MCP6054-E/ST - 4-Channel 1.8V Precision Op Amp | Microchip
MPN: MCP6054-E/ST ✓ 啟用中MCP6054-E/ST 概覽
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. A precision op amp adds low input offset voltage, low input bias current, and stable operation near the supply rails. The MCP6054 belongs to the hierarchy of operational amplifiers, analog amplifiers, analog signal-chain ICs, and semiconductor-based signal-conditioning devices. Its four amplifiers share a common package while providing independent signal-conditioning channels.
The MCP6054 family combines low quiescent current of approximately 30 µA per amplifier with low offset voltage and unity-gain stability. These characteristics make it suitable for portable instrumentation, battery-powered measurement systems, sensor interfaces, and low-voltage signal-processing boards. Rail-to-rail input behavior improves usable input range near the supply limits, while rail-to-rail output capability helps preserve signal swing at low supply voltages.
The 385 kHz typical gain-bandwidth product supports applications requiring modest closed-loop bandwidth, including buffer, amplifier, and general-purpose analog stages. The maximum input offset voltage of ±150 µV is particularly useful when multiple amplifiers operate at similar gain levels and channel-to-channel offset matching affects measurement accuracy. Unity-gain stability also allows the same device to be used directly as a voltage follower without compensation external networks.
Typical uses include portable sensor interfaces, low-power data-acquisition front ends, battery-operated monitoring equipment, analog signal conditioning, and precision current or voltage measurements. In these systems, the low operating voltage and low quiescent current help control power consumption, while the low offset specification supports accurate amplification of small signals. Designers should still account for input common-mode limits, output swing, noise, stability, and the bandwidth required by the intended feedback network.
For PCB implementation, use the manufacturer's pinout and land pattern for the 14-lead TSSOP, place input and output components close to their associated pins, and provide an adequate bypass connection from the supply pins to ground. Decoupling capacitors should be selected according to the manufacturer application guidance, while the feedback network must preserve the gain-bandwidth and stability limits of the selected amplifier configuration.
This product page combines manufacturer specifications, a complete application-oriented engineering overview, same-footprint alternatives, and practical PCB guidance. It is designed to help engineers determine whether the MCP6054-E/ST provides the required precision, voltage range, power consumption, and package fit before committing the part to a new analog design.
直接替換替代品,適用於 MCP6054-E/ST — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MCP6054T-E/ST
✅ 直接替換📋 參考替代品(不在目錄中)
MCP6034-E/ST
✅ 直接替換聯絡詢價
查看資料表 →MCP604T-I/ST
✅ 直接替換📋 參考替代品(不在目錄中)
MCP6004T-E/ST
✅ 直接替換📋 參考替代品(不在目錄中)
MCP6054-E/SL
✅ 直接替換聯絡詢價
查看資料表 →MCP6054-E/ST 最大額定值與電氣特性
| Number of Channels | 4 channels |
| Amplifier Type | Precision operational amplifier |
| Minimum Single Supply Voltage | 1.8 V |
| Typical Gain-Bandwidth Product | 385 kHz |
| Maximum Input Offset Voltage | ±150 µV |
| Quiescent Current per Amplifier | 30 µA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Gain Stability | Unity-gain stable |
| Technology | CMOS |
| Temperature Grade | E temperature grade |
| 封裝 | 14-lead TSSOP, 4.40 mm width |
| 安裝類型 | Surface mount |
MCP6054-E/ST 14-lead tssop, 4.40 mm width 腳位配置指南
MCP6054-E/ST(14-lead tssop, 4.40 mm width 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP6054-E/ST.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP6054-E/ST 適用於 6 應用s: Portable Sensor Signal Conditioning, Battery-Powered Data Acquisition, Precision Voltage Buffering, Low-Voltage Instrumentation, Low-Noise Analog Signal Conditioning, Power and Control Monitoring.
Portable Sensor Signal Conditioning
The MCP6054-E/ST suits portable sensor front ends because it operates from a single supply as low as 1.8 V while drawing approximately 30 µA per amplifier. Rail-to-rail input operation helps accept sensor signals near the supply limits, and the ±150 µV maximum input offset supports accurate measurement of small analog signals. Four independent channels can condition outputs from separate sensors or monitor several points in a compact instrument. The amplifier is unity-gain stable for direct voltage-following, while its 385 kHz typical gain-bandwidth product handles sensor signals within a modest bandwidth range. Confirm the sensor output range, common-mode limits, and required closed-loop gain before finalizing the interface.
推薦
Battery-Powered Data Acquisition
The MCP6054-E/ST is appropriate for battery-powered data-acquisition systems that need several low-power analog channels. Its 1.8 V minimum supply operation supports compact energy-harvesting and portable-instrument architectures, while the roughly 30 µA per-amplifier quiescent current reduces the standing load on the battery. The maximum input offset voltage of ±150 µV helps preserve measurement integrity for slowly varying or low-amplitude sensor signals. Four channels can process multiple inputs without requiring four separate packages, reducing board area. The engineer should verify output settling time, noise, load drive, and the bandwidth required by the acquisition rate; unity-gain stability is useful for direct sensor buffering.
