MC14551BFG - 4-Channel 2:1 Analog Multiplexer | onsemi
MPN: MC14551BFG ✗ 停產MC14551BFG 概覽
An analog multiplexer is a semiconductor switch that connects one common node to one of two selectable signal paths. A demultiplexer reverses that routing function, allowing a shared circuit to select among multiple inputs or outputs. The MC14551B series implements a 4PDT solid-state switch in CMOS technology, placing four independently selectable 2:1 routing sections in one device. This architecture is useful whenever a system must share a limited number of amplifiers, converters, or measurement channels.
Key features include four 2:1 switch circuits, 280 ohm on-resistance, low off-state leakage, and control over analog signals across the complete supply range. The device uses digital control inputs with triple-diode protection on the control inputs, helping protect the switching circuitry from excessive input voltage. Its 3 V to 18 V operating supply range and -55 °C to +125 °C temperature range support industrial, communications, instrumentation, and extended-temperature equipment.
The MC14551BFG is a single-ended multiplexer with four common terminals and paired switched terminals. Its CMOS implementation provides low power consumption compared with mechanical or relay-based switching while preserving analog signal paths. Because the switch resistance contributes to insertion loss and the leakage current contributes to an error floor, the selected source impedance, signal amplitude, and system bandwidth should be considered during design.
Typical applications include data acquisition systems, programmable instrumentation, sensor signal routing, communication path selection, test and measurement equipment, and industrial control systems. The device is particularly useful when several analog sources must be connected to one processing chain while keeping routing compact and repeatable.
For PCB implementation, place the device near the signal paths that it routes and keep input and output traces short to minimize parasitic capacitance and pickup. Use a stable supply reference and appropriate bypass capacitance according to the onsemi datasheet. Confirm that control logic levels meet the specified input thresholds and that every selected analog node remains within the allowable signal range.
This page combines the manufacturer-linked technical identity, exact distributor package information, drop-in replacement analysis, comparison parameters, and application-focused design guidance for engineers evaluating the MC14551BFG.
直接替換替代品,適用於 MC14551BFG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MC14551BFG (相同外形與佔位) — 差異在於 Operating Temperature Range, Switch Configuration.
MC14551BDG
✅ 直接替換聯絡詢價
查看資料表 →MC14551BDR2G
✅ 直接替換📋 參考替代品(不在目錄中)
MC14551BFG 規格
| Device Type | Quad 2:1 analog multiplexer/demultiplexer |
| Number of Switch Circuits | 4 circuits |
| Switch Configuration | 4PDT solid-state switch |
| On Resistance | 280 ohm |
| Operating Supply Voltage Range | 3 V to 18 V |
| 工作溫度範圍 | -55 °C to +125 °C |
| Control Inputs | Triple-diode protected digital control inputs |
| Analog Signal Control | Control over the complete supply-voltage range |
| Off Leakage Current | Very low off leakage current |
| Technology | CMOS |
| 封裝 | 16-pin SOIC (SOEIAJ) |
| Package Code | SOEIAJ |
| Number of Terminals | 16 |
| 安裝類型 | Surface mount |
| Package Shape | Rectangular |
| Temperature Grade | Military |
| Signal Type | Single-ended analog |
| Switch Type | 2:1 multiplexer/demultiplexer |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
| AEC-Q100 Status | not_applicable |
MC14551BFG rectangular 腳位配置指南
MC14551BFG(rectangular 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MC14551BFG.
請參閱 資料表 以查看完整腳位配置。
典型應用
MC14551BFG 適用於 6 應用s: Multichannel Sensor Signal Routing, Data Acquisition Front Ends, Programmable Test and Measurement, Industrial Control Signal Routing, Communications Path Selection, Precision Signal Conditioning.
Multichannel Sensor Signal Routing
The MC14551BFG fits sensor-selection circuits that must connect one measurement chain to several analog sources. Its four 2:1 sections provide independent routing paths, while the 280 ohm on-resistance can be manageable when the selected amplifier has sufficiently high input impedance. The 3 V to 18 V supply range supports multiple embedded and industrial systems. A buffer should be placed after the multiplexer when sensor impedance, cable capacitance, or required measurement accuracy would make the switch resistance significant.
