MCP3423T-E/MF - 18-Bit Dual-Channel Sigma-Delta ADC | Microchip
MPN: MCP3423T-E/MF ✓ 啟用中MCP3423T-E/MF 概覽
A sigma-delta ADC is a class of analog-to-digital converter that uses continuous-time delta-sigma modulation and digital filtering to convert analog voltages into high-resolution digital codes. It belongs to the ADC and DAC category within data-converter ICs and is used when low noise, good linearity, and precise measurement matter more than very high conversion speed.
The MCP3423 provides two differential measurement channels and up to 18 bits of resolution. Its internal 2.048 V reference simplifies system design by removing the need for an external precision reference in common bipolar-input applications. The two-wire I2C interface reduces the number of required signal lines, while 3.75 SPS conversion capability is suited to slow-changing industrial, environmental, and instrumentation signals.
Its delta-sigma architecture inherently shapes quantization noise toward lower frequencies, helping reject broadband noise when the analog signal bandwidth is limited. The on-board reference and differential inputs are particularly useful for sensor bridges, pressure transducers, current measurements, and low-level instrumentation. Because the converter averages successive samples through digital filtering, input settling and filter behavior must be considered when measuring rapidly changing signals.
Typical uses include industrial process monitoring, precision temperature measurement, bridge-sensor acquisition, laboratory instrumentation, and low-speed data-acquisition systems. The 3 x 3 mm DFN package supports compact designs but requires careful PCB layout, exposed-pad soldering, and low-noise routing. The MCP3423T-E/MF is packaged on tape and reel for automated manufacturing.
For best results, use suitable filtering at each analog input, keep the I2C traces short, provide clean supply and ground connections, and follow the manufacturer datasheet's exposed-pad land pattern. Differential input measurements also require attention to common-mode voltage, source impedance, and conversion timing when calculating measurement uncertainty.
This page combines the manufacturer's core device characteristics with practical analog-layout guidance, application analysis, and same-package replacement information. It highlights where the 18-bit resolution, differential architecture, 2.048 V reference, and 3.75 SPS rate make the MCP3423T-E/MF an effective precision-measurement ADC rather than a high-speed data-conversion solution.
直接替換替代品,適用於 MCP3423T-E/MF — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP3423T-E/MF (相同外形與佔位) — 差異在於 Digital Interface, Package, Conversion Rate, Resolution, Automatic Calibration.
MCP3423-E/MF
✅ 直接替換聯絡詢價
查看資料表 →MCP3423T-E/UN
✅ 直接替換聯絡詢價
查看資料表 →MCP3423T-E/MF 最大額定值與電氣特性
| 解析度 | 18 bit |
| Number of Channels | 2 differential-input channels |
| ADC Architecture | 1-channel sigma-delta per differential input channel |
| Conversion Rate | 3.75 samples per second |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | ±2.048 V |
| Digital Interface | I2C serial interface |
| 供應電壓 | 3.3 V to 5 V |
| 封裝 | 10-VFDFN exposed-pad package, 3 x 3 mm |
| 安裝類型 | Surface mount |
| Packaging | Tape and reel |
| Analog Input Type | Differential |
MCP3423T-E/MF 10-vfdfn exposed-pad package, 3 x 3 mm 腳位配置指南
MCP3423T-E/MF(10-vfdfn exposed-pad package, 3 x 3 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP3423T-E/MF.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP3423T-E/MF 適用於 6 應用s: Precision Bridge Sensor Acquisition, Industrial Temperature Measurement, Current and Voltage Monitoring, Environmental and Gas Sensor Readout, Laboratory Instrumentation, Low-Speed Data Acquisition.
Precision Bridge Sensor Acquisition
The MCP3423T-E/MF suits Wheatstone bridge and strain-gauge measurement systems because it provides two differential input channels and up to 18 bits of resolution. The differential topology rejects common-mode voltage and reduces sensitivity to ground noise, while the internal 2.048 V reference gives the converter a defined measurement span of ±2.048 V. Install matched input filtering and balance the bridge network so both channels present similar impedance. The 3.75 SPS conversion rate is appropriate for slowly changing mechanical variables such as load, pressure, or displacement.
推薦
Industrial Temperature Measurement
The MCP3423T-E/MF can acquire resistive sensor or conditioned temperature signals when high resolution matters more than rapid sampling. Its 18-bit conversion resolution and differential inputs help distinguish small changes in bridge or resistive networks, while the 2.048 V internal reference removes the routine need for a separate reference source. At 3.75 samples per second, the converter supports thermal monitoring, environmental chambers, and temperature-control loops whose signals change gradually. The analog front end must still provide excitation, current limiting, and any required linearization.
