MAX368EPN+ - 8:1 Fault-Protected Mux | Analog Devices
MPN: MAX368EPN+ ✗ Akhir HayatMAX368EPN+ Ringkasan
An analog multiplexer is a semiconductor switch that connects one of several input terminals to a shared output. It belongs to the hierarchy of analog switch, multiplexer or demultiplexer, interface IC, and semiconductor. The MAX368EPN+ implements an 8:1 arrangement, allowing eight source signals to be presented to one downstream circuit without requiring a separate physical route for every signal.
The key stated characteristics include an 8:1 circuit configuration, 1.8 kOhm on-resistance, single-ended signal routing, and an 18-pin PDIP package. Its fault-protected analog multiplexer architecture and latch function are intended to support controlled signal selection in demanding equipment. Unlike a mechanically switched relay matrix, the MAX368EPN+ performs routing electronically through semiconductor switches.
The MAX368EPN+ is implemented as an integrated analog interface device rather than a power regulator or digital logic component. Its through-hole PDIP package supports conventional PCB insertion and socketed prototyping. The on-resistance specification is the principal quantified electrical characteristic identified for this exact MPN; detailed limits for supply voltage, channel leakage, bandwidth, switching time, and logic thresholds are not stated in the product records and should be taken from the manufacturer datasheet before design release.
Typical uses include industrial measurement and control systems, telecommunications equipment, and other analog signal paths where eight inputs must be routed to a common processing channel. The fault-protection and latch characteristics can be valuable in systems that need controlled behavior during input faults or transitions. Board-level design must still account for source impedance, settling behavior, injected noise, and the voltage range allowed for each switched node.
For a new PCB, use the 18-pin PDIP footprint and verify every signal and supply connection against the manufacturer pin-description table. Preserve adequate routing separation between high-impedance sources and the multiplexer output, provide suitable return paths, and validate the complete signal chain across temperature. Because this exact device is obsolete, a lifecycle-approved redesign should be selected before production commitment.
This page consolidates the exact MAX368EPN+ catalog identity, obsolete lifecycle status, package information, known multiplexing characteristics, practical application guidance, and constrained drop-in alternatives. It also separates confirmed facts from specifications that must be checked in the manufacturer datasheet, helping engineers make a more reliable sourcing and redesign decision.
Pilihan pengganti yang segera untuk MAX368EPN+ — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera MAX368EPN+ (sama faktor bentuk dan kaki) — berbeza dalam Mounting Type, Package, Temperature Grade.
MAX368CPN+
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →MAX368EJN
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MAX368CPE+
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
MAX368EPE+
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
MAX368CJN+
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
MAX368EPN+ Spesifikasi
| Multiplexer Configuration | 8:1 |
| Number of Circuits | 1 circuit |
| On-Resistance | 1.8 kOhm |
| Signal Configuration | Single-ended |
| Device Type | Fault-protected analog multiplexer with latch |
| Kemasan | 18-pin PDIP |
| Package Code | DIP |
| Jenis Pemasangan | Through-hole |
| Number of Terminals | 18 terminals |
| Package Width | 0.300 inch (7.62 mm) |
| Temperature Grade | Industrial |
| Status Lingkungan Hidup | Obsolete |
Panduan Konfigurasi Pin MAX368EPN+ 0.300 inch (7.62 mm)
Konfigurasi pin untuk MAX368EPN+ (0.300 inch (7.62 mm) pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk MAX368EPN+.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
MAX368EPN+ patut untuk 6 aplikasis: Industrial Measurement and Control, Telecommunications Signal Routing, Analog Sensor Interface, Test and Measurement Systems, Data Acquisition Modules, Legacy Control-System Service.
Industrial Measurement and Control
The MAX368EPN+ fits an industrial measurement system in which eight analog inputs share a common signal-conditioning path. Its 8:1 single-ended architecture reduces the number of physical connections required between field sensors and a controller or converter. The stated 1.8 kOhm on-resistance provides a known basis for evaluating source loading, while the fault-protected latch behavior supports controlled channel states. Because the component is obsolete, use it in an existing design or obtain explicit lifecycle approval before creating new production hardware.
