TLV2760IP - 500kHz RRIO Op Amp with Shutdown | Texas Instruments
MPN: TLV2760IP ✓ 啟用中TLV2760IP 概覽
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TLV2760 belongs to the operational-amplifier hierarchy, which includes rail-to-rail amplifiers, micropower amplifiers, and general-purpose analog ICs. Rail-to-rail input operation allows the input common-mode range to extend close to the supply rails, while rail-to-rail output operation improves output swing in low-voltage systems.
The TLV2760 family provides 500 kHz bandwidth from approximately 20 microamperes of quiescent current and supports operation down to 1.8 V. The TLV2760IP is the high-offset-voltage member of the family, with a listed offset-voltage rating of 3500 microvolts. Its shutdown function allows a system designer to reduce supply current when the amplifier is not required, which is valuable in portable and battery-powered equipment.
The low operating voltage and rail-to-rail behavior make the device suitable for sensor interfaces, transducers, battery-powered instrumentation, audio signal paths, and embedded control systems. Its 500 kHz bandwidth provides enough bandwidth for general-purpose feedback and error-amplifier networks without the higher power and noise associated with much faster amplifiers.
The 8-pin PDIP package supports through-hole assembly and prototype rework, while its exposed lead spacing follows the standard 8-pin PDIP footprint. Designers should verify the shutdown-logic polarity, input bias behavior, output swing, and stability requirements against the manufacturer datasheet before using the amplifier near supply limits.
This page combines the TLV2760IP electrical characteristics, lifecycle information, package data, sourcing workflow, and practical replacement guidance. It also highlights the distinctions among TLV276x offset-voltage options so engineers can select a pin-compatible family member without overlooking offset or shutdown requirements.
直接替換替代品,適用於 TLV2760IP — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TLV2760IP (相同外形與佔位) — 差異在於 Amplifier Type, Number of Circuits, Package.
TLV2761IP
✅ 直接替換聯絡詢價
查看資料表 →TLV2762IP
✅ 直接替換聯絡詢價
查看資料表 →TLV2763IP
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2760IP 最大額定值與電氣特性
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Nominal Supply Voltage | 3.6 V |
| Gain-Bandwidth Product | 500 kHz |
| 靜態電流 | 20 microamperes typical |
| Input Rail-to-Rail | Yes |
| Output Rail-to-Rail | Yes |
| Shutdown Control | Yes |
| Offset Voltage | 3500 microvolts |
| Operating Temperature Class | Industrial temperature range |
| 封裝 | 8-pin PDIP, 0.300 inch pitch |
| 安裝類型 | Through-hole |
| 輸出類型 | Rail-to-rail |
| Product Category | General-purpose amplifier |
TLV2760IP 8-pin pdip, 0.300 inch pitch 腳位配置指南
TLV2760IP(8-pin pdip, 0.300 inch pitch 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TLV2760IP.
請參閱 資料表 以查看完整腳位配置。
典型應用
TLV2760IP 適用於 6 應用s: Battery-Powered Sensor Signal Conditioning, Portable Instrumentation, Low-Voltage Audio Preamplifier, Industrial Control Interface, Transducer and Bridge-Signal Amplifier, Embedded Control Signal Conditioning.
Battery-Powered Sensor Signal Conditioning
The TLV2760IP fits low-voltage sensor front ends because it operates down to 1.8 V, supports rail-to-rail input and output, and uses approximately 20 microamperes of quiescent current. It can amplify a sensor signal close to either supply rail before conversion or sampling. The shutdown function reduces current demand when sensing is intermittent. Because this TLV2760 version has a 3500 microvolt offset-voltage rating, it is most appropriate when the downstream system can tolerate that offset or when offset is corrected through calibration.
Portable Instrumentation
Portable measurement equipment benefits from the TLV2760IP's low 1.8 V minimum operating voltage and approximately 20 microamperes supply demand. Its 500 kHz gain-bandwidth product is suitable for conditioning moderate-frequency signals without requiring a high-speed amplifier. Rail-to-rail input capability preserves measurement range near the supply limits, while rail-to-rail output improves drive into a following converter or instrumentation stage. Verify the 3500 microvolt offset specification against the required measurement resolution.
