MAX3243EUI+T - 3/5 RS-232 Transceiver, 250kbps | Maxim
MPN: MAX3243EUI+T ✓ 啟用中MAX3243EUI+T 概覽
An RS-232 transceiver is an interface IC that translates between logic-level signals and the bipolar voltage levels used by RS-232 links. The MAX3243 belongs to the RS-232 transceiver class within interface ICs, where it combines drivers, receivers, an on-board charge pump, and low-power shutdown control. This integration reduces the number of external components required for portable equipment, industrial controllers, and computer peripherals.
Key features include three RS-232 drivers, five RS-232 receivers, full-duplex operation, a 3 V to 5.5 V supply range, operation at up to 250 kbps, and ±15 kV ESD protection. AutoShutdown is particularly useful in battery-powered equipment because the device can reduce supply consumption when no valid receiver signal is present. A complementary always-active receiver supports continuous monitoring in designs that cannot tolerate shutdown of every receiver path.
The MAX3243 family combines an on-board power supply with RS-232 line-driver and receiver functions. Maxim's AutoShutdown circuitry detects whether a valid signal is present on the receiver inputs and shuts down the onboard supply and drivers when appropriate. The MAX3243EUI+T therefore supports both energy-efficient intermittent communication and always-active monitoring within one interface device.
Typical uses include battery-powered instruments, point-of-sale equipment, industrial data-acquisition systems, printers, portable computers, and external communications equipment. Its 28-pin TSSOP package is appropriate for compact industrial and embedded assemblies where three RS-232 outputs and five inputs are required. The interface is especially useful when a system must monitor several incoming lines while retaining the option to place unused drivers into a low-power state.
When designing around the MAX3243EUI+T, place the charge-pump capacitor and receiver and driver interface components according to the manufacturer's recommended layout. Confirm that every connected RS-232 line is protected against electrostatic discharge and that the selected cable does not exceed the voltage and grounding requirements of the RS-232 interface. Firmware should also account for AutoShutdown behavior when a remote system may disconnect without first sending a valid signal.
This product record combines the manufacturer specifications with package, application, comparison, and design guidance. It also separates exact catalog facts from electrical details that still require confirmation in the current Analog Devices or Maxim Integrated datasheet, helping engineers evaluate the MAX3243EUI+T for new RS-232 designs without confusing it with the faster MAX3243E or lower-speed MAX3243C variants.
直接替換替代品,適用於 MAX3243EUI+T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX3243EUI+T (相同外形與佔位) — 差異在於 Driver Count, Package, Product Type, Receiver Count.
此產品無可直接替換的替代品。
申請替代品MAX3243EUI+T 規格
| Product Type | 3-driver/5-receiver full-duplex RS-232 transceiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Driver Count | 3 drivers |
| Receiver Count | 5 receivers |
| ESD Protection | ±15 kV |
| AutoShutdown Supply Current | 1 µA |
| 封裝 | 28-pin TSSOP |
| 安裝類型 | Surface mount |
| Operating Voltage | 3 V to 5.5 V |
| Interface Standard | RS-232 |
| Duplex Mode | Full duplex |
| Low-Power Feature | AutoShutdown |
| Always-Active Monitoring | Complementary always-active receiver |
| 腳位數 | 28 pins |
| ESD Standard Qualification | ±15 kV IEC ESD protection |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
MAX3243EUI+T 28-pin tssop 腳位配置指南
MAX3243EUI+T(28-pin tssop 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX3243EUI+T.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX3243EUI+T 適用於 6 應用s: Battery-Powered Portable Instruments, Industrial Data-Acquisition Equipment, Point-of-Sale Terminal Peripherals, Printer and Legacy Peripheral Interfaces, Embedded Serial Communication Controllers, Telecommunications and Network Equipment.
Battery-Powered Portable Instruments
The MAX3243EUI+T fits portable instruments that exchange serial data through an RS-232 port while operating from a 3 V to 5.5 V battery-regulated rail. Its 250 kbps capability supports moderate-speed links, while AutoShutdown reduces supply current to 1 µA when the receiver inputs do not detect a valid signal. This is valuable for handheld test equipment and portable analyzers that spend substantial time idle. The design should account for wake-up timing and ensure that the system keeps enough state to recognize a returning remote device. The 28-pin TSSOP package also preserves board area compared with discrete driver, receiver, and charge-pump implementations.
推薦
Industrial Data-Acquisition Equipment
The MAX3243EUI+T is suitable for industrial data-acquisition units that need several incoming RS-232 signals but only three outgoing channels. Its five receivers allow controller status, alarm, and measurement-interface lines to be monitored simultaneously, while the complementary always-active receiver supports monitoring when the main AutoShutdown function is active. A maximum rate of 250 kbps is adequate for many legacy instrument-control protocols and short equipment links. Industrial implementations should still include robust grounding, cable transient protection, and verified logic thresholds because the ±15 kV ESD rating does not replace correct enclosure and cable design.
