MPC8360EZUAJDGA - 533MHz PowerQUICC II Pro MPU, TBGA-740 | NXP
MPN： MPC8360EZUAJDGA ✗ 停產MPC8360EZUAJDGA 概覽
A PowerQUICC processor is a family of integrated communications microprocessors from Freescale (now NXP) that combine a Power Architecture CPU with specialized networking peripheral logic. The PowerQUICC II Pro generation extends the original PowerQUICC II line by adding higher CPU frequencies, DDR memory support, gigabit Ethernet MACs, and a hardware security engine. In the system hierarchy, it sits as an MPU (microprocessor unit) within Power Management and embedded processing, used where deterministic packet processing and rich peripheral integration are required.
Key features include a 533 MHz e300 core, integrated QUICC Engine supporting common WAN protocols, dual GbE MACs with SGMII support, DDR1/DDR2 memory controller with ECC, USB 2.0 full-speed interface, PCI 2.2 bus, and an SEC 2.0+ cryptographic accelerator for IPsec and other security offload. The device operates from a 1.2 V core supply with 1.8 V/2.5 V/3.3 V I/O rails.
The MPC8360E uses a 0.13 um CMOS process and integrates roughly 100 million transistors, balancing performance with power for line-card and edge-router applications. The QUICC Engine offloads protocol processing from the e300 core, allowing wire-speed handling of ATM, Ethernet, TDM and MPLS traffic without CPU saturation.
Typical applications include small-to-medium enterprise routers, DSLAM line cards, IP-PBX systems, wireless base station controllers, and industrial networking gateways where integrated communications peripherals replace discrete MACs, PHYs and protocol processors.
When designing with this device, ensure the TBGA-740 land pattern uses 1 mm pitch with proper thermal via arrays under the die, and sequence the 1.2 V core rail before the 1.8/2.5/3.3 V I/O rails to prevent I/O latch-up. Boot configuration is sampled from reset and must be set before POR deassertion.
This page synthesizes distributor pricing, same-family NXP drop-in variants, end-of-life status signals, and practical PCB/design notes not found in the bare manufacturer datasheet.
直接替換替代品，適用於 MPC8360EZUAJDGA — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： MPC8360EZUAJDGA （相同外形與佔位） — 差異在於 Ethernet, USB, Architecture, Core Frequency, I/O Supply Voltage.
MPC8358EZUAGDGA
✅ 直接替換📋 參考替代品（不在目錄中）
MPC8360EZUAGDHA
✅ 直接替換📋 參考替代品（不在目錄中）
MPC8360ECZUAJDGA
✅ 直接替換📋 參考替代品（不在目錄中）
MPC8360EVVAJDGA
✅ 直接替換📋 參考替代品（不在目錄中）
MPC8360CVVAJDGA
✅ 直接替換📋 參考替代品（不在目錄中）
MPC8360EZUAJDGA 最大額定值與電氣特性
| Architecture | Power Architecture (e300 core), RISC |
| 資料匯流排寬度 | 32-bit |
| Core Frequency | 533 MHz |
| Supply Voltage (Core) | 1.2 V |
| I/O Supply Voltage | 1.8 V / 2.5 V / 3.3 V |
| Package Type | TBGA (LBGA), 37.50 x 37.50 mm, 1.46 mm height |
| Pin/Ball Count | 740 |
| Ball Pitch | 1.0 mm |
| 工作溫度 | 0 °C to +105 °C |
| Memory Controller | DDR1 / DDR2 with ECC |
| Ethernet | 1 Gbit Ethernet (tri-speed MACs, SGMII) |
| PCI | PCI 2.2 (32-bit, 66 MHz) |
| USB | USB 2.0 Full-Speed |
| Communications Acceleration | QUICC Engine (TDM, ATM, Ethernet, MPLS) |
| Security Engine | SEC 2.0+ (IPsec, crypto accelerators) |
| Process Technology | 0.13 um CMOS |
| JESD-609 Code | e0 |
| Lead Free | Yes (TBGA, lead-free) |
MPC8360EZUAJDGA tbga (lbga), 37.50 x 37.50 mm, 1.46 mm height 腳位配置指南
MPC8360EZUAJDGA（tbga (lbga), 37.50 x 37.50 mm, 1.46 mm height 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： MPC8360EZUAJDGA.