Low-Voltage Audio Preamplifier
The TLV2760IP can provide input and output swing close to the rails in a low-voltage audio preamplifier, which helps preserve headroom in portable playback systems. Its 500 kHz bandwidth covers common audio-band signal conditioning, while approximately 20 microamperes of quiescent current limits continuous power use. The shutdown control can disable the amplifier between active intervals. For high-fidelity designs, compare the device's offset, noise, and output-drive characteristics with the selected audio requirements.
Industrial Control Interface
The TLV2760IP is applicable to low-voltage industrial interface circuits that require rail-to-rail input operation, such as conditioning a controller signal or driving a slow analog input. Its approximately 20 microamperes quiescent current supports distributed low-power sensing, and the shutdown function permits controlled operating states. The industrial temperature-range designation supports industrial environments, but designers should verify absolute maximum ratings, input bias current, and offset stability for the specific control loop.
Transducer and Bridge-Signal Amplifier
For low-level transducer signals, the TLV2760IP's rail-to-rail input and output behavior can be useful when the transducer operates close to the available supply range. The 500 kHz gain-bandwidth product supports practical audio-band and instrumentation bandwidth, and the shutdown function allows the amplifier to remain off outside measurement intervals. Check the TLV2760IP's 3500 microvolt offset rating, input bias current, and noise against the transducer's sensitivity before choosing the final gain configuration.
Embedded Control Signal Conditioning
The TLV2760IP can condition sensor, feedback, or reference signals around a low-voltage embedded controller. Its 500 kHz bandwidth supports general-purpose amplifier networks, and operation down to 1.8 V allows use with low-energy supply rails. Rail-to-rail inputs reduce common-mode headroom concerns, while the shutdown input permits power-state management. Ensure the controller's ADC input range, amplifier stability with the selected feedback network, and settling requirements are satisfied before deployment.
工程參考資料,適用於 TLV2760IP — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2761IP | TLV2762IP | TLV2763IP |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP (P) | 8-pin PDIP (P) | 8-pin PDIP (P) | 8-pin PDIP (P) |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 500 kHz | 500 kHz | 500 kHz | 500 kHz |
| Minimum Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Quiescent Current | Approximately 20 microamperes | Approximately 20 microamperes | Approximately 20 microamperes | Approximately 20 microamperes |
| Input and Output Operation | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shutdown Control | Yes | Yes | Yes | Yes |
| Offset Voltage | 3500 microvolts | Different family offset class; consult the TLV276x ordering table | Different family offset class; consult the TLV276x ordering table | Different family offset class; consult the TLV276x ordering table |
主要差異化特點
- Shutdown control in a through-hole operational-amplifier package (對比TLV2761IP)
- Rail-to-rail operation from a low 1.8 V supply (對比TLV2762IP)
- Low-power operation with approximately 20 microamperes quiescent current (對比TLV2763IP)
設計說明
Estimated: at a 3.6 V supply and 20 microamperes quiescent current, the TLV2760IP consumes approximately 72 microwatts before output-current and load effects. When shutdown is not required continuously, drive the shutdown pin from a compatible control signal to reduce supply demand. Confirm the shutdown polarity, transition timing, and leakage behavior in the manufacturer datasheet before using the control pin in a power-sequencing scheme.
Do not treat rail-to-rail input as unlimited input range. The amplifier still has absolute maximum input-voltage and supply limits, so inputs must remain within the permitted common-mode and overvoltage boundaries. Also account for the TLV2760IP's 3500 microvolt offset-voltage rating in precision DC measurements; system offset calibration may reduce static error but cannot correct input-voltage drift or noise.
Place the input, feedback, bypass, and decoupling components close to their associated amplifier pins to minimize parasitic capacitance and feedback-loop delay. Keep output and feedback routing away from shutdown traces and other high-impedance shutdown control lines. For sensitive sensor inputs, use a quiet ground reference and avoid routing the input directly beside switching nodes or digital clock lines.
The 500 kHz gain-bandwidth product limits useful closed-loop bandwidth according to the selected noise gain and feedback factor. Avoid assuming that a 500 kHz gain-bandwidth product supports a 500 kHz closed-loop signal in every topology. Check the required gain, settling tolerance, output-capacitive-load limits, and feedback-network values against the manufacturer stability and frequency-response information.
合規資訊
Compliance status is not stated in the manufacturer product-page snippet or distributor results used for this listing. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation with Texas Instruments before environmental or regulatory qualification.