MAX368EPN+ - 8:1 Fault-Protected Mux | Analog Devices
MPN: MAX368EPN+ ✗ 停產MAX368EPN+ 概覽
An analog multiplexer is a semiconductor switch that connects one of several input terminals to a shared output. It belongs to the hierarchy of analog switch, multiplexer or demultiplexer, interface IC, and semiconductor. The MAX368EPN+ implements an 8:1 arrangement, allowing eight source signals to be presented to one downstream circuit without requiring a separate physical route for every signal.
The key stated characteristics include an 8:1 circuit configuration, 1.8 kOhm on-resistance, single-ended signal routing, and an 18-pin PDIP package. Its fault-protected analog multiplexer architecture and latch function are intended to support controlled signal selection in demanding equipment. Unlike a mechanically switched relay matrix, the MAX368EPN+ performs routing electronically through semiconductor switches.
The MAX368EPN+ is implemented as an integrated analog interface device rather than a power regulator or digital logic component. Its through-hole PDIP package supports conventional PCB insertion and socketed prototyping. The on-resistance specification is the principal quantified electrical characteristic identified for this exact MPN; detailed limits for supply voltage, channel leakage, bandwidth, switching time, and logic thresholds are not stated in the product records and should be taken from the manufacturer datasheet before design release.
Typical uses include industrial measurement and control systems, telecommunications equipment, and other analog signal paths where eight inputs must be routed to a common processing channel. The fault-protection and latch characteristics can be valuable in systems that need controlled behavior during input faults or transitions. Board-level design must still account for source impedance, settling behavior, injected noise, and the voltage range allowed for each switched node.
For a new PCB, use the 18-pin PDIP footprint and verify every signal and supply connection against the manufacturer pin-description table. Preserve adequate routing separation between high-impedance sources and the multiplexer output, provide suitable return paths, and validate the complete signal chain across temperature. Because this exact device is obsolete, a lifecycle-approved redesign should be selected before production commitment.
This page consolidates the exact MAX368EPN+ catalog identity, obsolete lifecycle status, package information, known multiplexing characteristics, practical application guidance, and constrained drop-in alternatives. It also separates confirmed facts from specifications that must be checked in the manufacturer datasheet, helping engineers make a more reliable sourcing and redesign decision.
直接替換替代品,適用於 MAX368EPN+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX368EPN+ (相同外形與佔位) — 差異在於 Mounting Type, Package, Temperature Grade.
MAX368CPN+
✅ 直接替換聯絡詢價
查看資料表 →MAX368EJN
✅ 直接替換📋 參考替代品(不在目錄中)
MAX368CPE+
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX368EPE+
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX368CJN+
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MAX368EPN+ 規格
| Multiplexer Configuration | 8:1 |
| Number of Circuits | 1 circuit |
| On-Resistance | 1.8 kOhm |
| Signal Configuration | Single-ended |
| Device Type | Fault-protected analog multiplexer with latch |
| 封裝 | 18-pin PDIP |
| Package Code | DIP |
| 安裝類型 | Through-hole |
| Number of Terminals | 18 terminals |
| Package Width | 0.300 inch (7.62 mm) |
| Temperature Grade | Industrial |
| 生命週期狀態 | Obsolete |
MAX368EPN+ 0.300 inch (7.62 mm) 腳位配置指南
MAX368EPN+(0.300 inch (7.62 mm) 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX368EPN+.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX368EPN+ 適用於 6 應用s: Industrial Measurement and Control, Telecommunications Signal Routing, Analog Sensor Interface, Test and Measurement Systems, Data Acquisition Modules, Legacy Control-System Service.
Industrial Measurement and Control
The MAX368EPN+ fits an industrial measurement system in which eight analog inputs share a common signal-conditioning path. Its 8:1 single-ended architecture reduces the number of physical connections required between field sensors and a controller or converter. The stated 1.8 kOhm on-resistance provides a known basis for evaluating source loading, while the fault-protected latch behavior supports controlled channel states. Because the component is obsolete, use it in an existing design or obtain explicit lifecycle approval before creating new production hardware.