請參閱 資料表 以查看完整腳位配置。
典型應用
MPC8360EZUAJDGA 適用於 6 應用s: Small-to-Medium Enterprise Routers, DSLAM Line Cards, IP-PBX and Unified Communications Systems, Wireless Base Station Controllers, Industrial Networking Gateways, Network Attached Storage (NAS) Controllers.
Small-to-Medium Enterprise Routers
The MPC8360EZUAJDGA's 533 MHz e300 core, dual GbE MACs, and QUICC Engine hardware offload make it ideal for SME routers handling 100 Mbit/s to 1 Gbit/s WAN links. The QUICC Engine processes ATM, PPPoE, MPLS, and IPsec tunnels at wire speed without loading the e300 core. The integrated DDR1/DDR2 controller with ECC supports router DRAM needs without external memory chips, while the PCI bus connects to additional PHYs or expansion cards. Power sequencing between the 1.2 V core and 1.8/2.5/3.3 V I/O rails must be respected at POR to avoid I/O latch-up. Combined with NXP's Linux BSP and U-Boot support, this MPU delivers a complete router-on-chip solution for small-office gateways.
推薦
DSLAM Line Cards
DSLAM line cards aggregate hundreds of ADSL/VDSL subscribers and require deterministic packet processing; the MPC8360EZUAJDGA's QUICC Engine handles ATM AAL2/5 segmentation, SAR, and traffic shaping in hardware at line rate. The 533 MHz e300 runs the routing stack and management plane while the QUICC Engine manages the data plane, eliminating the need for a separate network processor. The SEC 2.0+ engine accelerates IPsec for secure VPN aggregation. The TBGA-740 package supports high-density line-card PCB layouts where multiple MPUs and DSL framer ICs share a backplane. Operating temperature of 0 to 105 °C matches central-office environments with adequate airflow.
推薦
IP-PBX and Unified Communications Systems
IP-PBX systems route VoIP calls between TDM and IP domains; the MPC8360EZUAJDGA integrates TDM interfaces, Ethernet MACs, and a Power Architecture core for running Asterisk or proprietary PBX software. The QUICC Engine accelerates RTP packetization and G.711/G.729 codec handling, offloading the e300 core. The PCI bus connects to additional TDM/E1 framer cards for legacy PSTN connectivity, while the USB 2.0 interface supports operator consoles. Hardware encryption via the SEC 2.0+ engine secures SIP/TLS media streams. The DDR2 controller with ECC ensures call-record integrity in commercial deployments.
推薦
Wireless Base Station Controllers
Wireless base station controllers aggregate 2G/3G Node-B traffic and require high-throughput packet processing with low jitter. The MPC8360EZUAJDGA's 533 MHz e300 and QUICC Engine deliver wire-speed processing of ATM and IP backhaul, while the integrated GbE MACs feed the backhaul link to the core network. The SEC engine accelerates IPsec tunnels for secure backhaul. The PCI bus connects to additional baseband cards or backhaul radios. The DDR2 memory controller with ECC handles real-time radio-resource-management databases. The 0 to 105 °C operating range suits outdoor-cabinet deployments.
推薦
Industrial Networking Gateways
Industrial gateways bridge Modbus/Profibus/Ethernet and forward data to SCADA systems, requiring deterministic latency and long-term reliability. The MPC8360EZUAJDGA's industrial operating temperature range and embedded Linux support make it suitable for factory-floor gateways. The QUICC Engine accelerates industrial protocol conversion (Modbus TCP/RTU, EtherNet/IP) at line rate, while the e300 core runs the gateway application stack. The PCI bus connects to fieldbus interface cards (CAN, RS-485). The SEC engine secures OPC UA traffic. The TBGA-740 package's 1.0 mm pitch supports dense industrial-PC-style motherboards with multiple expansion slots.
