MC1458PG4 - Dual 30V 1MHz Op Amp | Texas Instruments
MPN: MC1458PG4 ✓ 啟用中MC1458PG4 概覽
An operational amplifier, commonly called an op amp, is an analog amplifier with very high open-loop gain. When negative feedback surrounds the device, that gain becomes precise and stable, allowing an analog signal to be amplified according to the surrounding resistor network. A dual operational amplifier contains two amplifier sections in one package, making it useful when a board needs two related analog functions without using two separate IC packages.
The MC1458PG4's defining performance figures are its two-channel configuration, 30 V supply capability, and 1 MHz gain-bandwidth product. These characteristics position it as a general-purpose amplifier rather than a precision or high-speed signal-processing device. The 8-pin PDIP format also supports conventional through-hole assembly, breadboard prototyping, educational designs, and maintenance of existing industrial hardware.
Each amplifier section supports common analog-building functions such as voltage following, non-inverting amplification, inverting amplification, summation, subtraction, filtering, and level conditioning. Negative feedback determines the closed-loop gain, while resistor and capacitor values establish the operating characteristics of the surrounding circuit. The dual organization allows paired operations in one package, including two voltage followers or an inverting stage followed by another conditioning stage.
Typical uses include low-frequency industrial control loops, sensor-signal conditioning, audio preamplification at modest bandwidths, educational analog-circuit demonstrations, and legacy equipment repairs. The 1 MHz gain-bandwidth figure is particularly relevant for general-purpose signal paths rather than wideband video, high-fidelity audio, or precision instrumentation. System designers should calculate closed-loop bandwidth from the required gain and confirm that signal amplitude and slew-rate requirements remain compatible.
For PCB implementation, place the device so the eight leads can be inspected and routed cleanly, maintain separation between input and output paths, and provide local supply bypassing where practical. Stable operation depends on suitable feedback compensation, adequate supply bypassing, and keeping source impedances low enough for the selected gain. The two channels are intended for similar analog environments and do not eliminate the need to verify common-mode, output-swing, and stability limits in the finished design.
This product reference combines the manufacturer's key amplifier ratings, package information, sourcing guidance, documented drop-in alternatives, and practical selection advice. It is intended to help engineers identify whether the MC1458PG4 fits an existing 8-pin dual-op-amp design and what electrical and layout checks to complete before production release.
直接替換替代品,適用於 MC1458PG4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MC1458PG4 (相同外形與佔位) — 差異在於 Package, RoHS Status.
MC1458P
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →RC4558P
✅ 直接替換📋 參考替代品(不在目錄中)
MC1458PG4 最大額定值與電氣特性
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifier Channels | 2 channels |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1 MHz |
| 封裝 | 8-pin PDIP, 0.300 inch pitch |
| 安裝類型 | Through-hole |
| RoHS 狀態 | Compliant |
MC1458PG4 腳位配置
| 腳位 1 | OFFSET NULL 1 — Offset null connection for amplifier section 1 |
| 腳位 2 | IN1- — Inverting input for amplifier section 1 |
| 腳位 3 | IN1+ — Non-inverting input for amplifier section 1 |
| 腳位 4 | V- — Negative supply connection |
| 腳位 5 | OFFSET NULL 2 — Offset null connection for amplifier section 2 |
| 腳位 6 | OUT1 — Output for amplifier section 1 |
| 腳位 7 | OUT2 — Output for amplifier section 2 |
| 腳位 8 | V+ — Positive supply connection |
典型應用
MC1458PG4 適用於 6 應用s: Industrial Sensor Signal Conditioning, Audio Preamplifier and Mixer Stage, Voltage Follower and Buffering, Analog Difference Amplifier, Legacy Control-System Maintenance, Analog Education and Prototyping.
Industrial Sensor Signal Conditioning
The MC1458PG4 suits low-frequency industrial sensor-conditioning paths that require two amplifier sections in one 8-pin PDIP device. Each channel can implement a non-inverting or inverting stage around the MC1458's 1 MHz gain-bandwidth product, allowing a low-level sensor signal to be scaled before an ADC or controller input. The 30 V supply ceiling also fits many legacy 24 V industrial analog boards. Check input bias current and common-mode limits against the sensor impedance, and keep sensitive input traces short and away from switching nodes.