推薦
Point-of-Sale Terminal Peripherals
The MAX3243EUI+T can connect a point-of-sale controller or peripheral to legacy RS-232 equipment that requires multiple status inputs. Three driver outputs suit command or control channels, and five receivers can consolidate acknowledgement, readiness, and alarm signals into one interface IC. Operating from 3 V to 5.5 V supports modern mixed-voltage logic systems, and AutoShutdown reduces power when the peripheral is disconnected. For reliable deployment, the firmware should treat receiver state as potentially invalid during wake-up and should avoid assuming that a disconnected cable always presents a defined logic level.
推薦
Printer and Legacy Peripheral Interfaces
The MAX3243EUI+T is well suited to printer and legacy peripheral interfaces that combine bidirectional communication with additional status lines. The three-driver/5-receiver arrangement permits transmit, receive, paper-ready, fault, and busy signals to share one 28-pin TSSOP device. Its 250 kbps maximum rate is appropriate for many peripheral protocols that operate below that limit. The AutoShutdown function lowers consumption when a disconnected or inactive peripheral is detected, but the host software should include timeouts because line activity may not resume instantly. PCB layout should follow the manufacturer's recommended charge-pump and bypass-capacitor arrangement to minimize switching transients at the interface pins.
推薦
Embedded Serial Communication Controllers
The MAX3243EUI+T provides a practical RS-232 front end for embedded controllers whose UART operates at 3.3 V or 5 V. The interface accepts low-voltage logic and performs the level translation, charge-pump generation, and signal conditioning required by RS-232. With a 250 kbps ceiling and three drivers, it supports legacy control and diagnostic links without relying on an external RS-232 line-driver assembly. The always-active receiver path is valuable when an embedded system must detect an incoming condition even while other channels are shut down. Firmware should validate cable state and use deterministic timeouts around AutoShutdown wake-up behavior.
推薦
Telecommunications and Network Equipment
The MAX3243EUI+T can serve as a management or diagnostic interface in telecommunications and network equipment that retains RS-232 connectors for installation or service access. Three driver outputs and five receiver inputs support command, response, and hardware-status lines, while operation from 3 V to 5.5 V accommodates modern system rails. The 250 kbps limit is generally suitable for administrative terminal interfaces, whereas high-throughput traffic should use a faster standard. Equipment exposed to service ports should use controlled cable lengths, defined signal grounds, and appropriate surge protection in addition to the internal ±15 kV ESD capability.
推薦
推薦產品摘要
工程參考資料,適用於 MAX3243EUI+T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Package | 28-pin TSSOP |
| Brand | Maxim Integrated |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Driver Count | 3 drivers |
| Receiver Count | 5 receivers |
| ESD Protection | ±15 kV |
| AutoShutdown Supply Current | 1 µA |
| Duplex Mode | Full duplex |
| Low-Power Feature | AutoShutdown |
主要差異化特點
- Provides the required 250 kbps operating rate (對比MAX3243CUI+T)
- Avoids the faster-family functional mismatch (對比MAX3243EEUI+T)
- Combines three drivers, five receivers, and low-power shutdown (對比MAX3232ECDR)
設計說明
Route the MAX3243EUI+T charge-pump capacitor and bypass capacitors exactly as shown in the manufacturer's recommended layout, keeping the charge-pump loop compact. Place input and output interface paths away from clocks, switching regulators, and fast digital edges. Because the device is a 28-pin TSSOP, inspect the pad geometry and exposed thermal behavior against the final board assembly rather than relying only on nominal package dimensions.
Decouple the 3 V to 5.5 V supply close to the device and account for the charge-pump current when sizing the regulator and trace widths. The AutoShutdown function can reduce the transceiver's inactive supply current to 1 µA, but wake-up behavior and external circuitry determine the complete system quiescent current. Measure both shutdown and active current in the finished design instead of estimating from the transceiver specification alone.
Treat the RS-232 signal ground as part of the interface and connect it according to the equipment architecture rather than through long chassis paths. Maintain the recommended transceiver supply and bypass arrangement to minimize charge-pump noise at logic pins. The ±15 kV ESD rating improves robustness, but it does not protect against every industrial surge condition; external protection may still be required based on the installation environment.
Do not substitute MAX3243EEUI+T or MAX3243CUI+T solely because they use the same 28-pin TSSOP family. MAX3243EEUI+T is associated with the 500 kbps MAX3243E family, and MAX3243CUI+T is listed at 120 kbps, while the target MAX3243EUI+T supports up to 250 kbps. Also account for AutoShutdown in software by using timeouts and explicit line-state checks rather than treating a disconnected receiver as a valid communication session.
合規資訊
The MAX3243 product documentation identifies ±15 kV IEC ESD protection, but RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from current manufacturer product documentation or the project compliance system.