MC14503BF - Hex 3-State Non-Inverting Buffer | onsemi
MPN: MC14503BF ✗ 停產MC14503BF 概覽
A 3-state buffer is a digital interface component that can present a valid logic level, actively drive a bus, or electrically release the bus with a high-impedance output. The three-state function distinguishes it from a conventional buffer, which continuously drives its output. By placing several drivers in parallel, a system can reduce contention when only one device is active. The hex organization provides six non-inverting channels in one package.
The MC14503BF supports common-bus architectures where source and sink capability must accommodate driven logic levels. Its 150 ns propagation delay provides a defined timing relationship between an input transition and the corresponding output transition. The 50 pF load-capability figure identifies a useful bus-loading condition when evaluating interconnect behavior. Two disable inputs add local bus-segment control without requiring individual output gating at the source logic.
The MC14503BF is a bipolar CMOS-family logic device, with the MC14503B family identified by onsemi as a hex non-inverting, 3-state buffer. The two disable controls divide the six buffers into separately controlled groups: Disable A controls buffers 1 through 4, while Disable B controls buffers 5 through 6. This arrangement permits a compact implementation of segmented shared buses, bidirectional-looking bus translators built from unidirectional channels, and systems that require a driver to relinquish a line during another device's transfer cycle.
Typical uses include microprocessor and microcontroller bus isolation, memory-module data buses, peripheral port expansion, test-interface routing, and industrial control systems with shared parallel data paths. The device is particularly relevant when one group of four channels must disengage together while another group of two channels remains active. The package also provides through-hole mechanical compatibility with conventional 16-pin logic-board layouts.
For reliable operation, design the disable signals so that no two devices actively drive the same shared node simultaneously. Account for output propagation delay when establishing bus ownership timing, and keep signal routing short enough to limit capacitive loading. Because the device includes a high-impedance state, the disable logic must actively establish every required output state rather than relying on floating control inputs.
This product page combines the functional description, technical attributes, sourcing information, interface use cases, and design guidance needed to evaluate the MC14503BF. It also organizes drop-in alternatives and engineering trade-offs so designers can determine whether the original part remains the best fit before modifying a PCB or changing the bus architecture.
直接替換替代品,適用於 MC14503BF — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MC14503BE
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MC14503BF 最大額定值與電氣特性
| Logic Type | Hex non-inverting 3-state buffer |
| Number of Channels | 6 channels |
| 輸出數量 | 6 outputs |
| Output State | 3-state, including high-impedance |
| Propagation Delay | 150 ns |
| Nominal Supply Voltage | 5 V |
| Load Capacitance | 50 pF |
| Output Current Capability | High current source and sink capability |
| Disable Controls | 2 controls |
| Disable A Control | Controls outputs of buffers 1 through 4 |
| Disable B Control | Controls outputs of buffers 5 through 6 |
| 工作溫度 | -55 °C to +125 °C |
| 封裝 | 16-pin PDIP |
| 安裝類型 | Through-hole |
| Product Type | Buffer/Driver/Transceiver |
MC14503BF 16-pin pdip 腳位配置指南
MC14503BF(16-pin pdip 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: MC14503BF.
請參閱 資料表 以查看完整腳位配置。
典型應用
MC14503BF 適用於 6 應用s: Shared Microprocessor Data Bus, Peripheral Port Isolation, Industrial Control Backplane, Memory Module Data Routing, Legacy Test and Measurement Interface, Multichannel Digital Control Interface.
Shared Microprocessor Data Bus
The MC14503BF fits a shared parallel data bus in which several peripheral devices may connect to the same processor-side signals. Its six non-inverting 3-state channels allow enabled devices to drive the bus while disabled devices release it at high impedance, reducing contention risk. The 150 ns propagation delay and 50 pF load-capability figure provide concrete timing and loading targets. Disable A can disengage four channels together, while Disable B controls the remaining two, enabling segmented ownership. Designers should verify output contention, voltage-level compatibility, and timing margins at the target bus speed.