推薦
Current and Voltage Monitoring
The MCP3423T-E/MF is suitable for low-level current or voltage monitoring when the measured differential signal fits the ±2.048 V input range. Two differential channels allow simultaneous monitoring of two related quantities, and the 18-bit resolution can represent small changes across a suitably scaled shunt or sensor output. The I2C interface supports straightforward connection to a controller in industrial monitoring equipment. Input protection, filtering, and scaling must be designed so transients and common-mode voltage remain outside the converter’s operating limits.
推薦
Environmental and Gas Sensor Readout
The MCP3423T-E/MF can digitize conditioned outputs from environmental, gas, and humidity sensors when the sensor signal is slow and differential. The 18-bit resolution improves the useable resolution of low-amplitude sensor outputs, while the internal 2.048 V reference supports repeatable ratiometric measurements when the sensor and converter share a suitable reference arrangement. Its two channels can monitor a sensor and a compensation signal. Digital filtering inherent to the delta-sigma architecture helps suppress high-frequency noise, but signal bandwidth must be limited appropriately.
推薦
Laboratory Instrumentation
The MCP3423T-E/MF is appropriate for laboratory and bench instrumentation that measures slow, high-resolution analog quantities. Its differential inputs help reject interference, the 2.048 V internal reference simplifies system calibration, and the I2C interface allows a controller to configure and retrieve conversion results. Two channels support reference and measurement monitoring in compact instruments. Because the conversion rate is 3.75 samples per second, waveform capture is not appropriate; the device instead targets meters, loggers, laboratory monitors, and calibration equipment with quasi-static inputs.
推薦
Low-Speed Data Acquisition
The MCP3423T-E/MF fits compact data-acquisition modules that monitor slow-changing voltages with high resolution. Its two differential channels reduce wiring complexity and improve noise immunity compared with single-ended measurements, while the 18-bit conversion core preserves fine detail in scaled sensor outputs. The I2C bus supports connection to embedded controllers, and the 3 x 3 mm DFN package helps minimize board area. Designers should treat the converter as a precision measurement element rather than a general-purpose oscilloscope ADC and account for digital-filter settling after each conversion.
推薦
推薦產品摘要
工程參考資料,適用於 MCP3423T-E/MF — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP3423-E/MF | MCP3423T-E/UN |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 10-VFDFN (3 x 3 mm) | 10-VFDFN (3 x 3 mm) | 10-VFDFN (3 x 3 mm) |
| Resolution | 18 bit | 18 bit | 18 bit |
| Input Channels | 2 differential inputs | 2 differential inputs | 2 differential inputs |
| Conversion Rate | 3.75 samples per second | 3.75 samples per second | 3.75 samples per second |
| Internal Reference | 2.048 V | 2.048 V | 2.048 V |
| Differential Input Range | ±2.048 V | ±2.048 V | ±2.048 V |
| Digital Interface | I2C | I2C | I2C |
| ADC Architecture | Delta-sigma | Delta-sigma | Delta-sigma |
| Ordering-Code Difference | MCP3423T-E/MF | T ordering code omitted | Package code changes from MF to UN |
主要差異化特點
- Dual differential inputs in a compact package (對比MCP3423-E/MF)
- Same conversion core with an alternate assembly ordering code (對比MCP3423T-E/UN)
- Integrated precision reference simplifies bipolar measurement (對比MCP3423-E/MF)
設計說明
Route each differential input as a short pair with consistent geometry and a continuous ground reference. Place input-series resistors and anti-alias capacitors close to the analog pins, using matched components for both channels when channel matching is important. Keep switching-regulator paths, high-current returns, and digital clock traces away from the MCP3423 input nodes to minimize conversion errors.
Follow the manufacturer datasheet land pattern for the 10-VFDFN exposed-pad package. The exposed pad is both a thermal and electrical connection; provide adequate ground-plane area, solder it according to the manufacturer’s assembly guidance, and avoid unintended thermal coupling from nearby heat sources. Verify paste volume, reflow profile, and via placement with the assembly capability in mind.
Do not treat the 3.75 samples per second rating as a general-purpose sampling rate. Allow for digital-filter settling, and use an anti-alias filter appropriate for the measurement bandwidth. Also check input common-mode voltage, source impedance, and differential range before applying a signal. These checks prevent overload and prevent the converter’s high resolution from being undermined by noise or imbalance.
合規資訊
The manufacturer identifies the MCP3423 as an automotive-capable family member, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement is stated for the exact ordering code. AEC-Q100 qualification should be confirmed against the exact Microchip ordering and qualification documentation.