Audio Preamplifier and Mixer Stage
For conventional low-bandwidth audio preamplification, the MC1458PG4 can provide independent gain or mixing functions in a single 8-pin PDIP package. Its 1 MHz gain-bandwidth product is appropriate for many voice-band and general-purpose audio paths, while the 30 V supply rating supports higher-voltage legacy signal stages. The design should use negative feedback to set the closed-loop gain and should verify output swing, slew rate, and channel-to-channel behavior for the intended signal level.
Voltage Follower and Buffering
The two MC1458PG4 amplifier sections can each operate as a voltage follower, creating useful buffers between high-impedance sources and downstream measurement or control circuits. A follower isolates the source from the next stage without intentionally setting voltage gain, while the 1 MHz gain-bandwidth product gives ample bandwidth for many low-frequency measurement signals. Use low-value feedback resistors where noise or bias-current effects are important, and verify that source and load conditions remain within the amplifier's input and output limits.
Analog Difference Amplifier
MC1458PG4 is suitable for a difference-amplifier arrangement in which two analog inputs are compared and the result is scaled for an ADC, comparator interface, or control loop. Its dual-section architecture supports paired gain and subtraction operations, while the 30 V maximum supply rating is useful in legacy ±15 V or lower single-supply systems. Resistor matching determines common-mode rejection, so precision applications should account for tolerance and temperature drift rather than relying on the amplifier's nominal 1 MHz bandwidth alone.
Legacy Control-System Maintenance
The MC1458PG4 is a practical candidate for repairing or extending legacy industrial and laboratory control boards that use a dual general-purpose op amp in an 8-pin PDIP footprint. Its 1 MHz gain-bandwidth product and 30 V supply rating match the operating class of many older analog-control designs. Confirm the original pin assignments, supply tolerances, output-load conditions, and stability requirements before replacement. Through-hole construction also simplifies socketed diagnosis and board-level rework in equipment that no longer uses modern surface-mount packages.
Analog Education and Prototyping
MC1458PG4 supports laboratory exercises and prototypes involving voltage followers, inverting amplifiers, summing networks, integrators, and active filters. Two amplifiers in one 8-pin DIP package allow students to compare channels and construct multistage analog functions without immediately moving to a surface-mount package. Because the device is a general-purpose 1 MHz amplifier, experiments should emphasize feedback, biasing, signal-range limits, and practical measurements rather than precision instrumentation or wideband performance.
工程參考資料,適用於 MC1458PG4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MC1458P | RC4558P |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Analog Devices |
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Amplifier Configuration | Dual | Dual | Dual |
| Product Class | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Mounting Style | Through-hole | Through-hole | Through-hole |
主要差異化特點
- Closest same-family ordering alternative (對比MC1458P)
- Established manufacturer lineage for legacy designs (對比RC4558P)
- Two independent amplifier sections in one through-hole package (對比MC1458P)
設計說明
Keep each feedback resistor and its associated input or output connection as short as practical. In a dual amplifier, maintain separation between channel 1 and channel 2 signal paths, particularly when one channel handles a high-level signal and the other handles a low-level sensor input. Place the device to provide an unobstructed ground return and avoid routing sensitive inputs beneath power-supply traces or near high-current switching paths.
Design the supply network for the amplifier's maximum 30 V operating envelope rather than assuming the nominal board voltage is safe under transients. Confirm absolute maximum limits, common-mode input range, and output-swing behavior in the manufacturer datasheet. Add local supply bypassing close to the device and use separate, low-impedance routing for each supply rail so current transients do not create voltage disturbances across the analog signal path.
Do not treat an 8-pin DIP outline as proof that every dual operational amplifier is interchangeable. Before fitting MC1458P or RC4558P, compare offset null availability, input polarity, supply pins, output assignments, input bias current, common-mode range, output swing, and stability with feedback. In particular, a circuit designed around one amplifier's offset-null arrangement may require component or layout changes even when the package can physically fit.
合規資訊
The MC1458PG4 is listed as RoHS compliant. No explicit REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement is established for this exact ordering option.