onsemi

MC14503BF - Hex 3-State Non-Inverting Buffer | onsemi

부품 번호: MC14503BF ✗ 단종
5 V Vdss High current source and sink capability Id 16-pin PDIP Package
MOQ: 1 |

MC14503BF 개요

onsemi MC14503BF is a hex non-inverting buffer with six 3-state outputs, a 5 V nominal operating voltage, 150 ns propagation delay, and a 16-lead PDIP package. The device provides high-current source and sink capability, making it suitable for common-bus applications where multiple logic devices must share an interconnect. Two independent disable controls allow buffers 1 through 4 and buffers 5 through 6 to be placed in the high-impedance state independently.

A 3-state buffer is a digital interface component that can present a valid logic level, actively drive a bus, or electrically release the bus with a high-impedance output. The three-state function distinguishes it from a conventional buffer, which continuously drives its output. By placing several drivers in parallel, a system can reduce contention when only one device is active. The hex organization provides six non-inverting channels in one package.

The MC14503BF supports common-bus architectures where source and sink capability must accommodate driven logic levels. Its 150 ns propagation delay provides a defined timing relationship between an input transition and the corresponding output transition. The 50 pF load-capability figure identifies a useful bus-loading condition when evaluating interconnect behavior. Two disable inputs add local bus-segment control without requiring individual output gating at the source logic.

The MC14503BF is a bipolar CMOS-family logic device, with the MC14503B family identified by onsemi as a hex non-inverting, 3-state buffer. The two disable controls divide the six buffers into separately controlled groups: Disable A controls buffers 1 through 4, while Disable B controls buffers 5 through 6. This arrangement permits a compact implementation of segmented shared buses, bidirectional-looking bus translators built from unidirectional channels, and systems that require a driver to relinquish a line during another device's transfer cycle.

Typical uses include microprocessor and microcontroller bus isolation, memory-module data buses, peripheral port expansion, test-interface routing, and industrial control systems with shared parallel data paths. The device is particularly relevant when one group of four channels must disengage together while another group of two channels remains active. The package also provides through-hole mechanical compatibility with conventional 16-pin logic-board layouts.

For reliable operation, design the disable signals so that no two devices actively drive the same shared node simultaneously. Account for output propagation delay when establishing bus ownership timing, and keep signal routing short enough to limit capacitive loading. Because the device includes a high-impedance state, the disable logic must actively establish every required output state rather than relying on floating control inputs.

This product page combines the functional description, technical attributes, sourcing information, interface use cases, and design guidance needed to evaluate the MC14503BF. It also organizes drop-in alternatives and engineering trade-offs so designers can determine whether the original part remains the best fit before modifying a PCB or changing the bus architecture.

드롭인 대체품: MC14503BF — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

MC14503BE

✅ 드롭인 ⚠️ 사양 미검증
📦 PDIP-16
Same MC14503B six-channel non-inverting three-state architecture and 16-pin PDIP pinout; ordering-code attributes differ, with no change to the identified 150 ns propagation delay or 50 pF rated load

📋 참조 대체품 (카탈로그에 없음)

MC14503BF 최대 정격 & 전기적 특성

Logic Type Hex non-inverting 3-state buffer
Number of Channels 6 channels
출력 수 6 outputs
Output State 3-state, including high-impedance
Propagation Delay 150 ns
Nominal Supply Voltage 5 V
Load Capacitance 50 pF
Output Current Capability High current source and sink capability
Disable Controls 2 controls
Disable A Control Controls outputs of buffers 1 through 4
Disable B Control Controls outputs of buffers 5 through 6
동작 온도 -55 °C to +125 °C
패키지 16-pin PDIP
실장 유형 Through-hole
Product Type Buffer/Driver/Transceiver

MC14503BF 16-pin pdip 핀 구성 가이드

MC14503BF(16-pin pdip 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.

MC14503BF의 16-pin pdip 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: MC14503BF.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

MC14503BF 적합 용도: 6 애플리케이션s: Shared Microprocessor Data Bus, Peripheral Port Isolation, Industrial Control Backplane, Memory Module Data Routing, Legacy Test and Measurement Interface, Multichannel Digital Control Interface.