推薦
Data Acquisition Front Ends
The MC14551BFG is useful in data-acquisition front ends that route several analog channels into shared amplification, filtering, or conversion circuitry. Four independent 2:1 paths let a controller select among sensor or conditioning outputs without using four separate analog switches. Its very low off leakage helps isolate unselected channels, although total error also depends on source impedance and downstream bias current. The 16-pin SOIC package supports compact surface-mount instrumentation with controlled PCB routing.
推薦
Programmable Test and Measurement
The MC14551BFG can select test paths in programmable instrumentation because each of its four 2:1 sections routes an analog signal according to a digital control input. It is appropriate when a multiplexer must cover the complete 3 V to 18 V supply range while maintaining a compact implementation. Designers should include the 280 ohm switch resistance in accuracy calculations and verify leakage for high-impedance measurements. The -55 °C to +125 °C range also supports extended-temperature test environments.
推薦
Industrial Control Signal Routing
The MC14551BFG can route analog command or feedback signals within industrial control equipment that uses shared input channels. The four independently addressed 2:1 switches allow one analog processing path to interact with multiple sources while keeping control logic digital. Its military temperature grade of -55 °C to +125 °C and 3 V to 18 V supply capability suit extended-temperature equipment. Layout should minimize analog trace length and keep switching-node capacitance low to preserve bandwidth.
推薦
Communications Path Selection
The MC14551BFG is suitable for low-frequency analog path selection in communications equipment, especially where several receive or transmit branches must share a common processing chain. The device controls analog signals across the complete supply-voltage range and provides four separate 2:1 sections for flexible routing. Because no high-frequency bandwidth specification is available in the identified product records, engineers should verify the datasheet limits and impedance behavior before using it in demanding RF or high-speed paths.
推薦
Precision Signal Conditioning
The MC14551BFG can be placed ahead of shared signal-conditioning stages when multiple analog nodes must feed one amplifier or filter chain. Low off leakage is beneficial for channel isolation, while the 280 ohm on-resistance determines how much the source impedance and switch network interact. For precision measurement, use high-impedance buffering and account for leakage, switch resistance, and temperature-dependent behavior in the error budget. The 16-pin surface-mount package simplifies integration into multichannel measurement boards.
推薦
推薦產品摘要
工程參考資料,適用於 MC14551BFG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MC14551BDG | MC14551BDR2G |
|---|---|---|---|
| Brand | onsemi | onsemi | onsemi |
| Package | 16-pin SOIC (SOEIAJ) | 16-pin SOIC (SOEIAJ) | 16-pin SOIC (SOEIAJ) |
| Device Type | Quad 2:1 analog multiplexer/demultiplexer | MC14551B-series analog multiplexer/demultiplexer | MC14551B-series analog multiplexer/demultiplexer |
| Switch Configuration | 4PDT solid-state switch | 4PDT solid-state switch | 4PDT solid-state switch |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits |
| Control Input Protection | Triple-diode protection | Triple-diode protection | Triple-diode protection |
| Technology | CMOS | CMOS | CMOS |
主要差異化特點
- Four independent analog selections in one package (對比MC14551BDG)
- Extended-temperature capability (對比MC14551BDR2G)
- Compact four-channel routing (對比MC14551BDG)
設計說明
Include the 280 ohm on-resistance and source impedance in the complete signal-transfer calculation. For a switched source resistance of Rsource, the divider formed by Rsource and Ron gives an ideal attenuation of Rsource divided by Rsource plus Ron. Add downstream amplifier input impedance, PCB leakage, and temperature effects when the measurement requires high accuracy.
Route common, switched, control, and supply traces to minimize parasitic capacitance and coupling between adjacent channels. Place the device close to the shared analog processing chain, keep unselected and selected paths short, and provide a quiet ground reference. If several nodes carry high-impedance signals, use guarding and clean layout techniques to reduce leakage-induced errors.
Do not assume that family-name similarity guarantees exact replacement. Confirm pin numbering, package dimensions, control-input logic thresholds, temperature grade, maximum analog signal voltage, and supply limits for MC14551BDG or MC14551BDR2G before substituting either part into an MC14551BFG design. Also verify that the control signals remain within the permitted input range at every power state.
Design the supply path so the device receives a stable voltage across the intended 3 V to 18 V range. Place the manufacturer-recommended bypass capacitor close to the supply pins and route return current directly to the ground plane. Digital control transitions can inject current into analog nodes, so maintain separation between control routing and sensitive switched paths.
合規資訊
The identified product records do not provide authoritative RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. MC14551BFG is an interface IC, so AEC-Q100 is not applicable.