MC9S08PB16VTG - 8-Bit 20MHz 16KB Flash MCU | NXP | Motor Control
MPN: MC9S08PB16VTG ✓ 啟用中MC9S08PB16VTG 概覽
A microcontroller is a programmable semiconductor that integrates a CPU, memory, and peripherals on one die. The S08 architecture belongs to the broader embedded-controller hierarchy, combining an 8-bit processor core with analog measurement, communication, timing, and control functions. MC9S08PB16 devices reduce external component count by placing functions such as a 12-bit ADC, analog comparator, amplifier, I2C interface, and timers on the same device.
The MC9S08PB16VTG supports bus operation up to 20 MHz over 2.7 V to 5.5 V, with 16 KB of Flash and 1 KB of RAM. Up to 30 interrupt and reset sources and four-level nested interrupt support help organize real-time control tasks. The 5 V-capable architecture also allows operation in industrial and appliance environments where a 3.3 V-only interface would be insufficient.
The S08PB family combines an economical 8-bit CPU with rich analog resources. A 12-bit ADC supports sensor and process measurements, while the integrated comparator and amplifier support threshold detection and low-level analog conditioning. I2C provides a two-wire peripheral bus, and flexible timer resources support PWM, capture, periodic events, and motor-control timing. These integrated blocks can reduce board area and the need for separate analog or timing ICs.
Typical uses include small brushless or simple motor controllers, appliance user interfaces, temperature and pressure sensing, industrial controls, and compact sensor modules. The part is especially suitable when designers need legacy 5 V compatibility, low-cost Flash programmability, and analog integration without adopting a larger 32-bit MCU. The 16-pin TSSOP package also supports compact through-hole PCB assembly.
Designers should preserve adequate decoupling between the supply pins and analog source, keep analog and high-current switching traces physically separated, and validate timer settings against the required PWM frequency. The operating voltage, clock configuration, reset behavior, and peripheral pin multiplexing should be confirmed from the MC9S08PB16 datasheet before layout release and firmware deployment.
直接替換替代品,適用於 MC9S08PB16VTG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MC9S08PB16VTG (相同外形與佔位) — 差異在於 Package, Flash Memory, Nested Interrupt Levels, Serial Interface, Timer Resources.
MC9S08PT16VTG
✅ 直接替換聯絡詢價
查看資料表 →MC9S08PB16VTG 最大額定值與電氣特性
| CPU Architecture | 8-bit S08 central processor unit |
| Maximum Bus Frequency | 20 MHz |
| Flash Program Memory | 16 KB |
| RAM | 1 KB |
| Operating Voltage Range | 2.7 V to 5.5 V |
| ADC Resolution | 12 bit |
| Analog Comparator | Integrated |
| Operational Amplifier | Integrated |
| Serial Interface | I2C |
| Timer Resources | Flexible timers with PWM and capture functions |
| Interrupt and Reset Sources | Up to 30 sources |
| Nested Interrupt Levels | Up to 4 levels |
| 封裝 | 16-pin TSSOP |
| Package Width | 4.40 mm |
| 安裝類型 | Surface mount |
| Program Memory Type | Flash |
| Low-Voltage Detection | Integrated |
| Power-On Reset | Integrated |
| Watchdog Timer | Integrated |
| Pulse-Width Modulation | Integrated |
MC9S08PB16VTG 4.40 mm 腳位配置指南
MC9S08PB16VTG(4.40 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: MC9S08PB16VTG.
請參閱 資料表 以查看完整腳位配置。
典型應用
MC9S08PB16VTG 適用於 6 應用s: Small Motor Control, Industrial Sensor Node, Appliance User Interface, Temperature and Pressure Monitoring, I2C Sensor Hub, 5 V Embedded Control Module.
Small Motor Control
MC9S08PB16VTG fits cost-sensitive small motor controllers because it combines a 20 MHz S08 CPU, flexible timers, PWM, a 12-bit ADC, and a 5 V-compatible supply range in a 16-pin TSSOP. The ADC can sample position, current, or temperature inputs, while timer-generated PWM can command a driver stage. Using an 8-bit MCU reduces instruction-cycle and memory overhead compared with a larger 32-bit control MCU. The design should still include appropriate gate-driver circuitry, current protection, and a power stage sized for the motor.
