MC14503BF - Hex 3-State Non-Inverting Buffer | onsemi
料号: MC14503BF ✗ 停产MC14503BF 概述
A 3-state buffer is a digital interface component that can present a valid logic level, actively drive a bus, or electrically release the bus with a high-impedance output. The three-state function distinguishes it from a conventional buffer, which continuously drives its output. By placing several drivers in parallel, a system can reduce contention when only one device is active. The hex organization provides six non-inverting channels in one package.
The MC14503BF supports common-bus architectures where source and sink capability must accommodate driven logic levels. Its 150 ns propagation delay provides a defined timing relationship between an input transition and the corresponding output transition. The 50 pF load-capability figure identifies a useful bus-loading condition when evaluating interconnect behavior. Two disable inputs add local bus-segment control without requiring individual output gating at the source logic.
The MC14503BF is a bipolar CMOS-family logic device, with the MC14503B family identified by onsemi as a hex non-inverting, 3-state buffer. The two disable controls divide the six buffers into separately controlled groups: Disable A controls buffers 1 through 4, while Disable B controls buffers 5 through 6. This arrangement permits a compact implementation of segmented shared buses, bidirectional-looking bus translators built from unidirectional channels, and systems that require a driver to relinquish a line during another device's transfer cycle.
Typical uses include microprocessor and microcontroller bus isolation, memory-module data buses, peripheral port expansion, test-interface routing, and industrial control systems with shared parallel data paths. The device is particularly relevant when one group of four channels must disengage together while another group of two channels remains active. The package also provides through-hole mechanical compatibility with conventional 16-pin logic-board layouts.
For reliable operation, design the disable signals so that no two devices actively drive the same shared node simultaneously. Account for output propagation delay when establishing bus ownership timing, and keep signal routing short enough to limit capacitive loading. Because the device includes a high-impedance state, the disable logic must actively establish every required output state rather than relying on floating control inputs.
This product page combines the functional description, technical attributes, sourcing information, interface use cases, and design guidance needed to evaluate the MC14503BF. It also organizes drop-in alternatives and engineering trade-offs so designers can determine whether the original part remains the best fit before modifying a PCB or changing the bus architecture.
直接替换替代料: MC14503BF ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MC14503BE
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MC14503BF 最大额定值与电气特性
| Logic Type | Hex non-inverting 3-state buffer |
| Number of Channels | 6 channels |
| 输出数量 | 6 outputs |
| Output State | 3-state, including high-impedance |
| Propagation Delay | 150 ns |
| Nominal Supply Voltage | 5 V |
| Load Capacitance | 50 pF |
| Output Current Capability | High current source and sink capability |
| Disable Controls | 2 controls |
| Disable A Control | Controls outputs of buffers 1 through 4 |
| Disable B Control | Controls outputs of buffers 5 through 6 |
| 工作温度 | -55 °C to +125 °C |
| 封装 | 16-pin PDIP |
| 安装类型 | Through-hole |
| Product Type | Buffer/Driver/Transceiver |
MC14503BF 16-pin pdip 引脚配置指南
MC14503BF(16-pin pdip 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: MC14503BF.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MC14503BF 适用于 6 应用s: Shared Microprocessor Data Bus, Peripheral Port Isolation, Industrial Control Backplane, Memory Module Data Routing, Legacy Test and Measurement Interface, Multichannel Digital Control Interface.
Shared Microprocessor Data Bus
The MC14503BF fits a shared parallel data bus in which several peripheral devices may connect to the same processor-side signals. Its six non-inverting 3-state channels allow enabled devices to drive the bus while disabled devices release it at high impedance, reducing contention risk. The 150 ns propagation delay and 50 pF load-capability figure provide concrete timing and loading targets. Disable A can disengage four channels together, while Disable B controls the remaining two, enabling segmented ownership. Designers should verify output contention, voltage-level compatibility, and timing margins at the target bus speed.
推荐
Peripheral Port Isolation
The MC14503BF can isolate a group of peripheral port lines from a common system bus by placing the corresponding channels in the high-impedance state. This is useful when a memory card, removable module, or expansion interface must be electrically disconnected while other logic remains active. The grouped disable architecture lets four outputs disengage together and two additional outputs form a separate segment. The device's 5 V nominal operation and non-inverting logic preserve signal polarity, while the 16-pin PDIP format supports through-hole boards and repair-oriented legacy designs.