Disebarkan
Telecommunications Signal Routing
The MAX368EPN+ can route one of eight single-ended communications signals into a shared processing channel in telecommunications equipment. The through-hole 18-pin PDIP package is straightforward to assemble in legacy or service-oriented circuit boards, and the electronic multiplexing function avoids the mechanical complexity of a relay matrix. System designers should compare the 1.8 kOhm on-resistance against source impedance and bandwidth requirements. Control sequencing, fault recovery, and allowable node voltages must follow the manufacturer datasheet.
Disebarkan
Analog Sensor Interface
The MAX368EPN+ is suitable for selecting among multiple low-bandwidth sensor outputs before amplification or conversion. Its 8:1 configuration gives an eight-channel front end a common analog path, while the 1.8 kOhm on-resistance must be included in the impedance budget of the selected sensor. The fault-protection and latch functions can help maintain a defined state during channel changes. Validate offset, leakage, settling time, and temperature behavior in the complete analog chain before production.
Disebarkan
Test and Measurement Systems
The MAX368EPN+ can implement a compact eight-way analog test-point selector for legacy instrumentation. One multiplexer channel presents the selected DUT or fixture node to a shared meter, amplifier, or comparator. The single-ended architecture and 1.8 kOhm on-resistance are appropriate for many low-frequency measurement paths, but high-impedance sources may require additional buffering. Confirm leakage, switching transients, and settle time against the required measurement accuracy.
Disebarkan
Data Acquisition Modules
An eight-input data-acquisition module can use the MAX368EPN+ to select one analog source for a shared converter or amplifier. This arrangement is most appropriate where channels have similar impedance and bandwidth and where the 8:1 topology provides a practical reduction in routing complexity. The 1.8 kOhm switch resistance should be included in gain and source-loading calculations. The obsolete lifecycle status requires an exception for new designs or a planned migration to a supported equivalent.
Disebarkan
Legacy Control-System Service
The MAX368EPN+ is relevant to maintenance and repair of legacy industrial control equipment that already uses an 18-pin PDIP analog multiplexer. Its through-hole package supports board-level replacement when lead spacing, pin functions, and electrical ratings match the original assembly. Service engineers should preserve the original grade and latch configuration to avoid subtle control differences. Request traceable inventory through the quote form and inspect date codes, soldering condition, and continuity before installation.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk MAX368EPN+ — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | MAX368CPN+ | MAX368EJN | MAX368CPE+ | MAX368EPE+ | MAX368CJN+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 18-pin PDIP | 18-pin PDIP | 18-pin PDIP | 18-pin PDIP | 18-pin PDIP | 18-pin PDIP |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
Penyeberangsung Jelas
- Industrial-grade identity with a confirmed 1.8 kOhm on-resistance (vsMAX368CPN+)
- Same-package 8:1 architecture for legacy board replacement (vsMAX368EJN)
- Fault-protected multiplexing with an integrated latch function (vsMAX368CPE+)
Catatan Desain
Do not treat physical package equality as proof that MAX368 suffix variants are electrically interchangeable. Verify the ordering-suffix temperature grade, supply limits, logic thresholds, latch behavior, channel characteristics, and absolute maximum ratings against the manufacturer datasheet. MAX368CPN+ and MAX368EJN appear in the cross-reference material with the same 18-pin PDIP format, but the comparison record states that some electrical characteristics differ.
Include the stated 1.8 kOhm on-resistance when calculating source loading, especially for high-impedance sensors. The effective source impedance can degrade channel-to-channel amplitude accuracy and offset accuracy when several input networks are multiplexed. Use the manufacturer datasheet to obtain leakage, switching time, bandwidth, and off-impedance data, then simulate settling and crosstalk across the intended temperature range.
Route the eight inputs, common output, control signals, and supply connections according to the 18-pin PDIP pin-description table. Keep sensitive analog traces away from digital control and return-current paths, provide a direct ground reference near the device, and avoid long stubs around high-impedance inputs. Because the device is obsolete, preserve the original footprint and routing in repair and redesign boards to simplify future substitution.
Decouple the supply pins with the capacitance and placement specified in the Maxim Integrated datasheet. Keep supply return current separate from sensitive analog returns where practical, and confirm that startup, fault recovery, and latch transitions do not drive an input beyond its permitted voltage range. External input clamping may still be required because the integrated fault-protection function does not replace application-specific surge protection.
Maklumat Kesediaan
The product record does not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is recorded as not applicable because this is an industrial analog interface IC rather than an automotive-qualified device.