🖥️

Shared Microprocessor Data Bus

The MC14503BF fits a shared parallel data bus in which several peripheral devices may connect to the same processor-side signals. Its six non-inverting 3-state channels allow enabled devices to drive the bus while disabled devices release it at high impedance, reducing contention risk. The 150 ns propagation delay and 50 pF load-capability figure provide concrete timing and loading targets. Disable A can disengage four channels together, while Disable B controls the remaining two, enabling segmented ownership. Designers should verify output contention, voltage-level compatibility, and timing margins at the target bus speed.

🔌

Peripheral Port Isolation

The MC14503BF can isolate a group of peripheral port lines from a common system bus by placing the corresponding channels in the high-impedance state. This is useful when a memory card, removable module, or expansion interface must be electrically disconnected while other logic remains active. The grouped disable architecture lets four outputs disengage together and two additional outputs form a separate segment. The device's 5 V nominal operation and non-inverting logic preserve signal polarity, while the 16-pin PDIP format supports through-hole boards and repair-oriented legacy designs.

🏭

Industrial Control Backplane

The MC14503BF is appropriate for a segmented industrial control backplane where controller cards and interface modules share parallel command or status lines. Three-state outputs allow an inactive card to release the bus, and the separate disable groups provide coarse control over four-channel and two-channel sections. Its operating temperature range of -55 °C to +125 °C supports demanding environmental designs when the complete assembly meets its own qualification requirements. Engineers should evaluate bus rise time, connector loading, grounding, and contention timing before finalizing the backplane topology.

🗄️

Memory Module Data Routing

The MC14503BF can provide buffered, selectable routing for legacy memory-module data lines where the system must isolate devices during a bus transfer. Six non-inverting channels preserve data polarity, while Disable A and Disable B let the controller release two differently sized channel groups. The 150 ns delay must be included in address, chip-select, and data-valid timing, particularly around memory-access transitions. Its high-current source and sink capability is useful for driving board-level interconnects, while the 50 pF load figure provides a defined benchmark for initial signal-integrity assessment.

🔬

Legacy Test and Measurement Interface

The MC14503BF fits legacy test and measurement equipment that routes several parallel measurement-control signals to a shared connector or backplane. The 3-state outputs permit the active instrument section to drive the lines while disconnected sections remain high impedance, avoiding interference between modules. Non-inverting channels make this useful where signal polarity must remain unchanged, and two grouped disable inputs simplify board-level bus segmentation. Because this is an older through-hole logic device, verify connector pin assignments, cable capacitance, grounding, and timing before integrating it into a new measurement platform.

⚡

Multichannel Digital Control Interface

The MC14503BF can buffer several digital control lines entering a legacy controller card when the host side uses a shared multidrop connection. Disable A provides simultaneous release of four channels, while Disable B handles two additional channels, allowing the card to disconnect predictably. The 5 V nominal supply and non-inverting 3-state outputs suit conventional TTL-level logic when operating limits and levels are verified. Layout should minimize stub branches, provide a continuous ground reference, and ensure that no disabled output is relied upon as a valid data state.