推薦
Peripheral Port Isolation
The MC14503BF can isolate a group of peripheral port lines from a common system bus by placing the corresponding channels in the high-impedance state. This is useful when a memory card, removable module, or expansion interface must be electrically disconnected while other logic remains active. The grouped disable architecture lets four outputs disengage together and two additional outputs form a separate segment. The device's 5 V nominal operation and non-inverting logic preserve signal polarity, while the 16-pin PDIP format supports through-hole boards and repair-oriented legacy designs.
推薦
Industrial Control Backplane
The MC14503BF is appropriate for a segmented industrial control backplane where controller cards and interface modules share parallel command or status lines. Three-state outputs allow an inactive card to release the bus, and the separate disable groups provide coarse control over four-channel and two-channel sections. Its operating temperature range of -55 °C to +125 °C supports demanding environmental designs when the complete assembly meets its own qualification requirements. Engineers should evaluate bus rise time, connector loading, grounding, and contention timing before finalizing the backplane topology.
推薦
Memory Module Data Routing
The MC14503BF can provide buffered, selectable routing for legacy memory-module data lines where the system must isolate devices during a bus transfer. Six non-inverting channels preserve data polarity, while Disable A and Disable B let the controller release two differently sized channel groups. The 150 ns delay must be included in address, chip-select, and data-valid timing, particularly around memory-access transitions. Its high-current source and sink capability is useful for driving board-level interconnects, while the 50 pF load figure provides a defined benchmark for initial signal-integrity assessment.
推薦
Legacy Test and Measurement Interface
The MC14503BF fits legacy test and measurement equipment that routes several parallel measurement-control signals to a shared connector or backplane. The 3-state outputs permit the active instrument section to drive the lines while disconnected sections remain high impedance, avoiding interference between modules. Non-inverting channels make this useful where signal polarity must remain unchanged, and two grouped disable inputs simplify board-level bus segmentation. Because this is an older through-hole logic device, verify connector pin assignments, cable capacitance, grounding, and timing before integrating it into a new measurement platform.
推薦
Multichannel Digital Control Interface
The MC14503BF can buffer several digital control lines entering a legacy controller card when the host side uses a shared multidrop connection. Disable A provides simultaneous release of four channels, while Disable B handles two additional channels, allowing the card to disconnect predictably. The 5 V nominal supply and non-inverting 3-state outputs suit conventional TTL-level logic when operating limits and levels are verified. Layout should minimize stub branches, provide a continuous ground reference, and ensure that no disabled output is relied upon as a valid data state.
推薦
推薦產品摘要
工程參考資料,適用於 MC14503BF — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Brand | onsemi |
| Package | 16-pin PDIP |
| Logic Type | Hex non-inverting 3-state buffer |
| Number of Channels | 6 channels |
| Nominal Supply Voltage | 5 V |
| Propagation Delay | 150 ns |
| Load Capacitance | 50 pF |
| Disable Controls | 2 grouped disable inputs |
| Operating Temperature | -55 °C to +125 °C |
| Output Capability | High current source and sink capability |
主要差異化特點
- Grouped three-state output control (對比Generic single-enable hex bus buffer)
- Non-inverting signal path (對比Inverting hex transceiver)
- Through-hole legacy PCB compatibility (對比Surface-mount-only bus buffer)
設計說明
Ensure that only one enabled device drives any shared node. The MC14503BF uses high impedance to relinquish a bus, but two simultaneously active outputs can still contend if they attempt opposing logic levels. Define ownership and disable timing so that one driver fully releases the line before the next driver enables. Include the 150 ns propagation delay and the intended disable settling interval when sequencing bus transfers.
Keep connections to the 16-pin PDIP short and provide a continuous ground path near the device. Avoid long stub branches that add capacitance beyond the stated 50 pF load condition. When the outputs drive a connector or backplane, test the assembled interconnect because connector and PCB-trace capacitance contributes to rise time and bus settling. Maintain consistent return paths between the buffer and the devices connected to its shared lines.
Decouple the 5 V supply locally and route the return current without sharing narrow paths with high-current output loads. Although the outputs are designed with high-current source and sink capability, package and board limitations still apply to simultaneous transitions. Place the decoupling capacitor close to the supply and ground pins and check the supply voltage at the device during worst-case bus activity.
合規資訊
The MC14503BF is a legacy integrated circuit and is not presented as an AEC-Q100 automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed for the exact manufacturing lot and supply condition.