OPA251PA - 25µA Low-Power Rail-to-Rail Op Amp | Texas Instruments
MPN: OPA251PA ✓ 啟用中OPA251PA 概覽
An operational amplifier is an analog signal-conditioning semiconductor that amplifies the voltage difference between its inverting and non-inverting inputs. The OPA251 belongs to the broader hierarchy of operational amplifier, analog amplifier, amplifier IC, and power management semiconductor. Its micropower design is especially useful where battery energy must be conserved while the output must remain capable of driving a measurement, control, or conversion stage.
Important characteristics include 25 µA typical supply current, low input offset voltage, high common-mode rejection, and high open-loop gain. The 35 kHz gain-bandwidth product supports low-frequency signal conditioning, while the 0.01 V/µs slew rate is suitable for modest-amplitude waveforms. Rail-to-rail output operation increases usable output range in systems whose supply voltage is constrained.
The OPA251 uses a micropower internal architecture optimized for portable instrumentation rather than high-speed signal processing. With one amplifier in the 8-pin PDIP package, it supports cost-sensitive analog designs that need a single operational amplifier without the overhead of a dual or quad device. The 1.35 V minimum supply voltage also makes it applicable to low-energy sensor and monitoring circuits.
Typical uses include battery-powered sensor conditioning, portable measurement instrumentation, low-current analog signal processing, and the input stage of an analog-to-digital converter. In a typical application, the amplifier processes a sensor voltage referenced around ground, gains the signal to an appropriate level, and presents it to an ADC or comparator while minimizing standby current.
Designers should account for the 35 kHz bandwidth when selecting closed-loop gain and signal frequency. Input and output stability must be evaluated using the recommended application circuit, and the circuit must remain within the 1.35 V to 18 V supply range. Decoupling capacitors should be placed close to the supply pins to minimize supply disturbance.
This page organizes the OPA251PA electrical characteristics, package information, replacement considerations, and application guidance into an engineering-focused reference. It also identifies where an alternative is technically appropriate and, equally important, where a footprint or parameter mismatch makes a substitution unsuitable.
直接替換替代品,適用於 OPA251PA — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
OPA251PAG4
✅ 直接替換📋 參考替代品(不在目錄中)
OPA251PA 最大額定值與電氣特性
| Amplifier Type | Single operational amplifier |
| Supply Architecture | Single supply |
| Number of Channels | 1 channel |
| Nominal Supply Voltage | 15 V |
| Operating Supply Voltage Range | 1.35 V to 18 V |
| Typical Quiescent Current | 25 µA |
| Gain-Bandwidth Product | 35 kHz |
| Slew Rate | 0.01 V/µs |
| Output Swing | Rail-to-rail |
| 封裝 | 8-pin PDIP |
| 安裝類型 | Through-hole |
OPA251PA 8-pin pdip 腳位配置指南
OPA251PA(8-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: OPA251PA.
請參閱 資料表 以查看完整腳位配置。
典型應用
OPA251PA 適用於 3 應用s: 訊號調理, 資料擷取, 音訊處理.
訊號調理
使用 OPA251PA 放大與濾波感測器訊號。
資料擷取
使用 OPA251PA 將類比訊號轉換以供數位處理。
音訊處理
使用 OPA251PA 進行音訊訊號放大與處理。
工程參考資料,適用於 OPA251PA — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | OPA251PAG4 |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Single amplifier | Single amplifier |
| Supply Type | Single supply | Single supply |
| Supply Voltage Range | 1.35 V to 18 V | 1.35 V to 18 V |
| Typical Quiescent Current | 25 µA | 25 µA |
| Gain-Bandwidth Product | 35 kHz | 35 kHz |
| Slew Rate | 0.01 V/µs | 0.01 V/µs |
| Output Swing | Rail-to-rail | Rail-to-rail |
主要差異化特點
- Very low quiescent current for a general-purpose amplifier (對比OPA251PAG4)
- Single-supply operation extends to 1.35 V (對比OPA251PAG4)
- Same 8-pin PDIP mechanical interface (對比OPA251PAG4)
設計說明
Use the 25 µA typical quiescent current as the baseline for low-power design, but include feedback-network and load currents in the complete power budget. For a single-supply circuit, bypass the supply pins with ceramic capacitance placed close to the package and follow the manufacturer datasheet's recommended values. Check that the bypass capacitor's DC bias rating remains effective at the actual supply voltage.
Treat the 35 kHz gain-bandwidth product as the primary limit on usable closed-loop bandwidth. Increasing closed-loop gain reduces bandwidth and can also increase output-noise contribution. For sensor signals, select a gain that keeps the signal bandwidth below the corresponding gain-bandwidth limit with margin, then verify phase margin and output settling using the datasheet curves for the intended operating supply.
Do not assume that the rail-to-rail output specification removes all common-mode restrictions at the input. Verify the input common-mode range, output swing, offset behavior, and stability against the manufacturer datasheet for the selected gain and load. The 0.01 V/µs slew rate can also limit large-amplitude output transitions, making it unsuitable for fast pulse or waveform requirements.
Keep the 8-pin PDIP footprint and its pin assignments unchanged when using OPA251PAG4 as the lead-free ordering option. Confirm orientation against the pin-description table in the manufacturer datasheet rather than a generic operational-amplifier symbol. Maintain a low-impedance ground return and place input components so their parasitic capacitance does not create excessive feedback or reduce phase margin.
合規資訊
The OPA251PA is a general-purpose operational amplifier rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements require confirmation from the manufacturer's current product or material documentation.