推荐
Industrial Control Backplane
The MC14503BF is appropriate for a segmented industrial control backplane where controller cards and interface modules share parallel command or status lines. Three-state outputs allow an inactive card to release the bus, and the separate disable groups provide coarse control over four-channel and two-channel sections. Its operating temperature range of -55 °C to +125 °C supports demanding environmental designs when the complete assembly meets its own qualification requirements. Engineers should evaluate bus rise time, connector loading, grounding, and contention timing before finalizing the backplane topology.
推荐
Memory Module Data Routing
The MC14503BF can provide buffered, selectable routing for legacy memory-module data lines where the system must isolate devices during a bus transfer. Six non-inverting channels preserve data polarity, while Disable A and Disable B let the controller release two differently sized channel groups. The 150 ns delay must be included in address, chip-select, and data-valid timing, particularly around memory-access transitions. Its high-current source and sink capability is useful for driving board-level interconnects, while the 50 pF load figure provides a defined benchmark for initial signal-integrity assessment.
推荐
Legacy Test and Measurement Interface
The MC14503BF fits legacy test and measurement equipment that routes several parallel measurement-control signals to a shared connector or backplane. The 3-state outputs permit the active instrument section to drive the lines while disconnected sections remain high impedance, avoiding interference between modules. Non-inverting channels make this useful where signal polarity must remain unchanged, and two grouped disable inputs simplify board-level bus segmentation. Because this is an older through-hole logic device, verify connector pin assignments, cable capacitance, grounding, and timing before integrating it into a new measurement platform.
推荐
Multichannel Digital Control Interface
The MC14503BF can buffer several digital control lines entering a legacy controller card when the host side uses a shared multidrop connection. Disable A provides simultaneous release of four channels, while Disable B handles two additional channels, allowing the card to disconnect predictably. The 5 V nominal supply and non-inverting 3-state outputs suit conventional TTL-level logic when operating limits and levels are verified. Layout should minimize stub branches, provide a continuous ground reference, and ensure that no disabled output is relied upon as a valid data state.
推荐
推荐产品汇总
工程参考数据: MC14503BF ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Brand | onsemi |
| Package | 16-pin PDIP |
| Logic Type | Hex non-inverting 3-state buffer |
| Number of Channels | 6 channels |
| Nominal Supply Voltage | 5 V |
| Propagation Delay | 150 ns |
| Load Capacitance | 50 pF |
| Disable Controls | 2 grouped disable inputs |
| Operating Temperature | -55 °C to +125 °C |
| Output Capability | High current source and sink capability |
关键差异点
- Grouped three-state output control (对比 Generic single-enable hex bus buffer)
- Non-inverting signal path (对比 Inverting hex transceiver)
- Through-hole legacy PCB compatibility (对比 Surface-mount-only bus buffer)
设计说明
Ensure that only one enabled device drives any shared node. The MC14503BF uses high impedance to relinquish a bus, but two simultaneously active outputs can still contend if they attempt opposing logic levels. Define ownership and disable timing so that one driver fully releases the line before the next driver enables. Include the 150 ns propagation delay and the intended disable settling interval when sequencing bus transfers.
Keep connections to the 16-pin PDIP short and provide a continuous ground path near the device. Avoid long stub branches that add capacitance beyond the stated 50 pF load condition. When the outputs drive a connector or backplane, test the assembled interconnect because connector and PCB-trace capacitance contributes to rise time and bus settling. Maintain consistent return paths between the buffer and the devices connected to its shared lines.
Decouple the 5 V supply locally and route the return current without sharing narrow paths with high-current output loads. Although the outputs are designed with high-current source and sink capability, package and board limitations still apply to simultaneous transitions. Place the decoupling capacitor close to the supply and ground pins and check the supply voltage at the device during worst-case bus activity.
合规信息
The MC14503BF is a legacy integrated circuit and is not presented as an AEC-Q100 automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed for the exact manufacturing lot and supply condition.