推薦
Precision Voltage Buffering
The MCP6054-E/ST can serve as a precision unity-gain buffer when a high-impedance source cannot directly drive the next circuit stage. Its unity-gain stability removes the need for an external compensation network, and the specified maximum input offset voltage of ±150 µV limits the DC error introduced into the buffered signal. Rail-to-rail output operation provides useful signal swing at a 1.8 V supply, although the final load and output-current requirements must be checked. Four channels allow several reference or sensor nodes to be buffered independently. Use short feedback traces, maintain the required input and output impedance, and confirm capacitive-load stability at the operating frequency.
推薦
Low-Voltage Instrumentation
The MCP6054-E/ST fits low-voltage instrumentation requiring compact signal amplification and accurate DC behavior. A typical gain-bandwidth product of 385 kHz supports general-purpose closed-loop gains for slow industrial, laboratory, or diagnostic signals, while the low offset specification benefits measurements where several channels compare small voltages. The four-channel TSSOP package simplifies routing and reduces component count compared with separate single amplifiers. At the system level, the 1.8 V operating capability allows the analog front end to operate near the voltage used by low-power sensors. Confirm noise density, input bias current, common-mode range, and output drive against the source and measurement bandwidth before selecting the final gain network.
推薦
Low-Noise Analog Signal Conditioning
The MCP6054-E/ST can condition low-level analog signals where input offset and rail-to-rail behavior are important. Its maximum input offset voltage of ±150 µV establishes the guaranteed DC offset limit, while rail-to-rail inputs help maximize signal utilization at low supply voltage. The 385 kHz typical gain-bandwidth product is appropriate for slow control, monitoring, and general analog-conditioning paths rather than high-speed waveform capture. Four channels can implement matched gain stages for bridge, current, or voltage measurements. The actual noise performance depends on the complete circuit, so evaluate the source impedance, resistor values, bandwidth, and required signal-to-noise ratio. Keep feedback loops compact and decouple the supply close to the device.
推薦
Power and Control Monitoring
The MCP6054-E/ST is suitable for multi-channel monitoring of power-system or process-control signals when the system operates from low supply voltages. Its four channels can monitor several scaled voltages or current-sense outputs, and rail-to-rail input and output behavior provides useful range near the 1.8 V minimum supply. The low quiescent current of approximately 30 µA per amplifier limits overhead in distributed monitoring electronics, while the ±150 µV maximum offset supports precision comparison of small signals. Choose resistor ratios that keep inputs inside the common-mode range and preserve output headroom. Confirm the required response time, noise performance, and temperature exposure for the monitored operating environment.
推薦
推薦產品摘要
工程參考資料,適用於 MCP6054-E/ST — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP6054T-E/ST | MCP6034-E/ST | MCP604T-I/ST | MCP6004T-E/ST |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP | 14-TSSOP |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 |
| Temperature Grade | E grade | T grade | E grade | I grade | T grade |
主要差異化特點
- Precision offset specification (對比MCP6004T-E/ST)
- Direct same-family temperature-range option (對比MCP6054T-E/ST)
- Four precision channels in one compact package (對比MCP6034-E/ST)
- Low-voltage operation with rail-to-rail behavior (對比MCP604T-I/ST)
設計說明
Place the supply bypass capacitor close to the amplifier supply and ground pins, with a short and low-inductance return path. For a four-channel device, each channel's feedback resistors should connect directly to the associated input and output pins, and unused amplifier inputs should be tied to a defined potential rather than left floating. Maintain the package land pattern and copper clearance specified by the manufacturer.
Keep the feedback loop physically small because parasitic resistance and capacitance can alter effective gain and stability. Avoid long traces around high-impedance inputs, where leakage and coupling can exceed the benefit of the ±150 µV offset specification. At low frequencies, add filtering close to the source; at higher frequencies, verify the closed-loop bandwidth against the 385 kHz typical gain-bandwidth product and the selected noise-gain configuration.
Do not treat rail-to-rail input or output as an unlimited range. The usable input range, output swing, and output-current capability remain limited by supply voltage and load. Verify the sensor output, common-mode range, output headroom, load capacitance, and temperature conditions. For a replacement, confirm that every 14-TSSOP pin has the same function and that the alternative's offset, bandwidth, noise, and quiescent-current limits satisfy the circuit requirements.
Estimated: four amplifiers operating at 30 µA each draw approximately 120 µA from the supply, excluding load current, bias-network current, and regulator overhead. This estimate uses the manufacturer's 30 µA per-amplifier figure and four channels. Actual supply demand can be higher during operation, so size the bypass network and power budget using the complete schematic and required transient performance.
合規資訊
The manufacturer family information identifies a low-power CMOS precision op amp, but no specific compliance declarations for the MCP6054-E/ST ordering code were confirmed. Compliance status must be checked against the current manufacturer product documentation before procurement.