推薦
Industrial Sensor Node
The MC9S08PB16VTG is useful for compact industrial sensor nodes that need local signal conditioning and control without a high-cost MCU. Its 12-bit ADC measures analog inputs, the integrated comparator provides threshold detection, and the amplifier can support low-level signal conditioning. At up to 20 MHz, the S08 CPU can combine measurement, filtering, status handling, and communications logic. The 2.7 V to 5.5 V range also supports both lower-voltage industrial subsystems and legacy 5 V sensors, subject to each peripheral's electrical limits.
推薦
Appliance User Interface
MC9S08PB16VTG suits appliance and user-interface modules that combine a small display or indicator set with analog sensing. Its 16 KB Flash provides room for application code, 1 KB of RAM supports compact state management, and the integrated timers can handle periodic UI updates or button scanning. The 5 V operating capability is valuable in appliance electronics that already use a 5 V rail, while I2C can connect compatible peripherals. Pin multiplexing and timing should be checked against the selected display and keypad architecture.
推薦
Temperature and Pressure Monitoring
MC9S08PB16VTG can act as the local controller in a temperature or pressure monitoring product. The 12-bit ADC digitizes the analog sensor output, the comparator can provide fast limit detection, and the 20 MHz S08 CPU can perform scaling, calibration, filtering, and alarm logic. I2C supports compatible digital sensors or configuration devices, while the integrated watchdog and reset functions help maintain reliable embedded operation. For accurate measurements, the analog input path, reference strategy, grounding, and PCB thermal gradients must follow the device's recommended application circuit.
推薦
I2C Sensor Hub
MC9S08PB16VTG works well as a compact I2C sensor hub in compact industrial or appliance equipment. It can poll compatible sensors, validate responses, translate measurements into local control actions, and maintain an interrupt-driven update schedule using its nested interrupt capability. The 16-pin TSSOP keeps the controller footprint small, and Flash allows firmware to be updated when product functionality changes. Designers should confirm I2C timing, address conflicts, pull-up voltage, bus capacitance, and peripheral mapping before finalizing the PCB.
推薦
5 V Embedded Control Module
MC9S08PB16VTG is appropriate for compact 5 V embedded-control modules that need an economical CPU, nonvolatile program memory, and analog inputs without the overhead of a 32-bit processor. Its 16 KB Flash supports dedicated control code, 1 KB of RAM accommodates small working sets, and the up-to-20-MHz S08 bus provides deterministic instruction throughput. Compatibility with existing 5 V sensors and interface circuits simplifies integration, although brownout, clock-startup, and peripheral reset behavior must be evaluated for the final power architecture.
推薦
推薦產品摘要
工程參考資料,適用於 MC9S08PB16VTG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MC9S08PT16VTG |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 16-pin TSSOP | 16-pin TSSOP |
| CPU Architecture | 8-bit S08 | 8-bit S08P family |
| Operating Voltage Range | 2.7 V to 5.5 V | 5 V family |
| Pin Compatibility | MC9S08PB16VTG TSSOP-16 land pattern | Manufacturer-described as pin-compatible with the S08 family |
主要差異化特點
- Established S08PB configuration for compact embedded control (對比MC9S08PT16VTG)
- Integrated rich-analog resources reduce external circuitry (對比MC9S08PT16VTG)
- Broad 5 V-compatible operating range (對比MC9S08PT16VTG)
設計說明
Place the device-side supply decoupling capacitor close to the MCU power pins and return it through a short ground path. Keep analog inputs away from PWM outputs, motor-switching nodes, and high-current return paths. Because the TSSOP-16 lead pitch limits routing density, assign analog and digital functions from the datasheet pin table before committing the board outline and component placement.
Confirm the clock source, bus timing, and reset behavior with the 2.7 V to 5.5 V operating range in mind. Validate maximum clock operation at the intended supply voltage and temperature. For analog measurement channels, follow the recommended source impedance and sampling requirements; long traces and insufficient settling time can degrade the effective resolution of the 12-bit ADC.
Do not treat the generic S08-family designation as proof that every PB and PT device has identical peripherals. Before substituting MC9S08PT16VTG, compare pin multiplexing, ADC channels, timer channels, I2C behavior, interrupt vectors, watchdog implementation, clock settings, and memory size. Validate the existing firmware or port it through the manufacturer-supported development environment.
合規資訊
Compliance attributes are not explicitly stated for this exact MPN in the manufacturer product information and datasheet excerpts. IEC 60730 is mentioned for the NXP MC9S08PT16VTG family positioning, but it is not treated as an AEC-Q100 or exact-part compliance claim.