supply and 120 kbit/s operating rate suit moderate-speed command, status, and diagnostic traffic, while ±15 kV human-body-model ESD protection strengthens the external connector interface. Designers should use a robust industrial connector, controlled ground routing, and the two required 0.1 µF charge-pump capacitors. The principal trade-off is that RS-232 uses bipolar signaling and point-to-point links, so the cable and grounding arrangement remain part of the EMC and functional design.
推薦
Instrument Control Console
The MAX202IPWRE4 is appropriate for laboratory and test-instrument consoles that expose an RS-232 command interface to a host computer. The two receive channels can support separate status and response paths, while the two transmit channels can carry commands or requests where the host protocol requires two unidirectional links. At up to 120 kbit/s, the transceiver supports common low- and medium-speed serial-control protocols rather than high-throughput storage transfers. Its integrated charge pump reduces the external support circuitry needed for bipolar RS-232 levels. Place the MAX202 close to the connector, keep the external 0.1 µF capacitors short, and provide a low-impedance ground return to reduce susceptibility to ESD and ground-potential differences.
推薦
Point-to-Point Embedded Serial Link
The MAX202IPWRE4 works well as the physical-layer interface between an embedded UART and a remote RS-232 device when the link is point-to-point and limited to 120 kbit/s. It translates CMOS-compatible UART signaling into RS-232 levels in the transmit direction and performs the reverse conversion on the receive channels. This makes it useful in legacy access-control equipment, test fixtures, and service interfaces where the host processor lacks native RS-232 electrical drivers. The dual-channel structure can reduce component count when both directions require separate logic signals. Designers must observe the RS-232 voltage polarity, connector pinout, and cable limitations, and should verify that the UART baud rate and line timing remain appropriate for the connected peripheral.
推薦
Legacy Serial Equipment Adapter
The MAX202IPWRE4 supports adapters that preserve compatibility with older RS-232 equipment while exposing a modern processor or controller. Its two drivers and receivers permit more flexible channel allocation than a single-channel interface, and the 5 V operation allows integration into 5 V mixed-signal systems. The 120 kbit/s ceiling is suitable for configuration, command, and diagnostic traffic commonly found on legacy equipment. Use the manufacturer's pin-description table to implement the connector mapping, and ensure that unused receiver inputs are handled according to the device documentation. The key engineering consideration is that software compatibility does not guarantee electrical interchangeability: connector gender, signal names, grounding, and RS-232 level conventions must be checked independently.
推薦
Security and Access-Control Diagnostics
The MAX202IPWRE4 can interface diagnostic or programming ports in access-control and security equipment that use asynchronous RS-232 communication. The dual transmit and receive channels support command, response, or paired signal arrangements, while 120 kbit/s is more than adequate for typical configuration traffic. Its ±15 kV human-body-model ESD protection is especially relevant where an external serial connector may be touched or connected in uncontrolled environments. The protection rating does not eliminate the need for a good connector, chassis grounding, and normal board-level ESD precautions elsewhere. Keep the exposed driver and receiver traces away from sensitive digital and analog nets, and route the RS-232 connector interface directly toward the board edge for short transient paths.
推薦
Data Acquisition and Control Module
The MAX202IPWRE4 is suitable for data-acquisition modules that communicate with an external controller, programming fixture, or service computer over RS-232. The 120 kbit/s maximum accommodates periodic measurements, commands, and acknowledgment traffic, while the dual-channel arrangement can separate control and status traffic. Its integrated dual charge pump avoids a discrete negative-voltage generator, simplifying the power and layout design, but two external 0.1 µF capacitors remain mandatory. Ensure the transceiver ground connects to the circuit reference ground through a low-impedance path and assess whether galvanic isolation is required when the connected equipment may sit at a different ground potential. For longer cables or noisy environments, cable shielding and careful connector grounding can be as important as IC selection.
推薦
推薦產品摘要
工程參考資料,適用於 MAX202IPWRE4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX202IPWR | MAX202CPWR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Product Type | Dual RS-232 line driver/receiver | MAX202 dual RS-232 line driver/receiver | MAX202 dual RS-232 line driver/receiver |
| Transceiver Configuration | 2 transmit and 2 receive channels | 2 transmit and 2 receive channels | 2 transmit and 2 receive channels |
| Supply Voltage | 5 V | 5 V | 5 V |
| Maximum Data Rate | 120 kbit/s | 120 kbit/s | 120 kbit/s |
| ESD Protection | ±15 kV human-body model | ±15 kV human-body model | ±15 kV human-body model |
| External Charge-Pump Capacitors | 0.1 µF | 0.1 µF | 0.1 µF |
| RS-232 Compliance | TIA/EIA-232-F and ITU v.28 | TIA/EIA-232-F and ITU v.28 | TIA/EIA-232-F and ITU v.28 |
主要差異化特點
- Integrated dual-channel interface in a compact package (對比MAX202CPWR)
- Specified industrial-temperature operating range (對比MAX202CPWR)
- 120 kbit/s operation with ±15 kV ESD protection (對比MAX202IPWR)
設計說明
Place the two external 0.1 µF charge-pump capacitors immediately beside their designated MAX202 pins, using the shortest possible traces and an adjacent ground return. This is especially important because charge-pump behavior and ESD-event response can be affected by excessive loop area. Do not relocate the capacitors to the far side of the PCB, and do not substitute them for the values specified in the manufacturer MAX202 documentation.
Do not treat the MAX202IPWRE4 as a UART or a physical connector. The IC provides RS-232 electrical conversion only; baud-rate generation, framing, parity, flow control, and protocol handling remain the responsibility of the host controller. Also avoid connecting TTL or CMOS UART signals directly to the driver outputs, because the transceiver expects RS-232 bipolar levels on those external pins.
Route the external RS-232 pins toward the board edge and connector without passing beneath or between sensitive analog and digital nodes. Maintain a low-impedance ground connection between the transceiver and the interface connector, and use the connector shell or chassis-ground strategy appropriate to the enclosure. These measures reduce transient-current paths and improve immunity to ground-potential differences and externally applied ESD events.
The MAX202IPWRE4 and MAX202CPWR share the MAX202 family and a 16-pin TSSOP interface, but ordering suffixes can encode different temperature grades or delivery configurations. Before replacing one with another, compare the exact ordering tables, temperature ratings, ESD ratings, and package drawings. A matching footprint alone is not sufficient when a design must operate across a specific industrial temperature range.
合規資訊
TIA/EIA-232-F and ITU v.28 are interface standards documented for the MAX202 family, not product-level environmental compliance certifications. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified in the manufacturer references and therefore remain unknown.