推薦
Telecommunications Signal Routing
The MAX368EPN+ can route one of eight single-ended communications signals into a shared processing channel in telecommunications equipment. The through-hole 18-pin PDIP package is straightforward to assemble in legacy or service-oriented circuit boards, and the electronic multiplexing function avoids the mechanical complexity of a relay matrix. System designers should compare the 1.8 kOhm on-resistance against source impedance and bandwidth requirements. Control sequencing, fault recovery, and allowable node voltages must follow the manufacturer datasheet.
推薦
Analog Sensor Interface
The MAX368EPN+ is suitable for selecting among multiple low-bandwidth sensor outputs before amplification or conversion. Its 8:1 configuration gives an eight-channel front end a common analog path, while the 1.8 kOhm on-resistance must be included in the impedance budget of the selected sensor. The fault-protection and latch functions can help maintain a defined state during channel changes. Validate offset, leakage, settling time, and temperature behavior in the complete analog chain before production.
推薦
Test and Measurement Systems
The MAX368EPN+ can implement a compact eight-way analog test-point selector for legacy instrumentation. One multiplexer channel presents the selected DUT or fixture node to a shared meter, amplifier, or comparator. The single-ended architecture and 1.8 kOhm on-resistance are appropriate for many low-frequency measurement paths, but high-impedance sources may require additional buffering. Confirm leakage, switching transients, and settle time against the required measurement accuracy.
推薦
Data Acquisition Modules
An eight-input data-acquisition module can use the MAX368EPN+ to select one analog source for a shared converter or amplifier. This arrangement is most appropriate where channels have similar impedance and bandwidth and where the 8:1 topology provides a practical reduction in routing complexity. The 1.8 kOhm switch resistance should be included in gain and source-loading calculations. The obsolete lifecycle status requires an exception for new designs or a planned migration to a supported equivalent.
推薦
Legacy Control-System Service
The MAX368EPN+ is relevant to maintenance and repair of legacy industrial control equipment that already uses an 18-pin PDIP analog multiplexer. Its through-hole package supports board-level replacement when lead spacing, pin functions, and electrical ratings match the original assembly. Service engineers should preserve the original grade and latch configuration to avoid subtle control differences. Request traceable inventory through the quote form and inspect date codes, soldering condition, and continuity before installation.
推薦
推薦產品摘要
工程參考資料,適用於 MAX368EPN+ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX368CPN+ | MAX368EJN | MAX368CPE+ | MAX368EPE+ | MAX368CJN+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 18-pin PDIP | 18-pin PDIP | 18-pin PDIP | 18-pin PDIP | 18-pin PDIP | 18-pin PDIP |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
主要差異化特點
- Industrial-grade identity with a confirmed 1.8 kOhm on-resistance (對比MAX368CPN+)
- Same-package 8:1 architecture for legacy board replacement (對比MAX368EJN)
- Fault-protected multiplexing with an integrated latch function (對比MAX368CPE+)
設計說明
Do not treat physical package equality as proof that MAX368 suffix variants are electrically interchangeable. Verify the ordering-suffix temperature grade, supply limits, logic thresholds, latch behavior, channel characteristics, and absolute maximum ratings against the manufacturer datasheet. MAX368CPN+ and MAX368EJN appear in the cross-reference material with the same 18-pin PDIP format, but the comparison record states that some electrical characteristics differ.
Include the stated 1.8 kOhm on-resistance when calculating source loading, especially for high-impedance sensors. The effective source impedance can degrade channel-to-channel amplitude accuracy and offset accuracy when several input networks are multiplexed. Use the manufacturer datasheet to obtain leakage, switching time, bandwidth, and off-impedance data, then simulate settling and crosstalk across the intended temperature range.
Route the eight inputs, common output, control signals, and supply connections according to the 18-pin PDIP pin-description table. Keep sensitive analog traces away from digital control and return-current paths, provide a direct ground reference near the device, and avoid long stubs around high-impedance inputs. Because the device is obsolete, preserve the original footprint and routing in repair and redesign boards to simplify future substitution.
Decouple the supply pins with the capacitance and placement specified in the Maxim Integrated datasheet. Keep supply return current separate from sensitive analog returns where practical, and confirm that startup, fault recovery, and latch transitions do not drive an input beyond its permitted voltage range. External input clamping may still be required because the integrated fault-protection function does not replace application-specific surge protection.
合規資訊
The product record does not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is recorded as not applicable because this is an industrial analog interface IC rather than an automotive-qualified device.