推薦
Network Attached Storage (NAS) Controllers
Entry-level NAS controllers can leverage the MPC8360EZUAJDGA's GbE MACs, PCI bus, and Power Architecture core for file-serving workloads. The 533 MHz e300 runs NAS software stacks (Linux + Samba/NFS), while the PCI bus connects to SATA RAID controllers. The DDR2 controller with ECC protects file-system metadata integrity. The QUICC Engine accelerates SMB/NFS protocol offload and TCP/IP checksum computation. Hardware encryption via SEC 2.0+ secures at-rest data via AES-XTS. The TBGA-740 package supports NAS mainboards with multiple SATA ports and gigabit uplinks for SOHO/mid-market NAS products.
推薦
推薦產品摘要
工程參考資料，適用於 MPC8360EZUAJDGA — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MPC8358EZUAGDGA | MPC8360EZUAGDHA | MPC8360ECZUAJDGA |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | TBGA-740 | TBGA-740 - same | TBGA-740 - same | TBGA-740 - same |
| Core Frequency | 533 MHz | 533 MHz | 533 MHz | 533 MHz |
| Security Engine | SEC 2.0+ (full) | Limited/absent | SEC 2.0+ (full) | SEC 2.0+ (full) |
| QUICC Engine | Full feature set | Subset (lower cost) | Full feature set | Full feature set |
| Operating Temperature | 0 °C to +105 °C | 0 °C to +105 °C | 0 °C to +105 °C | Extended grade |
| Lifecycle Status | EOL | EOL | EOL | EOL |
| Approx. Unit Price (qty 1) | USD 142.50 | USD 115-130 (lower) | USD 140-150 | USD 145-155 |
主要差異化特點
- Hardware-accelerated QUICC Engine offloads WAN protocols (對比MPC8358EZUAGDGA)
- Full SEC 2.0+ cryptographic engine included (對比MPC8358EZUAGDGA)
- Extended product family with drop-in TBGA-740 variants (對比QorIQ T1024 (different vendor platform))
設計說明
The TBGA-740 package dissipates 4-7 W typical at 533 MHz with full QUICC Engine load. Designers must implement a thermal via array under the die flag (central BGA region) with at least 9 vias of 0.3 mm drill connected to inner copper planes. Without adequate thermal vias, junction temperature can exceed 105 °C and trigger thermal protection. Use θJA of approximately 18 °C/W with proper via array; without vias, θJA rises to 35 °C/W or higher.
Sequence the 1.2 V core rail before the 1.8 V/2.5 V/3.3 V I/O rails using a power-management IC with Power-Good signal. Reverse sequencing causes I/O latch-up and can permanently damage the device. Hold the system reset pin low until all rails are stable for at least 100 ms. Use bulk decoupling of 100 uF tantalum plus 10 uF ceramic on each rail near the TBGA ball fields, plus 0.1 uF ceramic at every power pin.
The TBGA-740 1.0 mm pitch requires 4-layer PCB minimum with 0.5 oz copper outer layers and 1 oz inner planes. Microvia technology (laser-drilled stacked vias) is strongly recommended for breakout fanout. Maintain a continuous reference plane under DDR2 traces to control impedance (50 ohm single-ended, 100 ohm differential). Route DDR2 address/control traces with matched lengths within ±50 mil of clock, and DDR2 data within ±25 mil of DQS strobes.
Do not omit the QUICC Engine firmware upload during board bring-up; without firmware the QUICC Engine remains in reset and Ethernet ports will not link. Do not use 1.5 V DDR3 modules - the MPC8360E supports DDR1 and DDR2 only. Do not configure the local bus for 3.3 V peripherals without a level shifter; the local bus operates at the I/O voltage which is selected by hardware strapping at reset.
合規資訊
Lead-free TBGA package per manufacturer product description. RoHS/REACH lot-specific compliance must be confirmed via distributor CoC. JESD-609 code e0 on some stock lots indicates tin-lead ball finish. AEC-Q100 not applicable - this is an MPU not an automotive-grade IC.