What is the MC14503BF?
The MC14503BF is a hex non-inverting 3-state buffer with six outputs, high-current source and sink capability, and two disable controls. It is manufactured by onsemi in a 16-pin PDIP package and is intended primarily for common-bus applications. According to the onsemi MC14503B datasheet, Disable A controls buffers 1 through 4, while Disable B controls buffers 5 through 6.
How many channels and disable inputs does the MC14503BF have?
The MC14503BF has six non-inverting channels and two disable inputs. A high level on Disable A places the outputs of buffers 1 through 4 into the high-impedance state, while a high level on Disable B places buffers 5 through 6 into the high-impedance state. This grouped control allows a 16-pin device to manage more than one bus segment efficiently.
What is the propagation delay of the MC14503BF?
The MC14503BF has a stated propagation delay of 150 ns. This timing specification describes the interval between an input transition and the corresponding output response under the manufacturer's specified conditions. According to the onsemi MC14503B datasheet, system timing should include this delay when determining when a newly enabled driver may safely begin driving a shared bus.
Where can I download the MC14503BF datasheet PDF?
The MC14503BF datasheet PDF is available from the official onsemi document URL on this page, which points to the MC14503B datasheet. Use the manufacturer document for the authoritative pin assignments, electrical characteristics, disable truth table, and recommended operating conditions. The onsemi PDF is preferable to informal mirror pages because it reflects the manufacturer's published documentation.
Where can I find the MC14503BF pinout?
The MC14503BF pinout and pin-function descriptions are located in the pin-assignment diagram and logic diagram of the onsemi MC14503B datasheet. The device uses a 16-pin PDIP package, but the individual pin numbers should be assigned only from the manufacturer pin table rather than inferred from another 16-pin logic device. This avoids errors when connecting the two grouped disable inputs.
Can the MC14503BF drive a common bus?
Yes, the MC14503BF is specifically designed for common-bussing applications because each output can be disabled into a high-impedance state. Its non-inverting outputs preserve input logic polarity, and its high-current source and sink capability supports actively driven bus levels. Designers must still ensure that only one enabled device drives a shared node at a time to prevent output contention.
How do Disable A and Disable B work on the MC14503BF?
Disable A and Disable B independently control two groups of outputs on the MC14503BF. According to the onsemi datasheet, a high level on Disable A forces buffers 1 through 4 into the high-impedance state, and a high level on Disable B forces buffers 5 through 6 into the high-impedance state. The grouped arrangement is useful for segmented buses and coordinated bus ownership.
What is the nominal supply voltage of the MC14503BF?
The MC14503BF operates from a nominal 5 V supply. The onsemi MC14503B datasheet provides the detailed voltage limits, quiescent-current behavior, input thresholds, output characteristics, and test conditions used with that nominal value. Systems should use the manufacturer's absolute maximum and recommended operating limits rather than assuming that 5 V permits rail-to-rail excursions.
What can replace the MC14503BF?
A valid drop-in replacement for the MC14503BF must use the same 16-pin PDIP footprint, preserve pin-to-pin functions, retain the grouped disable behavior, and provide compatible 5 V electrical characteristics. No complete cross-reference result in the available records establishes that requirement for another manufacturer. Treat any generic bus-buffer substitute as a redesign candidate until its exact pinout, disable logic, timing, and loading are verified.
Is the MC14503BF the same as a standard hex bus buffer?
The MC14503BF is not interchangeable with every standard hex bus buffer because its two disable inputs control separate groups of four and two outputs. A functional equivalent must preserve non-inverting behavior, three-state operation, propagation delay, source and sink capability, and the exact 16-lead pin assignments. Confirm the device pinout and disable truth table before considering it as a replacement.
When should I choose the MC14503BF over a redesigned bus interface?
Choose the MC14503BF when an existing PCB uses its 16-pin PDIP footprint and the design needs six non-inverting, three-state channels with separate four-channel and two-channel disable groups. It is especially useful when preserving an established common-bus architecture is more important than reducing pin count or adopting a newer logic family. Verify lifecycle requirements before committing a new design.
Is the MC14503BF suitable for industrial equipment?
The MC14503BF is suitable for industrial control equipment when its published electrical limits and temperature range satisfy the system requirements. The part is listed with an operating temperature range of -55 °C to +125 °C and provides three-state outputs for shared-bus isolation. Qualification of the complete product still depends on its environment, reliability target, sourcing status, and applicable industry requirements.
Where can I request a quote for the MC14503BF?
Use the Request a Quote form on this page to request MC14503BF pricing, current availability, minimum order quantity, and lead time. Because the device is identified as obsolete, the quote response should also confirm whether the offered units are new, factory surplus, or another condition. Request a written description of the grade and inspection status before placing an order.
What is the lead time for the MC14503BF?
The current MC14503BF lead time depends on remaining factory inventory and the condition of the units available when a quote is prepared. Use the Request a Quote form on this page to request the latest availability and lead-time confirmation. Because the part is obsolete, do not base a production schedule on an unconfirmed historical delivery estimate.
What are the key specifications of MC14503BF that engineers should know?
The key MC14503BF specifications are six non-inverting 3-state channels, two grouped disable controls, 150 ns propagation delay, 5 V nominal operation, 50 pF load capability, and a 16-pin PDIP package. The onsemi datasheet also identifies high-current source and sink capability. These characteristics determine bus-loading margin, timing, disable behavior, and PCB compatibility.

엔지니어링 참조 데이터: MC14503BF — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the MC14503BF when maintaining an existing 16-pin PDIP board that depends on six non-inverting, three-state channels and two grouped disable inputs. It is particularly suitable for legacy common-bus systems in which four channels must release together and two channels must be controlled separately. Do not substitute a generic 74-series hex buffer without checking its exact pinout, enable polarity, propagation delay, output levels, and source/sink capability. A surface-mount transceiver may be preferable for a new compact design, but it requires a PCB footprint change and different timing or enable logic. Because the MC14503BF is identified as obsolete, confirm the condition, quantity, and long-term availability of the proposed units before committing to production. For ongoing new-product development, evaluate a maintained equivalent or redesign while preserving the system’s bus ownership and disable sequencing requirements.

대체품과의 비교

파라미터 이 제품
Brand onsemi
Package 16-pin PDIP
Logic Type Hex non-inverting 3-state buffer
Number of Channels 6 channels
Nominal Supply Voltage 5 V
Propagation Delay 150 ns
Load Capacitance 50 pF
Disable Controls 2 grouped disable inputs
Operating Temperature -55 °C to +125 °C
Output Capability High current source and sink capability

주요 차별점

  • Grouped three-state output control (vs Generic single-enable hex bus buffer)
  • Non-inverting signal path (vs Inverting hex transceiver)
  • Through-hole legacy PCB compatibility (vs Surface-mount-only bus buffer)

설계 노트

Ensure that only one enabled device drives any shared node. The MC14503BF uses high impedance to relinquish a bus, but two simultaneously active outputs can still contend if they attempt opposing logic levels. Define ownership and disable timing so that one driver fully releases the line before the next driver enables. Include the 150 ns propagation delay and the intended disable settling interval when sequencing bus transfers.

Keep connections to the 16-pin PDIP short and provide a continuous ground path near the device. Avoid long stub branches that add capacitance beyond the stated 50 pF load condition. When the outputs drive a connector or backplane, test the assembled interconnect because connector and PCB-trace capacitance contributes to rise time and bus settling. Maintain consistent return paths between the buffer and the devices connected to its shared lines.

Decouple the 5 V supply locally and route the return current without sharing narrow paths with high-current output loads. Although the outputs are designed with high-current source and sink capability, package and board limitations still apply to simultaneous transitions. Place the decoupling capacitor close to the supply and ground pins and check the supply voltage at the device during worst-case bus activity.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The MC14503BF is a legacy integrated circuit and is not presented as an AEC-Q100 automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed for the exact manufacturing lot and supply condition.

관련 검색

MC14503BF datasheet MC14503BF datasheet pdf MC14503BF pinout MC14503BF specifications MC14503BF equivalent MC14503BF replacement MC14503BF cross reference onsemi MC14503BF MC14503BF 16-pin PDIP MC14503BF price MC14503BF stock MC14503BF application circuit

관련 부품 & 용어

onsemi MC14503BF MC14503B hex non-inverting buffer 3-state buffer tri-state output high-impedance state common-bus interface buffer driver transceiver logic IC digital interface IC semiconductor Disable A Disable B propagation delay 150 ns propagation delay 50 pF load capacitance 5 V logic 16-pin PDIP PDIP package family through-hole technology surface-mount technology microprocessor data bus industrial control backplane memory-module data bus peripheral port isolation
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기